302074-5T105K00UB datasheet, PDF

Datasheet> All Categories > Passive components> The resistor> 302074-5T105K00UB

302074-5T105K00UB: DescriptionFixed Resistor, Metal Foil, 1.25W, 105000ohm, 500V, 0.002% +/-Tol, -2,2ppm/Cel,; CategoryPassive components The resistor; File Size451KB，6 Pages; ManufacturerVishay; Websitehttp://www.vishay.com; Environmental Compliance

Download Datasheet Parametric View All

302074-5T105K00UB Overview

Fixed Resistor, Metal Foil, 1.25W, 105000ohm, 500V, 0.002% +/-Tol, -2,2ppm/Cel,

302074-5T105K00UB Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	850612498
Reach Compliance Code	compliant
ECCN code	EAR99
structure	Hermetically Sealed
JESD-609 code	e3
Lead diameter	0.64 mm
Lead length	25.4 mm
Number of terminals	4
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package diameter	12.7 mm
Package length	25.4 mm
Package form	4 Terminals
method of packing	Bulk
Rated power dissipation(P)	1.25 W
resistance	105000 Ω
Resistor type	FIXED RESISTOR
series	H(OTHER)
technology	METAL FOIL
Temperature Coefficient	2 ppm/°C
Terminal surface	Tin (Sn)
Tolerance	0.002%
Operating Voltage	500 V

Preview

Download Datasheet

View All

H Series

Vishay Foil Resistors

New Generation of Secondary Standards Hermetically Sealed High Precision Bulk

Metal

Foil Technology Resistors with TCR of ± 2 ppm/°C, Tolerance of ± 0.001 % and

Load Life Stability of ± 0.005 % (Metrology, Laboratory, Instrumentation, Industrial)

FEATURES

•

Temperature coefficient of resistance (TCR):

± 2 ppm/°C typical (- 55 °C to + 125 °C, + 25 °C

ref.).

For

ultra

high

performances

(instrumentation and metrology) please refer to

the last page

•

Resistance range: 5

to 1.84 MΩ (higher or

lower values of resistance available)

•

Vishay Foil resistors are not restricted to standard values;

specific “as required” values can be supplied at no extra

cost or delivery (e.g. 1K2345 vs. 1K)

•

Power rating: 0.3 W to 2.5 W at + 25 °C (depending on

model - see table 2)

•

Tolerance: to ± 0.001 % (10 ppm)

•

Load life stability to ± 0.002 % (20 ppm) at 25 °C, 2000 h

at rated power

•

Load life stability can be considerably improved

through in-house stabilization

•

Shelf life stability: ± 2 ppm for at least 6 years

(unaffected by humidity)

•

Electrostatic discharge (ESD) up to 25 000 V

•

Rise time: 1 ns effectively no ringing

•

Thermal stabilization time < 1 s (nominal value achieved

within 10 ppm of steady state value)

•

Current noise: 0.010 µV

RMS

/V of applied voltage (< - 40 dB)

•

Thermal EMF: 0.05 µV/°C typical

•

Voltage coefficient: < 0.1 ppm/V

•

Non-inductive: < 0.08 µH

•

Non-inductive, non-capacitive design

•

Non hot spot design

•

Terminal finish available: lead (Pb)-free or tin/lead alloy

•

Impervious to harmful environments - oil-filled

•

Compliant to RoHS directive 2002/95/EC

•

Prototype quantities available in just 5 working days

or sooner. For more information, please contact

foil@vishaypg.com

•

For better performances (values, TCR, tolerance, stability),

please see the HZ series

INTRODUCTION

The H series resistors are oil-filled, hermetically sealed ultra

precision resistors and are used as secondary standards for

metrology applications.

The hermetic sealing eliminates the ingress of moisture and

oxygen, while the oil acts as a thermal conductor, thus

eliminating the long-term degradation elements of unsealed

resistors, while at the same time allowing the device to

accept short periods of overload without degradation.

Vishay’s Bulk Metal

Foil outperforms all other resistor

technologies available today for applications that require

precision and stability. When combined with the hermetic

sealing and oil filling, the H series resistors become

the most

precise and stable resistors available.

With accuracies of 0.001 %, a resistance range from 5

to 1.84 MΩ, and long term shelf life of less than 2 ppm,

these devices are virtually secondary standards that can be

carried in sets for daily or periodic calibration of factory

measurement equipment.

The H series is available with laboratory and metrology

level precision and long-term stability with additional

in-house oriented processes such as: chip stabilization,

special TCR plotting, additional treatments for ultra

stability and special post manufacturing operations

(PMO). (Please refer to the last page)

TABLE 1 - TCR VS. RESISTANCE VALUE

RESISTANCE

VALUE (Ω)

100 to < 1M84

50 to < 100

5 to < 50

TYPICAL TCR AND MAX. SPREAD

(- 55 °C to + 125 °C, + 25 °C ref.)

(ppm/°C)

± 2 ± 2.5

± 2 ± 3.5

± 2 ± 4.5

FIGURE 1 - SHELF LIFE - VHA518-11

12K9 VS. QHE

0.9

0.8

0.7

0.6

0.5

0.4

0.3

0.2

0.1

- 0.1

100 200 300 400 500 600 700 800 900 1000

Note

• For maximum TCR < 1 ppm/°C, see VHP100 and contact

application engineering

* Pb containing terminations are not RoHS compliant, exemptions may apply

Resistance Change (ppm)

Time (Days)

Document Number: 63006

Revision: 23-Mar-10

For any questions, contact:

foil@vishaypg.com

www.foilresistors.com

Recommended Resources

RF Tuned Amplifier Circuit Diagram C

Sample and hold circuit 2 circuit diagram

555 short line anti-theft alarm

Triac light dimmer

The most practical basic diagram circuit 46 - zero line current and phase failure protection circuit

Microphone and its testing

AD19 only shows wireframe after copper is laid, which does not look like laid copper: Dear friends, why does my AD19 only show the wireframe after copper laying, but not the laid copper, as shown in the picture? Is there any setting? Switch to AD10 and open it, double-click the copper ...; AshleyZhai PCB Design

The DLL entry DLLMain is called twice by the system using DLL_PROCESS_DETACH: Under CE5, I wrote a USB driver for Motola mobile phone. Now it loads OK. The information from the serial port is as follows: USBInstallDriver++ load USBD.DLL sucess! USBInstallDriver-- DLL_PROCESS_DE...; hsdzcf Embedded System

I now have the stm32f103 minimum system ban and the ov7670 camera with FIFO. If I want the minimum system version to use...: I now have a stm32f103 minimum system board and an ov7670 camera with FIFO. If I want to use the ov7670 camera with the minimum system board, can I not connect the pins directly? Do I need to make a d...; LOVELESS燚 stm32/stm8

STEP Model: [i=s]This post was last edited by paulhyde on 2014-9-15 04:02[/i] Are you still using the built-in component library of Altium Designer? Or a self-built library? Are you worried about the lack of Step...; philips_lu Electronics Design Contest

How to convert a string of uchar data into hexadecimal numbers and send it?: I originally planned to send 7E 01 01 00 01 01 04 0D. The original program was: Call: SendString_PH_START("7E 01 01 00 01 01 04 0D"); Definition: void SendString_PH_START(uchar *ptr) { for(int j=0;j<2...; 面纱如雾 Microcontroller MCU

Engineers grew up amid the smoke from cooking -- ADI Laboratory Circuit DIY Competition Postscript: There is a group of "silly kids" who are always at odds with themselves. After busy work, they often sit in front of their desks to disassemble and disassemble. The smoke from cooking is commonplace. ...; soso ADI Reference Circuit

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components