Ihold – Hold current: Maximum current device will pass without interruption in 23°C still air.
Itrip – Trip current: Minimum current that will switch the device from low resistance to high resistance in 23°C still air.
Vmax: Maximum continuous voltage device can withstand without damage at rated current.
Imax: Maximum fault current device can withstand without damage at rated voltage.
Pd: Power dissipated from device when in the tripped state in 23°C still air.
Ri (min.): Minimum resistance of device as supplied at 23°C unless otherwise specified.
R1(max.): Maximum resistance of device when measured one hour post reflow (SMD) or one hour post trip (radial-leaded device) at 23°C unless otherwise specified.
• Insulating material: Cured epoxy resin meeting UL 94V0 requirements
Recommended Reworking Conditions with Soldering Iron
• Soldering Iron Tip Temperature: 360°C max.
• Solder Time: 3 seconds max.
• Distance from Thermistor: 2mm min.
1011
BU-SB111164
Page 3 of 4
Data Sheet 4399
Packaging/Taping Specifications
Description
Sprocket hole pitch
Ordinate to adjacent component lead:
PTR016V0090~PTR016V0250
PTR016V0300~PTR016V1100
PTR016V1200~PTR016V1500
Device pitch:
PTR016V0090~PTR016V0600
PTR016V0700~PTR016V1400
PTR016V1500
Lead spacing
Carrier tape width
Top distance between tape edges
Hold-down tape width
Sprocket hole position
Abscissa to top:
PTR016V0090~PTR016V0600
PTR016V0700~PTR016V1500
Abscissa to plane
(straight lead)
(kinked lead)
Sprocket hole diameter
Lead protrusion
Tape thickness
Body lateral deviation
Body tape plane deviation
Reel width
Reel diameter
Arbor hole diameter
Core diameter
* See Dimensions table.
IEC
Mark
P0
P1
P1
P1
P
P
P
C
W
W0
W1
W2
H1
H1
H
H0
D0
L1
t
Δ
h
Δ
p
W3
n0
n
Dimension Tolerance
(mm)
(mm)
12.7
±0.3
3.6
4.5
7.2
12.7
25.4
38.1
*
18
3.0
12
9.0
32.2
47.5
18.0
16.0
4
1
0.9
0
0
56
340
31
80
±1.0
±1.0
±1.0
±1.0
±1.0
±1.0
--
±1.0
Max.
±1.0
+0.75/-0.5
Max.
Max.
+2/-0
±0.5
±0.2
Max.
Max.
±1.0
±1.3
Max.
±10
±1
Min.
Style 1 - PTR016V0090, PTR016V0110, PTR016V0135,
PTR016V0160-PTR016V1000
Style 2 - PTR016V1200-PTR016V1500
Reel Specifications
The only controlled copy of this Data Sheet is the electronic read-only version located on the Cooper Bussmann Network Drive. All other copies of this document are by definition uncontrolled. This bulletin is
intended to clearly present comprehensive product data and provide technical information that will help the end user with design applications. Cooper Bussmann reserves the right, without notice, to change
design or construction of any products and to discontinue or limit distribution of any products. Cooper Bussmann also reserves the right to change or update, without notice, any technical information con-
tained in this bulletin. Once a product has been selected, it should be tested by the user in all possible applications.
Life Support Policy: Cooper Bussmann does not authorize the use of any of its products for use in life support devices or systems without the express written approval of an officer of the Company. Life sup-
port systems are devices which support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result
When using orcad 10.5 pspice to simulate AD734 to implement the division function, the following problems occur at pins 10 and 13 of AD734: ERROR: [NET0075] Unconnected pin, no FLOAT property or FLOAT...
[b]Introduction to the Cyclone V FPGA Family[/b] [align=left][color=#333333][backcolor=rgb(230, 235, 238)][font=Verdana, Arial, Helvetica, sans-serif][size=12px]Altera's Cyclone V FPGAs deliver the in...
Does anyone know what software platform is used to control rehabilitation robots at home and abroad? Or what platform is used for modeling and simulation?...
2014 is about to leave. Looking back on this year, have you made greater progress? Have you been busy and fulfilled? Have you completed the goals set at the beginning of the year? [/color][/size][/fon...
1. Overview
Will passive devices
produce nonlinear intermodulation distortion? The answer is yes! Although there is no systematic theoretical analysis, it has been found in engineerin...[Details]
Remote keyless entry (RKE) systems have become popular with users, with more than 80% of new cars in North America and more than 70% in Europe equipped with RKE systems. In addition to the obvious ...[Details]
All electronic design engineers and scientists have performed electrical signal analysis, or signal analysis for short. Through this basic measurement, they can gain insight into signal details and...[Details]
A multi-point temperature control heating control system was designed using the SST89E564RC single-chip microcomputer and a new temperature measuring device. The heating system can be controlled in...[Details]
1. Introduction
At present, most lighting equipment still uses traditional energy for lighting. Making full use of solar energy as the energy supply for lighting equipment is of great si...[Details]
A standard cell
is an electrochemical
cell
used as a voltage reference standard in many electrical standards laboratories
. If properly maintained, standard cells are very stable. The ...[Details]
Overview:
This paper introduces a method of connecting a CAN-bus network with Ethernet to form a medium-sized remote monitoring/data transmission network.
CAN (Controller Area Network) is ...[Details]
1 Introduction
Building Automation System (BAS) is a distributed monitoring system (DCS) designed according to distributed information and control theory. It is the result of the mutual de...[Details]
1 Introduction
With the development of control, computer, communication, network technology, etc., a new control technology, namely fieldbus, has emerged in the field of industrial control...[Details]
my country is a big country in agriculture, grain production and consumption. Grains are a necessary condition for our nation to survive and develop. The flour processing industry will exist forever w...[Details]
Smart lighting control systems provide high controllability for various buildings and further enhance the level of green energy. They are the core products of energy conservation and digital techn...[Details]
With the continuous consumption of earth's energy and the scarcity of resources, the harm of greenhouse effect to human beings, and the serious pollution of the atmosphere to the earth, the intern...[Details]
Many battery-powered systems require a visual indicator to show when the battery needs to be replaced. LEDs are commonly used for this purpose, but they consume at least 10mA of current. This con...[Details]
The traditional display screen using 51 single-chip microcomputer to control LED dot matrix has relatively simple functions. If it is to achieve diversified functions, it often takes a lot of time ...[Details]
Nippon Electric Works and Volvo Technology Japan have developed a wireless power supply system for electric vehicles (EVs). Using this system, the two companies have successfully conducted an exper...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
