576Mb: x18, x36 RLDRAM 3
Features
RLDRAM 3
IS49RL18320– 2 Meg x 18 x 16 Banks
IS49RL36160– 1 Meg x 36 x 16 Banks
Features
•
1066 MHz DDR operation (2133 Mb/s/ball data
rate)
•
76.8 Gb/s peak bandwidth (x36 at 1066 MHz clock
frequency)
•
Organization
– 32 Meg x 18, and 16 Meg x 36 common I/O (CIO)
– 16 banks
•
1.2V center-terminated push/pull I/O
•
2.5V V
EXT
, 1.35V V
DD
, 1.2V V
DDQ
I/O
•
Reduced cycle time (
t
RC (MIN) = 8 - 12ns)
•
SDR addressing
•
Programmable READ/WRITE latency (RL/WL) and
burst length
•
Data mask for WRITE commands
•
•
Fr
x,
DK
x#)
and output data clocks (QK
x,
QK
x#)
•
On-die DLL generates CK edge-aligned data and
•
•
•
•
•
•
•
•
64ms refresh (128K refresh per 64ms)
168-ball FBGA package
Ω
or 60
Ω
matched impedance outputs
Integrated on-die termination (ODT)
Single or multibank writes
Extended operating range (200–1066 MHz)
READ training register
Multiplexed and non-multiplexed addressing capa-
bilities
•
Mirror function
•
Output driver and ODT calibration
•
JTAG interface (IEEE 1149.1-2001)
•
Clock cycle and
t
RC timing
– 0.93ns and
t
RC (MIN) = 8ns
(RL3-2133)
– 0.93ns and
t
RC (MIN) = 10ns
(RL3-2133)
– 1.07ns and
t
RC (MIN) = 8ns
(RL3-1866)
– 1.07ns and
t
RC (MIN) = 10ns
(RL3-1866)
– 1.25ns and
t
RC (MIN) = 8ns
(RL3-1600)
– 1.25ns and
t
RC (MIN) = 10ns
(RL3-1600)
– 1.25ns and
t
RC (MIN) = 12ns
(RL3-1600)
•
Con guration
-32 Meg x 18
- 16 Meg x 36
•
Operating Temperature
– Commercial (T
C
= 0° to +95°C)
– Industrial (T
C
= –40°C to +95°C)
•
Package
– 168-ball FBGA
– 168-ball FBGA (Pb-free)
•
Revision
Options
Copyright © 2013 Integrated Silicon Solu on, Inc. All rights reserved. ISSI reserves the right to make changes to this specifica on and its products at any me without
no ce. ISSI assumes no liability arising out of the applica on or use of any informa on, products or services described herein. Customers are advised to obtain the
latest version of this device specifica on before relying on any published informa on and before placing orders for produ.ct
s
Integrated Silicon Solu on, Inc. does not recommend the use of any of its products in life support applica ons where the failure or malfunc on of the product can
reasonably be expected to cause failure of the life support system or to significantly affect its safety or effec veness. Products are not authorized for use in such
applica ons unless Integrated Silicon Solu on, Inc. receives wri en assurance to its sa sfac on, that:
a.) the risk of injury or damage has been minimized;
b.) the user assume all such risks; and
c.) poten al liability of Integrated Silicon Solu on, Inc is adequately protected under the circumstances
RLDRAM® is a registered trademark of Micron Technology, Inc.
Integrated Silicon Solution, Inc.
–
www.issi.com
–
Rev. 00B,
2/21/2013
576Mb: x18, x36 RLDRAM 3
Features
Figure 1: 576Mb RLDRAM
3 Part Numbers
Example Part Number: IS49RL18320-093EBL
-
IS49RL
Con guration
Speed Package Temp
Temperature
Con guration
32 Meg x 18
16 Meg x 36
Speed Grade
-093E
t
CK = 0.93ns (8ns
-093
-107
t
CK = 0.93ns (10ns
t
RC)
t
RC)
t
RC)
t
RC)
t
RC)
t
RC)
t
RC)
18320
36160
Commercial
Industrial
Package
168-ball FBGA
168-ball FBGA (Pb-free)
None
B
BL
-107E
t
CK = 1.07ns (8ns
t
CK = 1.07ns (10ns
-125F
t
CK = 1.25ns (8ns
-125E
t
CK = 1.25ns (10ns
-125
t
CK = 1.25ns (12ns
BGA Part Marking Decoder
Due to space limitations, BGA-packaged components have an abbreviated part marking that is di erent from the
part number. ISSI’S BGA Part Marking Decoder is available on ISSI’S Web site at www.issi.com
Integrated Silicon Solution, Inc.
