Standard Frequencies – see Page 5 for common frequencies.
* Check with factory for availability of frequencies not listed.
Applications
IoT and IIoT Applications
Wireless Communications
FPGA/Microcontrollers
USB Interfaces
Computer Peripherals
Portable Equipment
Test and Measurement
M2M Communications
Broadband Access
Description
CTS Model 407 incorporates a high Q quartz resonator and is ideal for supporting a wide range of commercial and
industrial applications.
Ordering Information
Model
407
Mode of
Os ci l l a ti on
F
T ol era nce
@ +25°C
3
T em pera ture Sta bi l i ty/T em pera ture Ra ng e
5
Loa d
Ca pa ci ta nce
D
F requency
[ MHz ]
XXXMXXXX
Mode
Code
Fundamental
F
3rd Overtone
T
Code
- 20°C
1
X
2
3
5
Code
1
X
2
3
Tolerance
±10ppm
±15ppm
±20ppm
±30ppm
Stability Code
to +70°C - 30°C
±10ppm
R
±15ppm
Y
±20ppm
N
±30ppm
4
±50ppm
8
Stability Code
to +85°C - 40°C
±10ppm
-
±15ppm
W
±20ppm
6
±30ppm
7
±50ppm
9
Stability
to +85°C
-
±15ppm
±20ppm
±30ppm
±50ppm
Code
Frequency
Frequency
1
Code Capacitance Code Capacitance
8pF
18pF
K
D
9pF
20pF
J
E
10pF
24pF
A
F
12pF
30pF
L
G
16pF
Series
C
S
Notes:
1] Frequency is recorded with 3 leading digits before the "M" and 4 significant digits after the "M" [including zeroes]. (Ex. XXXMXXXX [016M3840],
There are frequencies with significant digits after the "M" that exceed the 4 digits. The remaining digits will be truncated from the CTS part
number, but the factory will calibrate to the full frequency desired. Examples below; P/N Frequency = Actual Frequency
13M5537 = 13.553750MHz
14M3181 = 14.318180MHz
16M6666 = 16.666670MHz
28M6363 = 28.636360MHz
N ot a l l perf orm a nce com bi na ti ons a nd f requenci es m a y be a va i l a bl e.
Conta ct your l oca l CT S Repres enta ti ve or CT S Cus tom er Servi ce f or a va i l a bi l i ty.
This product is specified for use only in standard commercial applications. Supplier disclaims all express and implied warranties and liability in connection with any use of this
product in any non-commercial applications or in any application that may expose the product to conditions that are outside of the tolerances provided in its specification.
Comparison of three basic amplifier circuits1. The input impedance and output impedance range from tens of ohms to hundreds of kiloohms. What causes this? How to select the application based on the in...
There are relatively few book resources now, I hope you can give me some advice, thank you, for example, how to make the open and exit functions under the file menu and display them on the smartphone ...
Work location: Pukou District, Nanjing, Jiangsu Province. Interested parties please send your resume to [email]232092178@qq.com[/email] 1. Job responsibilities of embedded development engineer: 1. Fam...
The previous design missed the MCU power supply. To save energy, MSP430 is used with a power supply voltage of 2.6V. In addition, a 3.3V voltage output is required. Change the design as follows: 1. Se...
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
introduction
With the continuous optimization of surface mount technology (SMT) and the rapid development of chip component manufacturing technology, the application of chip mounters in the el...[Details]
This article discusses how to wake up a touch-sensitive device such as a tablet without touching the device, using basic gesture recognition and novel proximity sensors. The article discusses the p...[Details]
1. Introduction
Automobile pollution is one of the most important issues that people are most concerned about and need to solve urgently. As an important method for detecting automobile exhau...[Details]
0. Introduction
In daily life, we often see some special-purpose vehicles. When these vehicles pass through intersections, they often obtain the right of way at intersections by temporarily op...[Details]
In this article, the high-performance DSP developed by TI can be used as an effective confidentiality method if it is applied to PC encryption cards.
As an effective network security solution,...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
Contact resistance
is the resistance to current flow through a closed pair of contacts. This type of measurement is performed on devices such as connectors,
relays
, and switches. The...[Details]
1 Introduction to HART Protocol
HART (Highway Addressable Remote Transducer), an open communication protocol for addressable remote sensor high-speed channels, was launched by Rosemen in the U...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
Continuity test
A variety of devices need to be checked for continuity, including cable assemblies, printed circuit boards, and connectors to ensure that these components have the expected contin...[Details]
Capacitors
are basic components in various electronic devices and are widely used for bypassing, coupling,
filtering
, tuning, etc. in electronic circuits. However, to use capacitors,...[Details]
introduction
At present, measuring instruments are developing towards networking, and each individual embedded instrument will become a node on the Internet. This system realizes the network...[Details]
Fruit planting is an important part of China's agricultural development, and fruit tree pest control operations are becoming more and more important. At present, the overall level of pesticide applica...[Details]
Our flight had just begun to descend when a gentleman sitting next to me turned to talk to me about engineering—he had seen me reading an engineering journal. The gentleman next to me said that he ...[Details]
Discrete Device
京公网安备 11010802033920号
EEWORLD
