Ihold – Hold current: Maximum current device will pass without interruption in 23°C still air.
Itrip – Trip current: Minimum current that will switch the device from low resistance to high resistance in 23°C still air.
Vmax: Maximum continuous voltage device can withstand without damage at rated current.
Imax: Maximum fault current device can withstand without damage at rated voltage.
Pd: Power dissipated from device when in the tripped state in 23°C still air.
Ri (min.): Minimum resistance of device as supplied at 23°C unless otherwise specified.
R1(max.): Maximum resistance of device when measured one hour post reflow (SMD) or one hour post trip (radial-leaded device) at 23°C unless otherwise specified.
• Insulating material: Cured epoxy resin meeting UL 94V0 requirements
Recommended Reworking Conditions with Soldering Iron
• Soldering Iron Tip Temperature: 360°C max.
• Solder Time: 3 seconds max.
• Distance from Thermistor: 2mm min.
1011
BU-SB111164
Page 3 of 4
Data Sheet 4399
Packaging/Taping Specifications
Description
Sprocket hole pitch
Ordinate to adjacent component lead:
PTR016V0090~PTR016V0250
PTR016V0300~PTR016V1100
PTR016V1200~PTR016V1500
Device pitch:
PTR016V0090~PTR016V0600
PTR016V0700~PTR016V1400
PTR016V1500
Lead spacing
Carrier tape width
Top distance between tape edges
Hold-down tape width
Sprocket hole position
Abscissa to top:
PTR016V0090~PTR016V0600
PTR016V0700~PTR016V1500
Abscissa to plane
(straight lead)
(kinked lead)
Sprocket hole diameter
Lead protrusion
Tape thickness
Body lateral deviation
Body tape plane deviation
Reel width
Reel diameter
Arbor hole diameter
Core diameter
* See Dimensions table.
IEC
Mark
P0
P1
P1
P1
P
P
P
C
W
W0
W1
W2
H1
H1
H
H0
D0
L1
t
Δ
h
Δ
p
W3
n0
n
Dimension Tolerance
(mm)
(mm)
12.7
±0.3
3.6
4.5
7.2
12.7
25.4
38.1
*
18
3.0
12
9.0
32.2
47.5
18.0
16.0
4
1
0.9
0
0
56
340
31
80
±1.0
±1.0
±1.0
±1.0
±1.0
±1.0
--
±1.0
Max.
±1.0
+0.75/-0.5
Max.
Max.
+2/-0
±0.5
±0.2
Max.
Max.
±1.0
±1.3
Max.
±10
±1
Min.
Style 1 - PTR016V0090, PTR016V0110, PTR016V0135,
PTR016V0160-PTR016V1000
Style 2 - PTR016V1200-PTR016V1500
Reel Specifications
The only controlled copy of this Data Sheet is the electronic read-only version located on the Cooper Bussmann Network Drive. All other copies of this document are by definition uncontrolled. This bulletin is
intended to clearly present comprehensive product data and provide technical information that will help the end user with design applications. Cooper Bussmann reserves the right, without notice, to change
design or construction of any products and to discontinue or limit distribution of any products. Cooper Bussmann also reserves the right to change or update, without notice, any technical information con-
tained in this bulletin. Once a product has been selected, it should be tested by the user in all possible applications.
Life Support Policy: Cooper Bussmann does not authorize the use of any of its products for use in life support devices or systems without the express written approval of an officer of the Company. Life sup-
port systems are devices which support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result
1. Filtering function of capacitorThat is, the larger the frequency f, the smaller the impedance Z of the capacitor.
At low frequencies, the useful signal can pass smoothly because the impedance Z of ...
Matter has become really popular recently, so the question is, if we want to popularize the use of Matter, will we need to make a major change in our devices? Or can the firmware upgrade of ordinary d...
My program uses the HAL driver of STM32G431 to write the FLASH sector, but it always fails.
int save_config_params(CONFIG_PARAMS *params)
{uint32_tPAGEError;uint32_taddr;int i;FLASH_EraseInitTypeDef E...
During the simulation, when the IO port is plugged in and out, the level change should enter the interrupt, but it turns to the error below and keeps looping here. What is the reason and how to solve ...
During the simulation, when the IO port is plugged in and out, the level change should enter the interrupt, but it turns to the error below and keeps looping here. What is the reason and how to solve ...
RT1052(3) Usage of LPI2C
After learning about the first peripheral, you probably know the configuration routine of the peripheral in RT1052. It is roughly as follows.// start:
// Preparation 1: First ...
Power technology
京公网安备 11010802033920号
EEWORLD
