monitor identification, including recovery to DDC1
- Low power CMOS technology
- 1 mA typical active current
- 10 uA standby current typical at 5.5V
- 2-wire serial interface bus, I
2
C compatible
- 100Khz (2.5V) and 400Khz (5V) compatibility
- Self-timed write cycle (including auto-erase)
- Hardware write-protect pin
- Page-write buffer for up to eight bytes
- 1,000,000 erase/write cycles
- Data retention > 40 years
- 8-pin PDIP and SOP packages
- Available for extended temperature ranges
Commercial (C): 0°C to +70°C
Industrial (I): -40°C to +85°C
(Preliminary)
General Description
The AM24LC21 is a 128 x 8-bit dual-mode
Electrically Erasable PROM. This device is
designed for use in applications requiring storage
and serial transmission of configuration and control
information. Two modes of operation have been
implemented: transmit only mode and bi-directional
mode. Upon power-up, the device will be in the
transmit only mode, sending a serial bit stream of
the memory array contents, clocked by the VCLK
pin. A valid high to low transition on the SCL pin will
cause the device to enter the bi-directional mode,
with byte selectable read/write capability of the
memory array. The AM24LC21 is available in a
standard 8-pin PDIP and SOP package in both
commercial and industrial temperature ranges.
Pin Assignments
(Top View)
NC
NC
WP
VSS
1
2
3
4
8
7
6
5
VCC
VCLK
SCL
SDA
NC
NC
WP
VSS
1
2
3
4
(Top View)
8
7
6
5
VCC
VCLK
SCL
SDA
Pin Descriptions
Name
NC
VSS
SDA
VCLK
VCC
SCL
WP
Description
No connection
Ground
Serial address/data I/O
Serial clock (transmit only mode)
Power supply
Serial clock (bi-directional mode)
Write protect (active low)
PDIP Package
SOP Package
Note.
See pin description (continued) for more detailed
Ordering Information
AM24LC 21 X X X
Operating Voltage
LC : 2.5V~5.5V,CMOS
Type
1K Dual Mode
Temp. grade
Blank : 0
o
C ~
+
70
o
C
I
o
o
:
−
40 C ~
+
85 C
Package
S : SOP-8L
N : PDIP-8L
Packing
Blank : Tube
A : Taping
This datasheet contains new product information. Anachip Corp. reserves the rights to modify the product specification without notice. No liability is assumed as a result of the use of
this product. No rights under any patent accompany the sale of the product.
Rev. 0.0 Aug 10, 2002
1/13
AM24LC21
Dual Mode, 1K-bits (128 x 8) 2-Wire Serial EEPROM
Block Diagram
SDA
SCL
I/O
control logic
HV generator
(Preliminary)
VCLK
EEPROM
Array
Page latches
XDec
WP
Memory
control logic
VCC
YDec
VSS
Sense AMP
R/W* control
Anachip Corp.
www.anachip.com.tw
2/13
Rev 0.0 Aug 10, 2002
AM24LC21
Dual Mode, 1K-bits (128 x 8) 2-Wire Serial EEPROM
Absolute Maximum Ratings
(Note)
Symbol
V
CC
V
SS
T
OP
T
STG
Parameter
Voltage with respect to ground
All inputs and outputs w.r.t.
Operating temperature
Storage temperature
Rating
7
-0.6V to Vcc+1
0 to + 70 (commercial)
-40 to +85 (industrial)
-65 to +125
Unit
V
V
°C
°C
(Preliminary)
DC Electrical Characteristics
( Vcc=2.5V to 5.5V, T
Symbol
V
IH
V
IL
V
IH
V
IL
V
HYS
V
OL1
V
OL2
I
LI
I
LO
I
CC(Write)
I
CC(Read)
I
CCS
Parameter
SCL and SDA pins:
High level input voltage
SCL and SDA pins:
Low level input voltage
VCLK pin input level:
High level input voltage
VCLK pin input levels:
Low level input voltage
Hysteresis of Schmitt
inputs
Low level output voltage
Low level output voltage
Input leakage current
Output leakage current
Operating current
Operating current
standby current
AC
=0
o
C ~ +70
o
C, T
AI
= -40
o
C ~ +85
o
C)
Conditions
−
−
V
CC
≥2.7V
(Note)
V
CC
<2.7V (Note)
trigger
(Note)
I
OL
=3mA, V
CC
=2.5V (Note)
I
OL
=6mA, V
CC
=2.5V
V
IN
= 0.1V to V
CC
V
OUT
= 0.1V to V
CC
V
CC
= 5.5V, SCL=400Khz
V
CC
= 5.5V, SCL=400Khz
V
CC
= 3V, SDA=SCL= V
CC
V
CC
= 5.5V, SDA=SCL= V
CC,
VCLK=V
SS
Min.
