IS64WV6416BLL
IS61WV6416BLL
64K x 16 HIGH-SPEED CMOS STATIC RAM
ISSI
OCTOBER 2006
®
FEATURES
• High-speed access time:
12 ns: 3.3V + 10%
15 ns: 2.5V-3.6V
• CMOS low power operation:
50 mW (typical) operating
25 µW (typical) standby
• TTL compatible interface levels
• Fully static operation: no clock or refresh
required
• Three state outputs
• Data control for upper and lower bytes
• Automotive Temperature Available
• Lead-free available
DESCRIPTION
The
ISSI
IS61/64WV6416BLL is a high-speed, 1,048,576-
bit static RAM organized as 65,536 words by 16 bits. It is
fabricated using
ISSI
's high-performance CMOS
technology. This highly reliable process coupled with inno-
vative circuit design techniques, yields access times as
fast as 12ns (3.3V + 10%) and 15ns (2.5V-3.6V) with low
power consumption.
When
CE
is HIGH (deselected), the device assumes a
standby mode at which the power dissipation can be
reduced down with CMOS input levels.
Easy memory expansion is provided by using Chip Enable
and Output Enable inputs,
CE
and
OE.
The active LOW
Write Enable (WE) controls both writing and reading of the
memory. A data byte allows Upper Byte (UB) and Lower
Byte (LB) access.
The IS61/64WV6416BLL is packaged in the JEDEC stan-
dard 44-pin TSOP-II, 44-pin 400-mil SOJ, and 48-pin mini
BGA (6mm x 8mm).
FUNCTIONAL BLOCK DIAGRAM
A0-A15
DECODER
64K x 16
MEMORY ARRAY
V
DD
GND
I/O0-I/O7
Lower Byte
I/O8-I/O15
Upper Byte
I/O
DATA
CIRCUIT
COLUMN I/O
CE
OE
WE
UB
LB
CONTROL
CIRCUIT
Copyright © 2006 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability
arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any
published information and before placing orders for products.
Integrated Silicon Solution, Inc. — www.issi.com —
1-800-379-4774
Rev. C
10/10/06
1
IS64WV6416BLL
IS61WV6416BLL
TRUTH TABLE
I/O PIN
Mode
Not Selected
Output Disabled
Read
WE
X
H
X
H
H
H
L
L
L
CE
H
L
L
L
L
L
L
L
L
OE
X
H
X
L
L
L
X
X
X
LB
X
X
H
L
H
L
L
H
L
UB
X
X
H
H
L
L
H
L
L
I/O0-I/O7
High-Z
High-Z
High-Z
D
OUT
High-Z
D
OUT
D
IN
High-Z
D
IN
I/O8-I/O15
High-Z
High-Z
High-Z
High-Z
D
OUT
D
OUT
High-Z
D
IN
D
IN
ISSI
V
DD
Current
I
SB
1
, I
SB
2
I
CC
I
CC
®
Write
I
CC
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol
V
TERM
T
STG
P
T
V
DD
Parameter
Terminal Voltage with Respect to GND
Storage Temperature
Power Dissipation
V
DD
Related to GND
Value
–0.5 to V
DD
+0.5
–65 to +150
1.5
-0.2 to +3.9
Unit
V
°C
W
V
Note:
1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at these or any other conditions above
those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect reliability.
OPERATING RANGE (V
DD
)
Range
Commercial
Industrial
Automotive
Ambient Temperature
0°C to +70°C
–40°C to +85°C
–40°C to +125°C
V
DD
(15 ns)
2.5V-3.6V
2.5V-3.6V
2.5V-3.6V
V
DD
(12 ns)
3.3V + 10%
3.3V + 10%
3.3V + 10%
Integrated Silicon Solution, Inc. — www.issi.com —
1-800-379-4774
Rev. C
10/10/06
3
IS64WV6416BLL
IS61WV6416BLL
DC ELECTRICAL CHARACTERISTICS
(Over Operating Range)
V
DD
= 2.5V-3.6V
Symbol
V
OH
V
OL
V
IH
V
IL
I
LI
I
LO
Note:
1.
