Using the IDT CMOS Oscillator technology, originally developed by
Mobius Microsystems, the MM8202 replaces quartz crystal based
resonators and oscillators with a monolithic CMOS IC at the thinnest
possible form factors without the use of any mechanical frequency
source or PLL. The product is specially designed to work with the
next generation USB 2.0 High Speed, USB 2.0 Full/Low Speed and
USB-IC (USB-InterChip) interface controller ICs, and high density
SIM-, and smart-cards.
Features
• All-CMOS Temperature Compensated Oscillator
• TimeStak
TM
: Available in die form for the thinnest and smallest
MCP options (-D package option)
• Ultra-low power operation (2mA typical at 1.8V supply)
• No quartz or PLL used: very low jitter performance leading to low
link Bit Error Rates (BER)
• Excellent reliability: Shock and vibration resistant
• Many frequencies are supported
• Factory programmable from 6 to 133MHz
Ordering Information
8202
1
-
12
2
VP
3
C
4
NSG
5
6
T
7
Pin Assignment
1) IDT Base Part Number
2) FF: Factory Programmed Frequency in MHz
3) Supply Voltage Configuration
•
•
•
•
•
•
•
•
•
•
•
•
VP: 1.8V to 3.3V continuous operation
V: 3.3V only operation
T: 2.5V only operation
P: 1.8V only operation
C: CMOS Output
-D: Wafer form 200um thickness
-C: Wafer form 350um thickness
NSG: 5x3.2, 4-Pin Package
NVG: 2.5x2.0, 4-Pin Package
No
1
Name
CE
MM8202
4-pin NSG
5mm x 3.2mm x 0.9mm
Top View
CE
1
2
VSS
Bottom View
VDD
4
3
OUT
4) Output Signal Type
5) Package Options*
Table 1. Pin Descriptions
Type
Input
Pullup
Description
Chip Enable. Internal Pullup. MM8202 is
enabled when HIGH.When LOW, OUT has
a weak pull-down to GND internally
System Ground
Frequency Output
Power Supply. Use a 0.1µF decoupling
capacitor between VDD and VSS
6) Temperature Grade
“ “: 0 to 70 C Commercial Temperature Range i.e. default is blank
“ “: Shipped in Tube i.e. default is blank
T: Shipped in Tape & Reel
o
7) Tape & Reel Option
2
This product is rated “Green”. Please contact factory for environmental compliancy
information.
VSS
OUT
VDD
Power
Output
Power
3
4
The Preliminary Information presented herein represents a product in pre-production. The noted characteristics are based on initial product characterization and/or qualification.
Integrated Device Technology, Incorporated (IDT) reserves the right to change any circuitry or specifications without notice
may cause permanent damage to the device. These ratings are stress
specifications only. Functional operation of product at these conditions or any conditions beyond those listed in the
DC Characteristics
or
AC
Characteristics
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect product reliability.
Item
Supply Voltage, VDD
Input, V
I
(CE pin)
Output, V
O
(OUT pin)
Storage Temperature
4.6V
Rating
-0.5V to VDD + 0.5V
-0.5V to VDD + 0.5V
-65
o
C to 150
o
C
Electrical Characteristics
5
[3.3V]
VDD=3.0V to 3.6V, T
A
=0 to 70
o
C unless otherwise noted. Typical values are measured at VDD=3.3V, T
A
=35
o
C
Parameter
ElectroStaticDischa
rge
Supply Voltage
Input LOW level
Input HIGH level
Supply Current
Quiescent Current
Output LOW level
Output HIGH level
Output Frequency
Frequency Stability
Rise Time
Fall Time
Duty Cycle
Symbol
ESD
VDD
V
IL
V
IH
IDD
IDDQ
V
OL
V
OH
F
OUT
F
TOT
RT
FT
DC
Conditions
Human Body Model, tested per JESD D22-A114
Normal Operation
3
CE pin
CE pin
Active supply current, VDD=3.3V, T=35oC, no output load
CE=LOW, output disabled
I
OL
= -4mA
I
OH
= 4mA
Factory Programmable.Contact IDT for frequencies not listed
Total Frequency Stability over temperature,supply
variation,aging (1st year at 35oC),shock&vibration. “ ” device
option, over 0-70
o
C range
20% to 80% x VDD. Output load (C
L
) =8pF, NSG-option
80% to 20% x VDD. Output load (C
L
) =8pF, NSG-option
Clock output duty cycle. Measured under 80MHz, VDD/2,
C
L
=8pF
Clock output duty cycle. Measured over 80MHz, VDD/2,
C
L
=8pF
Output valid time after VDD meets the specified range&CE
transition
Total RMS Period Jitter (including random and
deterministic)
1,2
The absolute value of max change in the periods of any 2
adjacent cycles
1,2,4
1MHz offset from carrier
1,2
Min
4000
3.0
-0.3
VDD*0.7
Typ
Max
Units
V
3.3
2.5
0.2
VDD-0.5
6
3.6
VDD*0.3
VDD+0.3
3.0
1
0.5
133
+400
1.9
1.9
12,24,25,50
V
V
V
mA
µA
V
V
MHz
ppm
ns
ns
%
%
µs
ps
RMS
45
40
400
3.5
55
60
Power-up time
Period Jitter
Cycle-cycle Jitter
Phase Noise
t
on
PJ
RMS
CJ
PN
50
-140
-135
ps
dBc/Hz
Notes 1. Measured with a 50Ω to GND termination
2: Measured at 48MHz output frequency
3. The MM8202 will support continuous VDD operation from 1.62 to 3.6V. The device can be powered up with a supply voltage at any of the 3 main supply rails of 1.8V, 2.5V or 3.3V.