0.7Vcc
−
2
−
0.05Vcc
−
−
-10
-10
−
−
−
−
Max.
−
0.3Vcc
−
0.2Vcc
−
0.4
0.6
10
10
3
1
30
100
Unit
V
V
V
V
V
V
V
uA
uA
mA
mA
uA
Note :
This parameter is periodically sampled and not 100% tested
Anachip Corp.
www.anachip.com.tw
3/13
Rev 0.0 Aug 10, 2002
AM24LC21
Dual Mode, 1K-bits (128 x 8) 2-Wire Serial EEPROM
AC Electrical Characteristics
Symbol
F
CLK
T
H
T
L
T
R
T
F
T
HD(ST)
T
SU(ST)
T
HD(DI)
T
SU(DI)
T
SU(STP)
T
AA
T
BUF
T
OF
T
SP
T
WR
T
VAA
T
VH
T
VL
T
VHZ
T
VPU
−
Parameter
Clock frequency
Clock high time
Clock low time
SDA and SCL rise
time
SDA and SCL fall
time
Start condition hold
time
Start
condition
setup time
Data input hold time
Data input setup
time
Stop
condition
setup time
Output valid from
clock
Bus free time
Output fall time from
V
IH(min)
to V
IL(max)
Input filter spike
suppression (SDA
and SCL pins)
Write cycle time
Output valid from
V
CLK
VCLK high time
VCLK low time
Mode transition time
Transmit only power
up time
Endurance
Standard Mode
Min
−
4
4.7
−
−
4
4.7
0
0.25
4
−
4.7
−
−
−
−
4
4.7
−
0
1M
Max
100
−
−
1
0.3
−
−
−
−
−
3.5
−
0.25
0.05
10
2
−
−
0.5
−
−
Vcc=4.5V~5.5V
Fast mode
Min
Max
400
−
0.6
−
1.3
−
−
−
0.6
0.6
0
0.1
0.6
−
1.3
20+0.1C
B
−
−
−
0.6
1.3
−
0
1M
0.3
0.3
−
−
−
−
−
0.9
−
0.25
0.05
10
1
−
−
0.5
−
−
cycles
Unit
Khz
us
us
us
us
us
us
us
us
us
us
us
us
us
ms
Remarks
−
−
−
(Note1)
(Note1)
After this period the first
clock pulse is generated
Only relevant for
repeated start condition
(Note 2)
−
−
(Note 2)
Time the bus must be
free before a new
transmission can start
(Note 1), C
B
≤100pF
(Note 3)
Byte or page mode
−
−
−
−
−
25
0
C, V
CC
=5V, Block
mode (Note 4)
(Preliminary)
Note 1.
Not 100% tested. C
B
=total capacitance of one bus line in pF.
Note 2.
As a transmitter, the device must provide an internal minimum delay time to bridge the undefined region (minimum 300ns) of the
falling edge of SCL to avoid unitended generation of start or stop conditions
Note 3.
The combined T
SP
and V
hys
specifications are due to new schmitt trigger inputs which provide improved noise and spike
suppression. This eliminates the need for a T
l
specification for standard operation.
Note 4.
This parameter is not tested but ensured by characterization.
Anachip Corp.
www.anachip.com.tw
4/13
Rev 0.0 Aug 10, 2002
AM24LC21
Dual Mode, 1K-bits (128 x 8) 2-Wire Serial EEPROM
Functional description
1.0 Overview
The AM24LC21 operates in two modes, the
transmit-only mode and the bi-directional mode.
There is a separate two wire protocol to support
each mode, each having a separate clock input and
sharing a common data line (SDA). The device
enters the Transmit-Only Mode upon power-up. In
this mode, the device transmits data bits on the
SDA pin in response to a clock signal on the VCLK
pin. The device will remain in this mode until a valid
high to low transition is placed on the SCL input.
