Operating Temperature Range ......................... -40°C to +125°C
Storage Temperature Range ............................ -65°C to +150°C
Lead Temperature (soldering, 10s) ................................. +300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Electrical Characteristics
(V
CC
= full range, T
A
= -40°C to +125°C, unless otherwise noted. Typical values are at V
CC
= +5V for L/M versions, V
CC
= +3.3V for
T/S versions, V
CC
= +3V for R version, V
CC
= +2.5V for Z version, and T
A
= +25°C.) (Note 1)
PARAMETER
V
CC
Range
SYMBOL
CONDITIONS
T
A
= 0°C to +70°C
T
A
= -40°C to +105°C
T
A
= -40°C to
Supply Current
I
CC
+85°C
T
A
= +85°C to
+105°C
MAX671_L
V
CC
< 5.5V, MAX671_L/M
V
CC
< 3.6V, MAX671_R/S/T/Z
V
CC
< 5.5V, MAX671_L/M
V
CC
< 3.6V, MAX671_R/S/T/Z
T
A
= +25°C
T
A
= -40°C to +85°C
T
A
= +85°C to +105°C
T
A
= +25°C
MAX671_M
T
A
= -40°C to +85°C
T
A
= +85°C to +105°C
T
A
= +25°C
MAX671_T
Reset Threshold
V
TH
MAX671_S
T
A
= -40°C to +85°C
T
A
= +85°C to +105°C
T
A
= +25°C
T
A
= -40°C to +85°C
T
A
= +85°C to +105°C
T
A
= +25°C
MAX671_R
T
A
= -40°C to +85°C
T
A
= +85°C to +105°C
T
A
= +25°C
MAX671_Z
Reset-Threshold Tempco
V
CC
to Reset Delay (Note 2)
Reset Active Timeout Period
V
CC
= V
TH
to (V
TH
- 100 mV)
T
A
= -40°C to +85°C
T
A
= +85°C to +125°C
140
100
T
A
= -40°C to +85°C
T
A
= +85°C to +105°C
4.56
4.50
4.40
4.31
4.25
4.16
3.04
3.00
2.92
2.89
2.85
2.78
2.59
2.55
2.50
2.28
2.25
2.21
30
20
240
460
840
2.32
2.63
2.93
3.08
4.38
4.63
MIN
1.0
1.2
16
12
TYP
MAX
5.5
5.5
35
30
75
75
4.70
4.75
4.86
4.45
4.50
4.56
3.11
3.15
3.23
2.96
3.00
3.08
2.66
2.70
2.76
2.35
2.38
2.45
ppm/°C
µs
ms
V
µA
UNITS
V
www.maximintegrated.com
Maxim Integrated
│
2
MAX6711L/M/R/S/T/Z,
MAX6712L/M/R/S/T/Z,
MAX6713L/M/R/S/T/Z
Electrical Characteristics (continued)
4-Pin SC70 Microprocessor
Reset Circuits with Manual Reset Input
(V
CC
= full range, T
A
= -40°C to +125°C, unless otherwise noted. Typical values are at V
CC
= +5V for L/M versions, V
CC
= +3.3V for
T/S versions, V
CC
= +3V for R version, V
CC
= +2.5V for Z version, and T
A
= +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
V
CC
= V
TH
min, I
SINK
= 1.2mA,
RESET Output-Voltage Low
(MAX6711/MAX6713)
V
OL
MAX6711R/S/T/Z, MAX6713R/S/T/Z
V
CC
= V
TH
min, I
SINK
= 3.2mA,
MAX6711L/M, MAX6713L/M
V
CC
> 1.0V, I
SINK
= 50µA
V
CC
> V
TH
max, I
SOURCE
= 500µA,
RESET Output-Voltage High
(MAX6711)
V
OH
MAX6711R/S/T/Z
V
CC
> V
TH
max, I
SOURCE
= 800µA,
MAX6711L/M
V
CC
= V
TH
max, I
SINK
= 1.2mA,
MAX6712R/S/T/Z
V
CC
= V
TH
max, I
SINK
= 3.2mA, MAX6712L/M
V
OH
1.8V < V
CC
< V
TH
min, I
SOURCE
= 150µA
V
CC
> V
TH
, RESET deasserted
V
IL
V
IH
10
1
100
200
20
0.3 x V
CC
0.7 x V
CC
0.8 x V
CC
1
0.8 x V
CC
V
V
CC
x 1.5
0.3
V
0.4
V
µA
V
kW
µs
ns
ns
MIN
TYP
MAX
0.3
0.4
0.3
V
UNITS
RESET Output-Voltage Low
(MAX6712)
RESET Output-Voltage High
(MAX6712)
RESET Open-Drain Output-
Leakage Current
MR Input Threshold
MR Pull-Up Resistance
MR Minimum Pulse Width
MR Glitch Immunity
V
OL
MR to Reset Delay
Note 1:
Production testing done at T
A
= +25°C; limits over temperature guaranteed by design only.