V
IL
(min.) = –0.3V DC; V
IL
(min.) = –2.0V AC (pulse width - 2.0 ns). Not 100% tested.
V
IH
(max.) = V
DD
+ 0.3V DC; V
IH
(max.) = V
DD
+ 2.0V AC (pulse width - 2.0 ns). Not 100% tested.
ISSI
Test Conditions
V
DD
= Min., I
OH
= –1.0 mA
V
DD
= Min., I
OL
= 1.0 mA
Min.
2.3
—
2.0
–0.3
GND
≤
V
IN
≤
V
DD
GND
≤
V
OUT
≤
V
DD
, Outputs Disabled
–2
–2
Max.
—
0.4
V
DD
+ 0.3
0.8
2
2
Unit
V
V
V
V
µA
µA
®
Parameter
Output HIGH Voltage
Output LOW Voltage
Input HIGH Voltage
Input LOW Voltage
(1)
Input Leakage
Output Leakage
DC ELECTRICAL CHARACTERISTICS
(Over Operating Range)
V
DD
= 3.3V + 10%
Symbol
V
OH
V
OL
V
IH
V
IL
I
LI
I
LO
Note:
1.
V
IL
(min.) = –0.3V DC; V
IL
(min.) = –2.0V AC (pulse width - 2.0 ns). Not 100% tested.
V
IH
(max.) = V
DD
+ 0.3V DC; V
IH
(max.) = V
DD
+ 2.0V AC (pulse width - 2.0 ns). Not 100% tested.
Parameter
Output HIGH Voltage
Output LOW Voltage
Input HIGH Voltage
Input LOW Voltage
(1)
Input Leakage
Output Leakage
Test Conditions
V
DD
= Min., I
OH
= –4.0 mA
V
DD
= Min., I
OL
= 8.0 mA
Min.
2.4
—
2
–0.3
Max.
—
0.4
V
DD
+ 0.3
0.8
2
2
Unit
V
V
V
V
µA
µA
GND
≤
V
IN
≤
V
DD
GND
≤
V
OUT
≤
V
DD
, Outputs Disabled
–2
–2
4
Integrated Silicon Solution, Inc. — www.issi.com —
1-800-379-4774
Rev. C
10/10/06
IS64WV6416BLL
IS61WV6416BLL
POWER SUPPLY CHARACTERISTICS
(1)
(Over Operating Range)
Symbol Parameter
I
CC
V
DD
Dynamic Operating
Supply Current
Test Conditions
V
DD
= Max.,
I
OUT
= 0 mA, f = f
MAX
Options
COM
.
IND
.
AUTO
ISSI
-12 ns
Min. Max.
—
—
—
—
—
—
—
—
—
—
—
35
45
60
20
5
5
5
20
50
75
6
-15 ns
Min. Max.
—
—
—
—
—
—
—
—
—
—
—
30
40
50
20
5
5
5
20
50
75
6
uA
Unit
mA
®
typ.
(2)
I
CC
1
Operating Supply
Current
I
SB
2
CMOS Standby
Current (CMOS Inputs)
V
DD
= Max.,
Iout = 0mA, f = 0
V
DD
= Max.,
CE
≥
V
DD
– 0.2V,
V
IN
≥
V
DD
– 0.2V, or
V
IN
≤
0.2V, f = 0
COM
.
IND
.
AUTO
COM
.
IND
.
AUTO
mA
typ.
(2)
Note:
1. At f = f
MAX
, address and data inputs are cycling at the maximum frequency, f = 0 means no input lines change.
2. Typical values are measured at V
DD
=2.5V, T
A
=25
o
C. Not 100% tested.
CAPACITANCE
(1)
Symbol
C
IN
C
OUT
Parameter
Input Capacitance
Input/Output Capacitance
Conditions
V
IN
= 0V
V
OUT
= 0V
Max.
6
8
Unit
pF
pF
Note:
1. Tested initially and after any design or process changes that may affect these parameters.
Integrated Silicon Solution, Inc. — www.issi.com —
1-800-379-4774
Rev. C
10/10/06
5
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
