notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the
latest version of this device specification before relying on any published information and before placing orders for products.
Integrated Silicon Solution, Inc.
Rev. 00A
09/10/08
1
Preliminary
IS43R16160
Pin Assignment (Top View) 66-pin TSOP
A3S56D30/40ETP
256M Double Data Rate Synchronous DRAM
CLK, /CLK
CKE
/CS
/RAS
/CAS
/WE
DQ0-15
DQ0-7
UDM, LDM
DM
UDQS, LDQS
DQS
: Master Clock
: Clock Enable
: Chip Select
: Row Address Strobe
: Column Address Strobe
: Write Enable
: Data I/O (x16)
: Data I/O (x8)
: Write Mask (x16)
: Write Mask (x8)
: Data Strobe (x16)
: Data Strobe (x8)
A0-12
BA0,1
V
DD
V
DDQ
Vss
Vss
Q
: Address Input
: Bank Address Input
: Power Supply
: Power Supply for Output
: Ground
: Ground for Output
DDR SDRAM (Rev.1.1)
2
Integrated Silicon Solution, Inc.
Rev. 00A
09/10/08
Zentel Electronics Corporation
I
Preliminary
IS43R83200B
IS43R16160
IS43R16160B, IC43R16160B
PIN FUNCTION
SYMBOL
TYPE
DESCRIPTION
A3S56D30/40ETP
256M Double Data Rate Synchronous DRAM
CLK, /CLK
Input
Clock: CLK and /CLK are differential clock inputs. All address and control
input signals are sampled on the crossing of the positive edge of CLK and
negative edge of /CLK. Output (read) data is referenced to the crossings of
CLK and /CLK (both directions of crossing).
Clock Enable: CKE controls internal clock. When CKE is low, internal clock
for the following cycle is ceased. CKE is also used to select auto / self refresh.
After self refresh mode is started, CKE becomes asynchronous input. Self refresh
is maintained as long as CKE is low.
Chip Select: When /CS is high, any command means No Operation.
Combination of /RAS, /CAS, /WE defines basic commands.
A0-12 specify the Row / Column Address in conjunction with BA0,1. The
Row Address is specified by A0-12. The Column Address is specified by
A0-8(x16). A10 is also used to indicate precharge
option.
When A10 is high at a read / write command, an auto precharge is
performed. When A10 is high at a precharge command, all banks are
precharged.
Bank Address: BA0,1 specifies one of four banks to which a command is
applied. BA0,1 must be set with ACT, PRE, READ, WRITE commands.
Data Input/Output: Data bus
Data Strobe: Output with read data, input with write data. Edge-aligned
with read data, centered in write data. Used to capture write data.
For the x16, LDQS corresponds to the data on DQ0-DQ7; UDQS
correspond to the data on DQ8-DQ15
Input Data Mask: DM is an input mask signal for write data. Input data
is masked when DM is sampled HIGH along with that input data
during a WRITE access. DM is sampled on both edges of DQS.
Although DM pins are input only, the DM loading matches the DQ
and DQS loading. For the x16, LDM corresponds to the data on DQ0-DQ7;
UDM corresponds to the data on DQ8-DQ15.
Power Supply for the memory array and peripheral circuitry.
V
DDQ,
and
V
SSQ
are supplied to the Output Buffers only.
CKE
Input
/CS
/RAS, /CAS, /WE
Input
Input
A0-12
Input
BA0,1
D
DQ0-15 (x16)
Input
Input / Output
D
Input / Output
UDQS, LDQS (x16)
D
UDM, LDM (x16)
Input
V
DD
,
V
SS
V
DDQ,
V
SSQ
Power Supply
Power Supply
Input
Vref
SSTL_2 reference voltage.
Integrated Silicon Solution,
DDR SDRAM (Rev.1.1)
Inc.
Rev. 00A
09/10/08
3
IS43R16160
BLOCK DIAGRAM x16
DLL
DQ 0 - 15
UDQS, LD QS
I/O B uffer
DQ S Buffer
Memory
Array
Bank #0
Memory
Array
Ba nk #1
Memory
Array
Ba nk #2
Memory
Array
Ba nk #3
Mode Re gister
Control C ircu itry
Addres s B uffer
Cl ock B uffer
A0-1 2
BA 0,1
CLK
/CLK
CKE
Control Signal B uffer
/CS /RAS /CAS
/WE
UDM ,
LD M
4
Integrated Silicon Solution, Inc.
Rev. 00A
09/10/08
Zentel Electronics Corporation
IS43R16160
Preliminary
A3S56D30/40ETP
256M Double Data Rate Synchronous DRAM
ISSI's 256-Mbit DDR SDRAM
provides basic functions, bank (row) activate, burst read / write, bank
(row) precharge, and auto / self refresh. Each command is defined by control signals of /RAS,
/CAS and /WE at CLK rising edge. In addition to 3 signals, /CS , CKE and A10 are used as chip
select, refresh option, and precharge option, respectively. To know the detailed definition of
commands, please see the command truth table.