Note 2:
RESET
output for MAX6711/MAX6713; RESET output for MAX6712.
www.maximintegrated.com
Maxim Integrated
│
3
MAX6711L/M/R/S/T/Z,
MAX6712L/M/R/S/T/Z,
MAX6713L/M/R/S/T/Z
Typical Operating Characteristics
4-Pin SC70 Microprocessor
Reset Circuits with Manual Reset Input
(V
CC
= full range, T
A
= -40°C to +125°C, unless otherwise noted. Typical values are at V
CC
= +5V for L/M versions, V
CC
= +3.3V for
T/S versions, V
CC
= +3V for R version, V
CC
= +2.5V for Z version, and T
A
= +25°C.)
SUPPLY CURRENT vs. TEMPERATURE
(NO LOAD)
MAX6711/12/13 toc01
MAX671_R/S/T/Z
POWER-DOWN RESET DELAY vs. TEMPERATURE
MAX6711/12/13-TOC2
POWER-DOWN RESET DELAY (µs)
POWER-DOWN RESET DELAY (µs)
V
OD
= 10mV
60
V
OD
= 20mV
40
V
OD
= 10mV
SUPPLY CURRENT (µA)
MAX671_L/M, V
CC
= 5V
10
MAX671 _Z, V
CC
= 2.5V
MAX671 _R/S/T, V
CC
= 3.3V
5
MAX671 _L/M/R/S/T/Z, V
CC
= 1V
0
150
120
90
60
30
0
-40 -20
V
OD
= 100mV
V
OD
= 200mV
0
20 40 60 80
TEMPERATURE (°C)
100 120
V
OD
= 20mV
20
V
OD
= 100mV
V
OD
= 200mV
0
20
40
60
80
100 120
TEMPERATURE (°C)
-40 -20
0
20
40
60
80
100 120
0
-40 -20
TEMPERATURE (°C)
MAX6711/12/13-TOC4
V
TH
= 4.63V
POWER-UP RESET TIMEOUT (ms)
RESET THRESHOLD (V)
275
MAX671_ R/S/T/Z
250
1.000
0.999
225
MAX671_ L/M
0.998
200
-40 -20
0
20
40
60
80
100 120
-40 -20
0
20
40
60
80
100 120
TEMPERATURE (°C)
TEMPERATURE (°C)
www.maximintegrated.com
Maxim Integrated
│
4
MAX6711/12/13-TOC5
300
POWER-UP RESET TIMEOUT vs.
TEMPERATURE
1.001
RESET THRESHOLD vs.
TEMPERATURE
MAX6711/12/13-TOC3
15
80
MAX671_L/M
POWER-DOWN RESET DELAY vs. TEMPERATURE
180
MAX6711L/M/R/S/T/Z,
MAX6712L/M/R/S/T/Z,
MAX6713L/M/R/S/T/Z
Pin Description
PIN
1
NAME
GND
RESET
(MAX6711/
MAX6713)
2
RESET
(MAX6712)
RESET output remains high while
V
CC
is below the reset threshold, and
for at least 140ms after V
CC
rises
above the reset threshold.
Manual Reset Input. RESET (RESET)
remains asserted as long as
MR
is
low, and for at least 140ms after
MR
is
deasserted. This active-low input has
an internal 20kW
(typ) pull-up resistor.
It can be driven from a TTL- or
CMOS- logic line, or shorted to ground
with a switch. Leave open or connect
to V
CC
if unused.
Supply Voltage (+5.0V, +3.3V, +3.0V,
or +2.5V)
Ground
RESET
output remains low while
V
CC
is below the reset threshold, and
for at least 140ms after V
CC
rises
above the reset threshold.
FUNCTION
4-Pin SC70 Microprocessor
Reset Circuits with Manual Reset Input
V
CC
MAX6711
RESET
MR
GND
R1
100k
Figure 2.
RESET
Valid to V
CC
= Ground Circuit
3
MR
least 140ms after V
CC
has risen above the reset thresh-
old. The MAX6713 uses an open-drain output, and
the MAX6711/MAX6712 have a push-pull output stage.
Connect a pull-up resistor on the MAX6713's
RESET
output to any supply between 0 and 6V.
