EEWORLDEEWORLDEEWORLD

Part Number

Search

BV212A1/240VAC

Description
Power/Signal Relay
CategoryMechanical and electronic products    relay   
File Size695KB,4 Pages
ManufacturerBarnbrook Systems Limited
Download Datasheet Parametric View All

BV212A1/240VAC Overview

Power/Signal Relay

BV212A1/240VAC Parametric

Parameter NameAttribute value
Objectid1931144594
Reach Compliance Codeunknown
ECCN codeEAR99
Manufacturer's serial numberWB
Relay typePOWER/SIGNAL RELAY
DATA SHEET
RELAY
The Walton Bee relay is a range of high quality, long life
products with high load capacity, Flexible design allows one
to four pole, each of NO, NC or CO mode in up to 30
combinations. Each pole has a maximum current capacity of
20 amps. The maximum voltage/pole is 550V rms,
The units are mechanically Interchangeable with the Walton
Bee 'M' range and the Arrow '28' series but with M4 terminals.
Key Features
Adjustable stop ensures compliance with BRB Spec. TDE/G/77D/71
for vibration resistance and use with voltages up to 250V rms on Rail
rolling stock. Coils in this range are fully encapsulated.
Coils can be fitted with diodes for voltage surge suppression, for ac/dc
operation, or for reverse polarity protection, as required.
Type WB
Specification
Electrical
Coil Power
Pull-in Voltage.
3 watts dc or 6V A
dc: less than 50% nominal Voltage
ac: less than 75% nominal Voltage.
Drop-out Voltage
dc is greater than 0.1 (or 10%) nominal Voltage.
Pull-in Voltage
Non standard dc values
±5%
Dielectric strength
>2500 V rms
Insulation Resistance
>100 Megohms at 500 V dc
Clearances between live parts (except at contact) and between live parts and earth >6mm
Creepage distances
>10mm
Maximum current
20 Amps continuous per contact
Life
10
6
at 2 ops/minute, 10% on/off ratio
240 V ac
20 amps unity power factor
15 amps 0.8 power factor
10 amps 0.6 power factor -Silver alloy contacts
recommended
415 V ac
10 amps unity power factor
24 V dc
16 amps resistive
For incandescent filament loads the current ratings are reduced to 20% of the nominal values
110 V dc
4 amps resistive
24 V dc
0.5 H 3 amps
Environmental and Physical
Mounting
Terminal Screws
Temperature range
Mechanical Life
Weight
Horizontal plane, or vertical plane with contact springs vertical
M4
-10
o
C to +50
o
C
>10
6
140- 190 gms
See sheet 3
For Barnbrook Catalogue numbers see Sheet 2.
For equivalent BR Catalogue numbers See Sheet 4
Dimensions
Ordering Information
Data Sheet No
DSRELWB-0305
Sheet 1 of 4
Design authority and manufacture by Barnbrook Systems Limited
Barnbrook Systems reserves the right to alter specifications and design without notice
BARNBROOK SYSTEMS LIMITED, 25 FAREHAM PARK ROAD, HAMPSHIRE, PO15 6LD
TEL NO: +44(0)1329 847722 FAX: +44(0)1329 844132 E-mail:
sales@barnbrook.co.uk
www.barnbrook.com
STM32F103 variable definition
The definition statements in the .h file of an STM32 file are: #define LED_SEG0 PBout(0) #define LED_SEG1 PBout(1) . . . . #define LED_SEG15 PBout(15) The values assigned in its .c file are: LED_SEG0=...
forever1314 stm32/stm8
Some doubts about shutting down interrupts
After the MCU turns off interrupts, if an interrupt occurs, will it be discarded or latched? If it is latched, then if two interrupts of the same type come (for example, both are external interrupts w...
月痕 Embedded System
Quartus II setup problem
has two settings that I don't know how to fix. Because I couldn't restore them after the previous operation? ? ? (1) How can I changeback to the original ? I have been looking for this setting for a l...
wengzf FPGA/CPLD
ucos critical protection problem
I would like to ask for advice onOS_ENTER_CRITICAL() andOS_EXIT_CRITICAL()If uCos-II is running multiple tasks, and the highest priority task writes some global variables (such as assignment or additi...
greedangel Real-time operating system RTOS
Looking for operational amplifier video learning materials
I am not familiar with op amps. Although I feel that I understand the theory, I just feel that I don't have the practical skills. Therefore, I want to find some video materials about op amps. I would ...
yhye2world Discrete Device
The host computer written in MFC receives UDP packets via Ethernet. Why can't it read the data in the buffer?
I used LM3S8962 to write a program to send UDP messages using Ethernet. It can correctly receive UDP messages from the host computer and can also send UDP messages. The messages sent by LM3S8962 can b...
huangzhechen Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 839  1969  1285  1512  1797  17  40  26  31  37 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号