Normally, when developing and debugging a DSP system, an SRAM chip is required as an off-chip program RAM. During debugging, the corresponding simulation board is used to download the program to the S...
:) Dear engineer friends, we are looking for NXP CORTEX-M0 M3 projects, and there are free samples for you!
Friends who are interested can join the QQ group~~~
Contact: Jiang R
Tel: 13723455874
QQ: 61...
[size=4][color=#0000ff]My spectrum analyzer suddenly stopped turning on a while ago. I spent 30,000 yuan on it in 2013. Now it doesn't turn on. I'm so sad. I can't bear to sell it, so I came up with a...
LM-400 Network temperature and humidity acquisition module without display (with built-in sensor) LM-410 Network temperature and humidity acquisition module with display (with built-in sensor) LM-420 ...
[i=s]This post was last edited by strong161 on 2017-6-6 09:09[/i] [size=4][color=#ff0000]Limited to honest transactions[/color] [/size][size=4] Sell one or one set of Atmel zigbee modules based on sam...
I am writing a BSP for a mips32 CPU, using Tornado2.2. I wrote several cache functions (such as cache_reset) in cacheALib.s, and called them after declaring them with IMPORT void cache_reset(void) in ...
Microchip's PIC18F46J50 is a low-power, high-performance 8-bit USB microcontroller (MCU) using nanoWatt XLP technology. The current in deep sleep mode can be as low as 13nA, the operating voltage i...[Details]
With the rapid development of science and technology, especially the widespread application of digital technology and various ultra-large-scale integrated circuits, electronic equipment, especially...[Details]
Two simple circuits are implemented to drive two LEDs from a battery powered microprocessor.
This design is based on a circuit that uses three resistors and a microprocessor I/O pin as an input h...[Details]
1 Introduction
As an emerging microfabrication technology, micro-electromechanical system (MEMS) technology has begun to be applied in various fields. It can integrate functions such as inform...[Details]
Microcalorimetry
is used to determine energy relationships. Microcalorimetry techniques are often required when performing calorimetric experiments with small sample sizes or slow heating rat...[Details]
Product series: PB-B-RS232/485 interface (hereinafter sometimes referred to as "interface") is a product in the PROFIBUS bus bridge series.
The main purpose of the bridge series ...[Details]
Since the No. 4 blast furnace of Handan Iron and Steel was put into operation in 1993, its external equipment has been seriously aged, and the original PLC control system TDC3000 of the hot blast furn...[Details]
Flooded Batteries
This battery developed in Germany can be used to power flashlights, strobe lights and toys as long as it is filled with water. This battery can be stored for 50 years and can...[Details]
Introduction
Liquid crystal, as a display device, is widely used in low-power products such as instruments, meters, and electronic equipment with its unique advantages. In the past, the displ...[Details]
introduction
MAX6636 is a multi-channel precision temperature monitor that can not only monitor local temperature, but also connect up to 6 diodes externally. Each channel has a programmable...[Details]
System Overview
The system consists of a signal preprocessing circuit, a single-chip computer AT89C2051, a systematic LED display module, a serial port data storage circuit and system software...[Details]
1 Introduction
With the rapid economic development, my country's electricity demand has been growing at a rate of more than 20% per year. According to the current economic development trend an...[Details]
One in five car failures are caused by batteries, a problem that will become more serious in the coming years as electric-by-wire, start/stop engine management and hybrid (electric/gas) vehicles be...[Details]
DCDC means DC to DC (conversion of different DC power values). Anything that meets this definition can be called a DCDC converter. Specifically, it means converting the input DC into AC through a s...[Details]
The power consumption of a switching power supply includes fixed losses caused by parasitic resistances such as semiconductor switches, magnetic components, and wiring, as well as switching losses ...[Details]