Manual Reset Input
4
V
CC
400
MAXIMUM TRANSIENT DURATION (µs)
320
240
160
T
A
= +25C
MAX671_L/M
80
0
MAX671_R/S/T/Z
1
10
100
1000
Many µP-based systems require manual reset capabili-
ty, allowing the operator, a test technician, or external
logic circuitry to initiate a reset. Reset remains asserted
while MR is low, and for at least 140ms after
MR
returns
high. This input has an internal 20kW pullup resistor, so
it can be left open if it is not used.
MR
can be driven
with TTL- or CMOS-logic levels, or with open-drain/col-
lector outputs. To create a manual reset function, con-
nect a normally open momentary switch from
MR
to
ground; external debounce circuitry is not required. If
MR
is driven from long cables or if the device is used in
a noisy environment, connecting a 0.1µF capacitor from
MR
to ground provides additional noise immunity.
Applications Information
Negative-Going V
CC
Transients
In addition to issuing a reset to the µP during power-up,
power-down, and brownout conditions, the MAX6711/
MAX6712/MAX6713 are relatively immune to short-dura-
tion negative-going V
CC
transients (glitches).
Figure 1 shows typical transient duration vs. reset com-
parator overdrive, for which the MAX6711/MAX6712/
MAX6713 do
not
generate a reset pulse. The graph was
generated using a negative-going pulse applied to V
CC
,
starting 0.5V above the actual reset threshold and end-
ing below it by the magnitude indicated (reset compar-
ator overdrive). The graph indicates the maximum pulse
width a negative-going V
CC
transient can have without
causing a reset pulse. As the magnitude of the transient
increases (goes farther below the reset threshold), the
RESET COMPARATOR OVERDRIVE, V
TH
- V
CC
(mV)
Figure 1. Maximum Transient Duration Without Causing a
Reset Pulse vs. Reset Comparator Overdrive
Detailed Description
Reset Output
A microprocessor's (µP's) reset input starts the µP in a
known state. The MAX6711/MAX6712/MAX6713 assert
reset to prevent code-execution errors during power-
up, power-down, or brownout conditions. They assert a
reset signal whenever the V
CC
supply voltage declines
below a preset threshold, keeping it asserted for at
As shown in the figure below, when looking at the information of a sensor conditioning chip, it is recommended to use JFET or NPN transistors to build a power supply voltage conversion circuit in the ...
[Activity Purpose] Recently, a post by teacher quanzx, "[url=https://bbs.eeworld.com.cn/thread-86444-1-1.html]A Design by an Expert[/url]", has attracted much attention from netizens, triggering a ser...
Embedded systems are the replacement products of computer technology, communication technology, semiconductor technology, microelectronics technology, voice and image data transmission technology, and...[Details]
Digital-to-analog converters (ADCs) provide the critical conversion of analog signals to digital signals in many systems. They perform amplitude quantization of an analog input signal to a binary fini...[Details]
Controller Area Network (CAN) is a type of fieldbus. It is a serial communication network that effectively supports distributed control or real-time control and is recognized as one of the most pro...[Details]
Basic principles of simulation
Simulation is a technology used in the field of embedded system development. It can bring system developers the controllability and visibility needed to integra...[Details]
To ensure the success of China's TD-SCDMA network commercialization, operators and equipment suppliers need to conduct a large number of tests on networked equipment, among which RF testing is...[Details]
0 Introduction to the direct method of feedback linearization based on dynamic equilibrium state theory
The basic idea of the direct method of feedback linearization based on dynamic equilib...[Details]
Compared with traditional light sources, light-emitting diodes (LEDs) have many advantages, such as low operating voltage, high energy efficiency, small size and directional light. They can provide...[Details]
summary
Theoretically explains how to set up a PFC boost regulator using a current sensing transformer with the UCC3817 control IC.
1. Schematic
The schematic diagram is show...[Details]
A well-designed electronic load is not designed just for use in the lab; it should be carefully designed and built to test actual power systems. This is true for military portable systems, such as ...[Details]
1. Introduction
The UCC28051 reference design is a 100W offline AC/DC voltage converter with power factor correction (PFC). This power module design is intended to illustrate how to proper...[Details]
introduction
Every friend who has been in contact with PC since the 286 era must have deeply experienced the convenience brought to our lives and work by the leaps and bounds of comput...[Details]
1 Introduction to suction laminating machine
Suction laminating machine is a kind of woodworking machinery, which can realize the laminating function of wood boards and other materials. It i...[Details]
introduction
Traditional electric actuators are easy to use and save investment, and have been widely used in production process control systems in the fields of electricity, metallurgy, petro...[Details]
Battery system architecture
For many years, nickel-cadmium batteries and later nickel-metal hydride battery technology have dominated the market. Lithium batteries have only entered ...[Details]
Nowadays, video conferencing has become a situation where multiple manufacturers supply various high-definition products. The technology of high-definition products has greatly matured, the cost h...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