/CLK
CLK
/CS
/RAS
/CAS
/WE
CKE
A10
Chip Select : L=select, H=deselect
Command
Command
Command
Refresh Option @refresh command
Precharge Option @precharge or read/write command
define basic commands
BASIC FUNCTIONS
Activate (ACT) [/RAS =L, /CAS =/WE =H]
ACT command activates a row in an idle bank indicated by BA.
Read (READ) [/RAS =H, /CAS =L, /WE =H]
READ command starts burst read from the active bank indicated by BA. First output data appears after
/CAS latency. When A10 =H at this command, the bank is deactivated after the burst read (auto-
precharge,
READA)
Write (WRITE) [/RAS =H, /CAS =/WE =L]
WRITE command starts burst write to the active bank indicated by BA. Total data length to be written
is set by burst length. When A10 =H at this command, the bank is deactivated after the burst write
(auto-precharge,
WRITEA)
Precharge (PRE) [/RAS =L, /CAS =H, /WE =L]
PRE command deactivates the active bank indicated by BA. This command also terminates burst read
/write operation. When A10 =H at this command, all banks are deactivated (precharge all,
PREA
).
Auto-Refresh (REFA) [/RAS =/CAS =L, /WE =CKE =H]
REFA command starts auto-refresh cycle. Refresh address including bank address are generated
internally. After this command, the banks are precharged automatically.
As an important parameter in the field of industrial control, how to improve the accuracy of its measurement has always been one of the issues that industry insiders have been studying. Ultrasonic flo...
Warning (10631): VHDL Process Statement warning at rams.vhd(35): inferring latch(es) for signal or variable "dout", which holds its previous value in one or more paths through the process Warning (106...
The RF-1800 Runfei programmer cannot communicate with the computer. I need help. Does anyone have the driver? The CD that came with it is gone. I need it urgently. Thank you!...
Filter capacitors are used in power rectifier circuits to filter out AC components. This makes the output DC smoother. Decoupling capacitors are used in places where AC is not required in amplifier ci...
This article will first explain the basic method of using I2C in BBB, then use the driver that comes with BBB to read the air pressure value from the pressure sensor chip BMP085, and finally give how ...
I need help from the experts in the forum. A lot of Jlinks are broken here. It seems that the firmware is basically lost. I have tried many methods mentioned on the Internet to flash the firmware, whi...
In early 2002, I started to write a working program for an IC card prepaid electricity meter. The meter used Philips' 8-bit 51-expanded single-chip microcomputer
87LPC764
, and wa...[Details]
This article discusses how to wake up a touch-sensitive device such as a tablet without touching the device, using basic gesture recognition and novel proximity sensors. The article discusses the p...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guang...[Details]
1. Introduction
Since the 1980s, with the continuous development of automotive electronic technology, there are more and more electronic control units in automobiles, such as electronic fuel i...[Details]
Do you often have to add brake fluid to your car's brakes? The fact that you need to pump out the brake fluid to make sure there is no gas in the brake fluid line may not be done by the car owner h...[Details]
Analog engineers have traditionally struggled with complexity when designing power supplies that required multiple outputs, dynamic load sharing, hot-swap, or extensive fault-handling capabilities....[Details]
The reason for the light decay of white LEDs: the decline of phosphor performance
So far, the rapid decline of the luminous performance of white light LEDs, especially low-power white light LE...[Details]
For a long time, due to the limitation of hardware conditions, the display devices of traditional small handheld devices such as PDA are usually monochrome LCD, and the user interface is very simpl...[Details]
Experimental tasks
A DS18B20 is used to form a temperature measurement system. The temperature measurement accuracy reaches 0.1 degrees. The temperature range is between -20 degrees and +50 de...[Details]
In 2012, more than half of the cars in the European, Japanese and American car markets will be equipped with color displays, navigation systems, satellite communications and other in-vehicle infota...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guangzho...[Details]
0 Introduction
There are many types of sensors, and the working principles, measurement targets and measurement environments of different types of sensors vary greatly. The corresponding detection s...[Details]
Abstract: In order to realize wireless automatic alarm and monitoring of major safety places, based on the basic principle of pyroelectric infrared sensing, a detector for receiving infrared radia...[Details]
1 What is an LED floodlight?
LED downlights are also called spotlights, projection lamps, and spotlights. They are mainly used for architectural decorative lighting and commercial space lighti...[Details]
The demand for improved healthcare environments is endless, so medical imaging equipment with higher resolution is needed to better observe the human body. High resolution brings problems with sign...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