4. Measured over 1000 cycles per JEDEC standard 65
5. Electrical parameters are guaranteed over the specified ambient operating temperature range, which is established when the device is mounted in a test socket with maintained
transverse airflow greater than 500lfpm. The device will meet specifications after thermal equilibrium has been reached under these conditions.
C unless otherwise noted. Typical values are measured at VDD=2.5V, T
A
=35
o
C
Parameter
ElectroStaticDischa
rge
Supply Voltage
Input LOW level
Input HIGH level
Supply Current
Quiescent Current
Output LOW level
Output HIGH level
Output Frequency
Frequency Stability
Rise Time
Fall Time
Duty Cycle
Symbol
ESD
VDD
V
IL
V
IH
IDD
IDDQ
V
OL
V
OH
F
OUT
F
TOT
RT
FT
DC
Conditions
Human Body Model, tested per JESD D22-A114
Normal Operation
3
CE pin
CE pin
Active supply current, VDD=2.5V, T=35oC, no output load
CE=LOW, output disabled
I
OL
= -3mA
I
OH
= 3mA
Factory Programmable.Contact IDT for frequencies not listed
Total Frequency Stability over temperature,supply
variation,aging (1st year at 35oC),shock&vibration. “ ” device
option, over 0-70
o
C range
20% to 80% x VDD. Output load (C
L
) =7pF, NSG-option
80% to 20% x VDD. Output load (C
L
) =7pF, NSG-option
Clock output duty cycle. Measured under 100MHz at VDD/2,
C
L
=7pF
Clock output duty cycle. Measured over 100MHz at VDD/2,
C
L
=7pF
Output valid time after VDD meets the specified range&CE
transition
Total RMS Period Jitter (including random and
deterministic)
1,2
The absolute value of max change in the periods of any 2
adjacent cycles
1,2,4
1MHz offset from carrier
1,2
Min
4000
2.25
-0.3
VDD*0.7
Typ
Max
Units
V
2.5
2.25
0.2
VDD-0.4
6
2.75
VDD*0.3
VDD+0.3
2.75
1
0.4
133
+400
2.3
2.3
12,24,25,50
V
V
V
mA
µA
V
V
MHz
ppm
ns
ns
%
%
µs
ps
RMS
45
40
400
3.5
55
60
Power-up time
Period Jitter
Cycle-cycle Jitter
Phase Noise
t
on
PJ
RMS
CJ
PN
50
-140
-135
ps
dBc/Hz
Notes 1. Measured with a 50Ω to GND termination
2: Measured at 48MHz output frequency
3. The MM8202 will support continuous VDD operation from 1.62 to 3.6V. The device can be powered up with a supply voltage at any of the 3 main supply rails of 1.8V, 2.5V or 3.3V.
4. Measured over 1000 cycles per JEDEC standard 65
5. Electrical parameters are guaranteed over the specified ambient operating temperature range, which is established when the device is mounted in a test socket with maintained
transverse airflow greater than 500lfpm. The device will meet specifications after thermal equilibrium has been reached under these conditions.
C unless otherwise noted. Typical values are measured at VDD=1.8V, T
A
=35
o
C
Parameter
ElectroStaticDischa
rge
Supply Voltage
Input LOW level
Input HIGH level
Supply Current
Quiescent Current
Output LOW level
Output HIGH level
Output Frequency
Frequency Stability
Rise Time
Fall Time
Duty Cycle
Power-up time
Period Jitter
Cycle-cycle Jitter
Phase Noise
Symbol
ESD
VDD
V
IL
V
IH
IDD
IDDQ
V
OL
V
OH
F
OUT
F
TOT
RT
FT
DC
t
on
PJ
RMS
CJ
PN
Conditions
Human Body Model, tested per JESD D22-A114
Normal Operation
3
CE pin
CE pin
Active supply current, VDD=1.8V, T=35oC, no output load
CE=LOW, output disabled
I
OL
= -1.8mA
I
OH
= 1.8mA
Factory Programmable.Contact IDT for frequencies not listed
Total Frequency Stability over temperature,supply
variation,aging (1st year at 35oC),shock&vibration. “ ” device
option, over 0-70
o
C range
20% to 80% x VDD. Output load (C
L
) =4pF, NSG-option
80% to 20% x VDD. Output load (C
L
) =4pF, NSG-option
Clock output duty cycle. Measured at VDD/2, C
L
=4pF
Output valid time after VDD meets the specified range&CE
transition
Total RMS Period Jitter (including random and
deterministic)
1,2
The absolute value of max change in the periods of any 2
adjacent cycles
1,2,4
1MHz offset from carrier
1,2
Min
4000
1.62
-0.3
VDD*0.7
Typ
Max
Units
V
1.8
2.0
0.2
VDD-0.3
6
1.98
VDD*0.3
VDD+0.3
2.5
1
0.3
133
+400
2.75
2.75
55
12,24,25,50
V
V
V
mA
µA
V
V
MHz
ppm
ns
ns
%
µs
ps
RMS
45
400
3.5
50
-140
-135
ps
dBc/Hz
Notes 1. Measured with a 50Ω to GND termination
2: Measured at 48MHz output frequency
3. The MM8202 will support continuous VDD operation from 1.62 to 3.6V. The device can be powered up with a supply voltage at any of the 3 main supply rails of 1.8V, 2.5V or 3.3V.