When a valid transition on SCL is recognized, the
device will switch into the bi-directional mode. The
only way to switch the device back to the
transmit-only mode is to remove power from the
device.
2.1 Transmit-only mode
The device will power up in the transmit-only mode.
This mode supports a unidirectional two wire
protocol for trans-mission of the contents of the
memory array. This device requires that it be
initialized prior to valid data being sent in the
transmit-only mode (see Initialization Procedure,
SCL
T
VAA
SDA
B
IT
1(LSB)
VCLK
T
VHIGH
T
VLOW
T
VAA
N
ULL
B
IT
B
IT
8(MSB)
B
IT
7
(Preliminary)
below). In this mode, data is transmitted on the
SDA pin in 8 bit bytes, each followed by a ninth, null
bit (see Figure 2-1). The clock source for the
transmit-only mode is provided on the VCLK pin,
and a data bit is output on the rising edge on this
pin. The eight bits in each byte are transmitted most
significant bit first. Each byte within the memory
array will be output in sequence. When the last byte
in the memory array is transmitted, the output will
wrap around to the first location and continue. The
bi-directional mode clock (SCL) pin must be held
high for the device to remain in the transmit-only
mode.
2.2 Initialization procedure
After VCC has stabilized, the device will be in the
transmit-only mode. Nine clock cycles on the VCLK
pin must be given to the device for it to perform
internal synchronization. During this period, the
SDA pin will be in a high impedance state. On the
rising edge of the tenth clock cycle, the device will
output the first valid data bit which will be the most
significant bit of a byte. The device will power up at
According to the British Daily Mail, Japan's National Institute of Advanced Industrial Science and Technology (AIST) has recently developed a new "female" robot that can talk, walk and has rich expres...
What is the difference between byte alignment on ARM platform and i386 general platform? How does the compiler align the stack variables in general functions? I know that byte alignment is not only re...
For this thing I made, it is very important that the PCB area must be small, the smaller the better. After searching for a long time, I chose TI's power chip TPS63000 series products to generate 3.3V,...
Assume that data is read from 8-bit AD (if it is a higher-bit AD, the data type can be defined as int), the subroutine is get_ad();
1. Limited secondary filtering
/* A value can be adjust...[Details]
introduction
Since the beginning of the 21st century, the world of information has changed rapidly. Maybe a high-tech product will be released today and a better similar product will be releas...[Details]
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
Today, with the increasing integration of functions, mobile phones can also be used as portable media players (PMP), digital cameras, handheld computers (PDAs), and even global positioning systems ...[Details]
introduction
Throughout the history of automotive lighting, power has always played an important role. Initially, cars only needed headlights to see the road in the dark. Later, other light so...[Details]
Floating-point digital signal processing has become a constant requirement for precision technology, often in applications requiring high accuracy in areas such as aviation, industrial machinery, a...[Details]
introduction
In the discharge process of tokamak plasma physics, the study of rupture and sawtooth is of great significance. Rupture and sawtooth exist in most tokamaks. Rupture is a notew...[Details]
1 Introduction
With the acceleration of the pace of urban modernization, society has higher requirements for urban road lighting and urban lighting projects. The state has clearly required tha...[Details]
1 Introduction
Solar street lights are mainly composed of four parts: solar photovoltaic cell components, batteries, charge and discharge controllers, and lighting fixtures. The bo...[Details]
I. Introduction
In the field of power conversion, isolated converters (forward, flyback, and double-ended) with low output DC voltage all use MOSFET as the rectifier device. Since these devi...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
Power management solutions for today's portable application processors are becoming increasingly integrated. Total power consumption, standby and sleep current consumption affect battery size, bill...[Details]
We know that microcontroller development tools generally include real-time online emulators and programmers. Among them, online emulators are very good tools, but they are also more expensive...[Details]
A multi-point temperature control heating control system was designed using the SST89E564RC single-chip microcomputer and a new temperature measuring device. The heating system can be controlled in...[Details]
my country is a big country in agriculture, grain production and consumption. Grains are a necessary condition for our nation to survive and develop. The flour processing industry will exist forever w...[Details]
Robotics Development
京公网安备 11010802033920号
EEWORLD
