346-93-156-41-012 datasheet, PDF

Datasheet> All Categories > The connector> socket> 346-93-156-41-012

346-93-156-41-012: DescriptionIC Socket, SIP56, 56 Contact(s); CategoryThe connector socket; File Size150KB，1 Pages; ManufacturerMill-Max; Websitehttps://www.mill-max.com

Download Datasheet Parametric View All

346-93-156-41-012 Overview

IC Socket, SIP56, 56 Contact(s)

346-93-156-41-012 Parametric

Parameter Name	Attribute value
Is it Rohs certified?	incompatible
Maker	Mill-Max
Reach Compliance Code	compliant
ECCN code	EAR99
Is Samacsys	N
Other features	SIP SOCKET
Contact to complete cooperation	GOLD (30) OVER NICKEL
Contact completed and terminated	TIN LEAD (200) OVER NICKEL
Contact material	NOT SPECIFIED
Device slot type	IC SOCKET
Type of equipment used	SIP56
Shell material	GLASS FILLED POLYETHYLENE POLYESTER
JESD-609 code	e0
Manufacturer's serial number	346
Number of contacts	56
Base Number Matches	1

Preview

Download Datasheet

View All

SINGLE-IN-LINE SOCKETS

Solderless Press-Fit

Single Row

•

Unique compliant tail pins conform to

the plated thru-hole without stressing

the inner layers of a multilayer board.

•

Recommended plated thru-hole for

304 series: .036”-.041” use a 1.1mm

drill prior to plating. Using M-M# 0477

& 0478 pins.

•

For 346 series: .040”±.003” finished

plated thru-hole. using M-M# 4612

& 4613 pins. Patent No. 4,799,904.

Hi-Rel, 4-finger BeCu #30 clip rated

at 3 amps. See page 208 for details.

Series 304, 346

•

Fig. 1

Ordering Information

Series 304...770

SOLDERLESS PRESS-FIT

(For .062” Thick Boards)

Fig. 1

Series 304...780

304-13-1_ _-41-770

Specify # of pins

(For .125” Thick Boards)

01-64

SOLDERLESS PRESS-FIT

304-13-1_ _-41-780

Fig. 2

Specify # of pins

01-64

Series 304...770 and 304...780 are available in plating code 13 only.

Series 346...012

COMPLIANT SOLDERLESS PRESS-FIT

(For .060-.100” Thick Boards)

Fig. 3

Series 346...013

Fig. 3

346-XX-1_ _-41-012

Specify # of pins

01-64

COMPLIANT SOLDERLESS PRESS-FIT

(For .090-.130” Thick Boards)

Fig. 4

346-XX-1_ _-41-013

Specify # of pins

01-64

XX= Plating Code

See Below

SPECIFY PLATING CODE XX=

10µ” Au

30µ” Au

200µ” Sn/Pb

Sleeve (Pin)

200µ” Sn/Pb 200µ” Sn/Pb

Fig. 4

Contact (Clip)

Mill-Max-Mfg.Corp., P.O. Box 300, 190 Pine Hollow Road, Oyster Bay, NY 11771-0300.Tel: 516-922-6000 Fax: 516-922-9253

Recommended Resources

What is the difference between an adapter and a charger?

Y-△ voltage reduction control circuit controlled by DC relay

Simple phase sequence detection circuit diagram

Lithium battery fast charger circuit diagram

Galin HC-12 hot and cold water dispenser circuit diagram

Simplified schematic diagram of delta conversion UPS

About 2812 hardware: I recently used 2812 and found two very puzzling problems. 1. I used 18K and 22K resistor divider network to convert 5V TTL signal into 3.3V TTL signal, but it didn't work at all. The low level turned...; xiaohu Microcontroller MCU

Please advise: How can I become familiar with embedded design as quickly as possible?: Hello everyone, I am an absolute novice and rookie. I used to work in microwave design in Shanghai for more than two years, and then I returned to Dalian due to some family reasons. Dalian is more eng...; 09930051321 Embedded System

Experience in using PWM of 28069 and 28377D of C28x series: The basic principle of pulse width modulation (PWM): The control method is to control the on and off of the switching devices in the inverter circuit so that a series of pulses with equal amplitude ar...; Aguilera Microcontroller MCU

Microwave Circuit Rules of Thumb: This article is translated from Microwaves101 | Microwave Rules of Thumb, which summarizes some rules of thumb in microwave circuits. The so-called rules of thumb are some rules summarized over a long...; btty038 RF/Wirelessly

DIY Magic Lantern: Here we introduce a simple and easy-to-make fun production - magic lamp. The circuit is shown in Figure 1. As long as you hold the magic wand with a permanent magnet in your hand and shake it from bot...; yuandayuan6999 DIY/Open Source Hardware

CCS source file compilation order problem: When ccs compiles source files, which one should be compiled first and which one should be compiled later?...; powered DSP and ARM Processors

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components