4. Measured over 1000 cycles per JEDEC standard 65
5. Electrical parameters are guaranteed over the specified ambient operating temperature range, which is established when the device is mounted in a test socket with maintained
transverse airflow greater than 500lfpm. The device will meet specifications after thermal equilibrium has been reached under these conditions.
Application Diagram
Below is a representative application diagram to evaluate the MM8202. For 50Ohm terminated measurements, a balun is necessary to
I have been debugging the SPI interface these days. The minimum system has been completed and the LED can be turned on. Now I am debugging the SPI interface, but the SPI pins are not connected to any ...
[Recommendations for 10 Typical Laboratory Circuits] 6: This circuit uses a low-noise, low-dropout (LDO) linear regulator to power a broadband integrated PLL and VCO. The broadband voltage-controlled ...
module add_4(X, Y, Sum, C); input[3:0] X, Y; output[3:0] Sum; output C; assign {C, Sum} =X + Y; endmodule I first created a new project file— new project wizard. The project name is the same as the en...
Why does a white LED change color when the voltage is adjusted?How many volts should it be?Actually, I heard from a customer last time that there are many series, such as 3.0-3.2, 3.2-3.4, 3.4-3.6; do...
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 19:59[/i] [:)][:)]The naming convention of Acer notebooks: Travel Mate is positioned for business applications, and generally uses ordin...
The core of a machine vision system is image acquisition and processing. All information comes from images, and image quality is crucial to the entire vision system. A good image can improve the st...[Details]
In recent years, with the increasing demand for manufacturing and automated production management, industrial barcode scanners have gradually become an indispensable part of the industrial manufact...[Details]
If the ultimate form of a car is a silicon-based life form, then in
the field of
intelligent driving
, it has gradually taken on the appearance of a "veteran driver." In
the field of
the ...[Details]
Recently, South Korean robotics giant WIRobotics launched its first general-purpose humanoid robot, ALLEX, at the Robotics Innovation Center (RIH) at the Korea University of Science and Technology....[Details]
Magna's integrated in-cabin perception system fuses vision and millimeter-wave radar data to detect the presence of passengers, identify stranded children, monitor driver fatigue and vital signs, a...[Details]
For today's new energy vehicles, they have different configurations from fuel vehicles, and some configurations have also become a selling point for manufacturers. Compared with traditional vehicle...[Details]
The composition of the water heater
The water heater itself is divided into the following parts:
1. Water tank.
This is where the water heater is filled with water and where the wate...[Details]
Definitions of VR
, AR, and MR:
What is Virtual Reality?
Virtual Reality (VR), also known as "spiritual realm" or "illusion," is a high-tech technology that has emerged in recent ye...[Details]
In camera and display systems, the demand for high-performance and low-power data interfaces is driving continuous technological evolution. The evolution of MIPI D-PHY and MIPI C-PHY clearly ...[Details]
Blackfin® 16-/32-bit embedded processors offer high performance, low power consumption, flexible software features, and scalability, making them suitable for converged applications such as multi-fo...[Details]
The motor is a very important component for new energy vehicles. In terms of vehicle power, pure electric vehicles use electric motors instead of traditional diesel/gasoline engines. For electric v...[Details]
Let’s first take a look at the development concept of the EVD series.
The EVD control module is specially developed for operation in extreme environments. Components that meet these requiremen...[Details]
For new energy vehicles, battery swapping is a quick and convenient way to replenish the vehicle's power, alleviating range anxiety and charging anxiety. So, for plug-in hybrid vehicles, from a tec...[Details]
This article describes how to achieve constant-pressure water supply through PID control using an Allen-Bradley PLC-5 processor in conjunction with a SAMI STAR inverter. To ensure safe and reliable...[Details]
1. Installing an industrial robot usually requires the following steps:
1. Determine the installation location: Determine the location and direction of the robot installation according to the ...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
