Operating Temperature Range ...........................-40°C to +85°C
Storage Temperature Range .............................-65°C to +150°C
Junction Temperature ......................................................+150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V
CC
= full range, T
A
= -40°C to +85°C, unless otherwise noted. Typical values are at T
A
= +25°C and V
CC
= 3V.) (Note 1)
PARAMETER
V
CC
Operating Range
SYMBOL
CONDITIONS
T
A
= 0°C to +70°C
T
A
= -40°C to +85°C
I
CC
MAX6375/76/77 only, V
CC
= 3.0V for V
TH
≤
2.93V,
V
CC
= 3.2V for V
TH
> 2.93V, no load
V
CC
= 5.5V, no load
T
A
= +25°C
Voltage Threshold
V
TH
Table 1
T
A
= -40°C to +85°C
Voltage Threshold Tempco
Propagation Delay
OUT
Output Voltage
(MAX6375/MAX6377/
MAX6378/MAX6380)
OUT
Output Voltage
(MAX6375/MAX6377)
∆V
TH
/°C
V
CC
= (V
TH
+ 100mV) to (V
TH
- 100mV)
V
CC
= (V
TH
- 100mV) to (V
TH
+ 100mV)
V
OL
I
SINK
= 1.6mA, V
CC
> 2.1V,
OUT
asserted
I
SINK
= 100µA, V
CC
≥
1.2V,
OUT
asserted
I
SOURCE
= 500µA, V
CC
= 3.2V, MAX6375 only
V
OH
I
SOURCE
= 800µA, V
CC
= 4.5V, V
TH
≤
4.38V
I
SOURCE
= 800µA, V
CC
= V
TH(MAX)
, V
TH
≥
4.5V
V
OH
OUT Output Voltage
(MAX6376/MAX6379)
V
OL
I
SOURCE
= 500µA, V
CC
≥
2.1V, OUT asserted
I
SOURCE
= 50µA, V
CC
≥
1.2V, OUT asserted
I
SINK
= 1.2mA, V
CC
≥
3.2V, OUT not asserted,
MAX6376 only
I
SINK
= 3.2mA, V
CC
≥
4.5V, OUT not asserted,
V
TH
≤
4.38V
I
SINK
= 3.2mA, V
CC
= V
TH(MAX)
, V
TH
≥
4.5V
Voltage Threshold
Hysteresis
Open-Drain
OUT
Output
Leakage Current
Note 1:
Production tested at +25°C only. Overtemperature limits are guaranteed by design, not production tested.
I have a device made with STM32F103VC. I used to use injection mode (all three ADs were used). The sampling zero drift was very small, basically within 1 LSB (most of them were 0). Now I use DMA mode ...
After writing the address to 430, the power is turned off, and then the power is turned on again, a small part of the address will change. What's going on? ? ? ?...
[i=s]This post was last edited by dontium on 2015-1-23 12:46[/i]Full version in Chinese and English : Texas Instruments Industrial Automation Solutions - Motor Control/Drives (First Half of 2011)TI's ...
I'm working on [img]k7 multiboot with w25q64 (spi flash), the system is win7, the platform is ise 14.5. I can download a mcs file synthesized from a bit file, but when I download an mcs file synthesiz...
[size=4][color=red]I like password locks, but after seeing many designs, few people mentioned the hardware design of password locks. Here I would like to discuss with experts: What is the design idea ...
Traditional broadcasting systems generally need to be operated manually at a fixed time, and can only realize one-way broadcasting with few functions. Traditional bell ringing equipment has a singl...[Details]
Hardware designers have begun to adopt FPGA technology in high-performance DSP designs because it can provide 10-100 times faster computing than PC-based or microcontroller-based solutions. Previou...[Details]
This program is written to simulate the serial port hardware mechanism. When used, a timed interrupt can be set with a time interval of 1/4 baud rate. The receiving function is called once for ea...[Details]
1 Introduction
A wide variety of communication cables and control cables are widely used in various instruments and control equipment. Whether the cable is well-conducted and
whether
th...[Details]
1. Circuit composition
The whole circuit consists of two parts:
1. Power saving control circuit
As shown in the figure below. Including delay circuit and drive circuit.
(1) Delay ci...[Details]
1. Introduction
With the growth of parking demand, the scale of parking lots is becoming larger and larger. A lot of research has been done on intelligent parking lots in China, but most of th...[Details]
Converged processors meet scalability requirements
In current embedded system design, solutions based on MCU, DSP, FPGA and ASIC account for more than 90% of the market share. These solutions ...[Details]
There are three types of mobile TV: one is based on analog TV broadcasting network, another is based on mobile communication network, and the other is based on digital broadcasting network. The f...[Details]
This paper designs a dot matrix LED text display screen that is easy to update, expandable, and low-cost. The way to reduce costs is
① Use the Bluetooth data transmission function of mobile ph...[Details]
introduction
For the voltage regulator modules (VRMs) that power the latest computer central processing units (CPUs), power supply designers have historically used multiphase interleaved b...[Details]
DSP (digital signal processor) is used more and more frequently in today's engineering applications. There are three main reasons for this: first, it has powerful computing power and is capable of ...[Details]
1. System Structure
This system is a simulation system of indoor air-conditioning temperature/humidity control system. The data acquisition and control center collects temperature/humidity...[Details]
MediaTek (2454) announced the acquisition of F-MStar (3697) and attracted the attention of IC design industry. This morning, Gartner Semiconductor Industry Research Director Hong Cenwei analyzed ...[Details]
PV inverter manufacturer SMA has launched its first DC arc fault circuit interrupter (AFCI) PV inverter and has received UL certification.
The new SunnyBoy AFCI inverter models include 3000-US...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