–
www.issi.com
–
Rev. 00B,
2/21/2013
2
576Mb: x18, x36 RLDRAM 3
Features
Contents
General Description ......................................................................................................................................... 8
General Notes .............................................................................................................................................. 8
State Diagram .................................................................................................................................................. 9
Functional Block Diagrams ............................................................................................................................. 10
Ball Assignments and Descriptions ................................................................................................................. 12
Package Dimensions ....................................................................................................................................... 16
Electrical Characteristics – I
DD
Specifications .................................................................................................. 17
Electrical Specifications – Absolute Ratings and I/O Capacitance ..................................................................... 21
Absolute Maximum Ratings ........................................................................................................................ 21
Input/Output Capacitance .......................................................................................................................... 21
AC and DC Operating Conditions .................................................................................................................... 22
AC Overshoot/Undershoot Specifications .................................................................................................... 24
Slew Rate Definitions for Single-Ended Input Signals ................................................................................... 27
Slew Rate Definitions for Differential Input Signals ...................................................................................... 29
ODT Characteristics ....................................................................................................................................... 30
ODT Resistors ............................................................................................................................................ 30
ODT Sensitivity .......................................................................................................................................... 32
Output Driver Impedance ............................................................................................................................... 33
Output Driver Sensitivity ............................................................................................................................ 35
Output Characteristics and Operating Conditions ............................................................................................ 36
Reference Output Load ............................................................................................................................... 39
Slew Rate Definitions for Single-Ended Output Signals ..................................................................................... 40
Slew Rate Definitions for Differential Output Signals ........................................................................................ 41
Speed Bin Tables ............................................................................................................................................ 42
AC Electrical Characteristics ........................................................................................................................... 44
Temperature and Thermal Impedance Characteristics ..................................................................................... 49
Command and Address Setup, Hold, and Derating ........................................................................................... 51
Data Setup, Hold, and Derating ....................................................................................................................... 57
Commands .................................................................................................................................................... 63
MODE REGISTER SET (MRS) Command ......................................................................................................... 64
Mode Register 0 (MR0) .................................................................................................................................... 65
t
RC ............................................................................................................................................................. 66
Data Latency .............................................................................................................................................. 66
DLL Enable/Disable ................................................................................................................................... 66
Address Multiplexing .................................................................................................................................. 66
Mode Register 1 (MR1) .................................................................................................................................... 68
Output Drive Impedance ............................................................................................................................ 68
DQ On-Die Termination (ODT) ................................................................................................................... 68
DLL Reset ................................................................................................................................................... 68
ZQ Calibration ............................................................................................................................................ 69
ZQ Calibration Long ................................................................................................................................... 70
ZQ Calibration Short ................................................................................................................................... 70
AUTO REFRESH Protocol ............................................................................................................................ 71
Burst Length (BL) ....................................................................................................................................... 71
Mode Register 2 (MR2) .................................................................................................................................... 73
READ Training Register (RTR) ..................................................................................................................... 73
WRITE Protocol .......................................................................................................................................... 75
WRITE Command .......................................................................................................................................... 75
Multibank WRITE ....................................................................................................................................... 76
READ Command ............................................................................................................................................ 76
Integrated Silicon Solution, Inc.
–
www.issi.com
–
Rev. 00B,
2/21/2013
3
576Mb: x18, x36 RLDRAM 3
Features
AUTO REFRESH Command
............................................................................................................................ 78
INITIALIZATION Operation
............................................................................................................................ 80
WRITE Operation ............................................................................................................................................... 83
READ Operation ................................................................................................................................................. 87
AUTO REFRESH Operation
.............................................................................................................................. 90
Multiplexed Address Mode ............................................................................................................................... 93
Data Latency in Multiplexed Address Mode
........................................................................................... 98
REFRESH Command in Multiplexed Address Mode
............................................................................ 98
Mirror Function ...................................................................................................................................................102
RESET Operation ................................................................................................................................................. 102
IEEE 1149.1 Serial Boundary Scan (JTAG)
.................................................................................................... 103
Disabling the JTAG Feature ......................................................................................................................... 103
Test Access Port (TAP) .................................................................................................................................. 103
TAP Controller ............................................................................................................................................... 104
Performing a TAP RESET .............................................................................................................................. 106
TAP Registers .................................................................................................................................................. 106
TAP Instruction Set ........................................................................................................................................ 107
Revision History .................................................................................................................................................. 114
Rev. C, Production – 12/12 ...........................................................................................................................114
Rev. B, Advance – 1/12 .................................................................................................................................. 114
Rev. A, Advance – 6/11 .................................................................................................................................. 115
Integrated Silicon Solution, Inc.
