EEWORLDEEWORLDEEWORLD

Part Number

Search

DFXOC2NSM3-20.0M,100/25/-/I

Description
CMOS Output Clock Oscillator, 20MHz Nom,
CategoryPassive components    oscillator   
File Size448KB,3 Pages
ManufacturerSTATEK CORPORATION
Websitehttp://www.statek.com/
Download Datasheet Parametric View All

DFXOC2NSM3-20.0M,100/25/-/I Overview

CMOS Output Clock Oscillator, 20MHz Nom,

DFXOC2NSM3-20.0M,100/25/-/I Parametric

Parameter NameAttribute value
Objectid8247624497
Reach Compliance Codecompliant
Other featuresTRAY; TR
Frequency Adjustment - MechanicalNO
frequency stability25%
Installation featuresSURFACE MOUNT
Nominal operating frequency20 MHz
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Oscillator typeCMOS
Output load15 pF
physical size7.16mm x 5.16mm x 2.05mm
Maximum supply voltage2.75 V
Minimum supply voltage2.25 V
Nominal supply voltage2.5 V
surface mountYES
maximum symmetry60/40 %
DFXO
LVDS - LVPECL & CMOS Output
20 MHz to 300 MHz
Differential Output Crystal Oscillator
DESCRIPTION
5mm x 7mm
Statek’s 5 mm x 7 mm surface mount Differential Output
Crystal Oscillator is designed for applications requiring low jitter
and ultra high frequency differential outputs in a small footprint.
Offered at frequencies from 20 MHz to 300 MHz with operation
over a temperature range of (-40°C to +105°C). No external
decoupling capacitor required with internal capacitor.
FEATURES
Low Profile
DIMENSIONS
LVDS - LVPECL- CMOS outputs available
Low phase noise - Low phase jitter
Internal 0.01µF SMD decoupling capacitor
Low Allan deviation
High Frequency Fundamental Mode Crystal
Extended Industrial temperature range
APPLICATIONS
PACKAGE DIMENSIONS
Dimension
A
B
C
(SM1)
C
(SM3/SM5)
D
E
Military & Aerospace
Avionics
Communications
Networking
TERMINATIONS
Minimum
mm
6.86
4.85
1.55
1.65
1.19
1.07
Typical
mm
7.00
5.00
1.75
1.85
1.40
1.27
Maximum
mm
7.16
5.16
1.95
2.05
1.41
1.47
Designation
SM1
SM3
SM5
Termination
Gold Plated (Pb Free)
Solder Dipped
Solder Dipped (Pb Free
)
SUGGESTED LAND PATTERN
0.100
(2.54)
0.077
(1.96)
inches
(mm)
ENABLE/DISABLE OPTIONS (T/N)
Statek offers two enable/disable options: T and N. The T-version
has a Tri-State output and continues to oscillate internally when the
output is put into the high Z state. As a result, when re-enabled,
the oscillator does not have to restart and an output with a stable
frequency resumes almost immediately. The N-version does not
have PIN 2 connected internally and so has no enable/disable
capability. The following table describes the Enable/Disable option T.
ENABLE/DISABLE OPTION T FUNCTION TABLE
0.144
(3.65)
0.070
(1.80)
0.200
(5.08)
PIN CONNECTIONS
Enable (PIN 1 High*)
Output
Oscillator
Current
Frequency Output
Oscillates
Normal
Disable (PIN 1 Low)
High Z State
Oscillates
Lower than normal
*
When PIN 1 is allowed to float, it is held high by an internal pull-up resistor.
1.
2.
3.
4.
5.
6.
(T) Enable/Disable or not connected (N)
(NC) Not Connected
Ground
LVDS - LVPECL - CMOS
LVDS - LVPECL (complementary)
Supply Voltage (V
DD
)
10196 Rev C
STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256
www.statek.com
If the temperature is too high during manual soldering of Ferroelectric's MSP430, will the data be lost or damaged?
Watch the video of the 430FR5739 series. If the temperature is too high during manual soldering, will it cause data loss, shorten the effective time, or damage the device and make it unusable? The vid...
wangfuchong Microcontroller MCU
Recruiting AE (Application Engineer) Manager - Motor Drive Direction 20-25K/month*14
Shenzhen Tingbao Technology Co., Ltd. is recruiting~!Position Title: AE (Application Engineer) Manager - Motor DriveSalary range: 20-25K/month*14Work Location: ShenzhenJob Responsibilities: 1. Respons...
Teampo Recruitment
Which mode should the USBOTG pin be set to when initializing?
I want to use the USB OTG of STM32F105VC and plan to use the master mode. When initializing USBDM and USBDP , what mode should I choose for GPIO_InitStructure.GPIO_Mode?typedef enum{ GPIO_Mode_AIN = 0...
dangelzsp stm32/stm8
Please advise, how to use inductors and capacitors to attenuate the output of the power amplifier (instead of resistor attenuation)
I have a question. I have an amplifier with an output of 100W, but the output S22 is a little bit below the standard, mainly because the bandwidth is too large. I tried 3dB attenuation with resistors ...
voco_2000 RF/Wirelessly
Makefile Problems
[i=s]This post was last edited by chenbingjy on 2016-9-19 13:28[/i] [color=#333333]There is a project file list as follows. There are 5 files in the project. In the add directory, there are add_int.c ...
chenbingjy Linux and Android
I want to use stm32f1 to measure the time interval between two rising edges
I want to use stm32f1 to measure the time interval between two rising edges...
呼呼呼呼qwe stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2389  190  2719  2193  1650  49  4  55  45  34 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号