EEWORLDEEWORLDEEWORLD

Part Number

Search

5KP12CA-G

Description
tvs diodes - transient voltage suppressors 5000w vrwm=12v,bidir
CategoryDiscrete semiconductor    diode   
File Size93KB,5 Pages
ManufacturerComchip Technology
Websitehttp://www.comchiptech.com/
Environmental Compliance
Download Datasheet Parametric View All

5KP12CA-G Online Shopping

Suppliers Part Number Price MOQ In stock  
5KP12CA-G - - View Buy Now

5KP12CA-G Overview

tvs diodes - transient voltage suppressors 5000w vrwm=12v,bidir

5KP12CA-G Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerComchip Technology
Reach Compliance Codecompli
ECCN codeEAR99
Breakdown voltage nominal value14 V
Maximum clamping voltage19.9 V
Diode typeTRANS VOLTAGE SUPPRESSOR DIODE
Peak Reflow Temperature (Celsius)NOT SPECIFIED
polarityBIDIRECTIONAL
Maximum repetitive peak reverse voltage12 V
surface mountNO
Maximum time at peak reflow temperatureNOT SPECIFIED
Base Number Matches1
5000W Transient Voltage Suppressor
5KP-G Series
Stand-off Voltage: 6.8V ~ 220V
Power Dissipation: 5000 Watts
RoHS Device
Features
-Glass passivated chip.
0.052(1.32)
R-6
-Low leakage.
-Uni and Bidirection unit.
-Excellent clamping capability.
-The plastic material has UL recognition 94V-0.
-Fast response time.
0.048(1.22)
1.0(25.4)
MIN.
DIA.
0.360(9.14)
0.340(8.64)
Mechanical Data
-Case: Molded plastic R-6
-Polarity: By cathode band denotes uni-directional
device, none cathode band denotes bi-directional
device
-Weight: 2.1 grams
1.0(25.4)
MIN.
0.360(9.14)
0.340(8.64)
DIA.
Dimensions in inches and (millimeter)
Maximum Ratings and Electrical Characteristics
Rating at 25°C ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive loaded.
For capacitive load, derated current by 20%.
Parameter
Peak power dissipation with a 10/1000μs
waveform (Note 1)
Peak pulse current with a 10/1000μs waveform
(Note 1)
Power dissipation on infinite heatsink at T
L
=75°C
Peak forward surge current, 8.3ms single
half sine-wave unidirectional only (Note 2)
Maximum instantaneous forward voltage at
100A for uni-directional devices only (Note 3)
Operating junction and storage temperature
range
NTOES:
Symbol
P
PP
Value
5000
Unit
W
I
PP
See Next Table
8.0
W
P
D
W
I
FSM
500
A
V
F
3.5 / 5.0
V
T
J
, T
STG
-55 to +150
O
C
(1) Non-repetitive current pulse, per fig.5 and derated above T
A
=25 C per fig. 1.
(2) Measured on 8.3 ms single half sine wave of equivalent square wave,duty cycle=4 pulses per minute maximum.
(3) V
F
<3.5V for devices of V
BR
<200V and V
F
<
5.0V for devices of V
BR
>
201V
O
REV:B
QW-BTV08
Page 1
About the problem of LPM_ROM in Modelsim simulation of Altera
Regarding the problem of simulating LPM_ ROM in Altera with Modelsim , I am doing functional simulation and always prompts the following error: # ** Error: (vsim-7) Failed to open VHDL file "my_rom.he...
eeleader-mcu FPGA/CPLD
Capacitor step-down power supply principle and calculation formula
This type of circuit is usually used to obtain a low-cost non-isolated low-current power supply. Its output voltage can usually range from a few volts to more than 30 volts, depending on the Zener vol...
linda_xia Analog electronics
【Design Tools】Supplemental Device Guide for Monitoring Devices for Xilinx FPGAs
Advanced manufacturing techniques and smaller process geometries drive the core voltage to lower levels. This trend, combined with existing I/O standards, has led to the design of multiple voltage rai...
GONGHCU FPGA/CPLD
There's a new theory at hand that could make convolution computations more efficient
My tutor has a new theory that can improve the efficiency of convolution calculations, mainly in terms of speed and accuracy. It is better than the traditional convolution using FFT, but the applicabl...
Awakeningroom Embedded System
8051 Single Chip Microcomputer Practice and Application
Upload a classic 51 development book!...
wurongyan 51mcu
Issues on floating-point calculations on fixed-point DSP
When using fixed-point DSP for floating-point calculations, Q value calibration is used. How does DSP implement Q value? For example, in the following program,let x = 3.0, y = 3.1, then the floating-p...
weiaa1911 DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2369  64  2531  2419  2773  48  2  51  49  56 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号