–
www.issi.com
–
Rev. 00B,
2/21/2013
4
576Mb: x18, x36 RLDRAM 3
Features
List of Figures
Figure 1: 576Mb RLDRAM 3 Part Numbers ..................................................................................................... 2
Figure 2: Simplified State Diagram ................................................................................................................... 9
Figure 3: 32 Meg x 18 Functional Block Diagram ............................................................................................. 10
Figure 4: 16 Meg x 36 Functional Block Diagram ............................................................................................. 11
Figure 5: 168-Ball FBGA ................................................................................................................................. 16
Figure 6: Single-Ended Input Signal ............................................................................................................... 23
Figure 7: Overshoot ....................................................................................................................................... 24
Figure 8: Undershoot .................................................................................................................................... 24
Figure 9: V
IX
for Differential Signals ................................................................................................................ 25
Figure 10: Single-Ended Requirements for Differential Signals ........................................................................ 26
Figure 11: Definition of Differential AC Swing and
t
DVAC ................................................................................ 26
Figure 12: Nominal Slew Rate Definition for Single-Ended Input Signals .......................................................... 28
Figure 13: Nominal Differential Input Slew Rate Definition for CK, CK#, DKx, and DKx# .................................. 29
Figure 14: ODT Levels and I-V Characteristics ................................................................................................ 30
Figure 15: Output Driver ................................................................................................................................ 33
Figure 16: DQ Output Signal .......................................................................................................................... 38
Figure 17: Differential Output Signal .............................................................................................................. 39
Figure 18: Reference Output Load for AC Timing and Output Slew Rate ........................................................... 39
Figure 19: Nominal Slew Rate Definition for Single-Ended Output Signals ....................................................... 40
Figure 20: Nominal Differential Output Slew Rate Definition for QKx, QKx# ..................................................... 41
Figure 21: Example Temperature Test Point Location ...................................................................................... 50
Figure 22: Nominal Slew Rate and
t
VAC for
t
IS (Command and Address - Clock) ............................................... 53
Figure 23: Nominal Slew Rate for
t
IH (Command and Address - Clock) ............................................................ 54
Figure 24: Tangent Line for
t
IS (Command and Address - Clock) ...................................................................... 55
Figure 25: Tangent Line for
t
IH (Command and Address - Clock) ..................................................................... 56
Figure 26: Nominal Slew Rate and
t
VAC for
t
DS (DQ - Strobe) .......................................................................... 59
Figure 27: Nominal Slew Rate for
t
DH (DQ - Strobe) ........................................................................................ 60
Figure 28: Tangent Line for
t
DS (DQ - Strobe) ................................................................................................. 61
Figure 29: Tangent Line for
t
DH (DQ - Strobe) ................................................................................................ 62
Figure 30: MRS Command Protocol ............................................................................................................... 64
Figure 31: MR0 Definition for Non-Multiplexed Address Mode ........................................................................ 65
Figure 32: MR1 Definition for Non-Multiplexed Address Mode ........................................................................ 68
Figure 33: ZQ Calibration Timing (ZQCL and ZQCS) ....................................................................................... 70
Figure 34: Read Burst Lengths ........................................................................................................................ 72
Figure 35: MR2 Definition for Non-Multiplexed Address Mode ........................................................................ 73
Figure 36: READ Training Function - Back-to-Back Readout ............................................................................ 74
Figure 37: WRITE Command ......................................................................................................................... 75
Figure 38: READ Command ........................................................................................................................... 77
Figure 39: Bank Address-Controlled AUTO REFRESH Command ..................................................................... 78
Figure 40: Multibank AUTO REFRESH Command ........................................................................................... 79
Figure 41: Power-Up/Initialization Sequence ................................................................................................. 81
Figure 42: WRITE Burst ................................................................................................................................. 83
Figure 43: Consecutive WRITE Bursts ............................................................................................................. 84
Figure 44: WRITE-to-READ ............................................................................................................................ 84
Figure 45: WRITE - DM Operation .................................................................................................................. 85
Figure 46: Consecutive Quad Bank WRITE Bursts ........................................................................................... 86
Figure 47: Interleaved READ and Quad Bank WRITE Bursts ............................................................................. 86
Figure 48: Basic READ Burst .......................................................................................................................... 87
Figure 49: Consecutive READ Bursts (BL = 2) .................................................................................................. 88
Figure 50: Consecutive READ Bursts (BL = 4) .................................................................................................. 88
Integrated Silicon Solution, Inc.
–
www.issi.com
–
Rev. 00B,
2/21/2013
5
京公网安备 11010802033920号
EEWORLD
