177-710-5-9CS4J1-24LDN datasheet, PDF

Datasheet> All Categories > The connector> The connector> 177-710-5-9CS4J1-24LDN

177-710-5-9CS4J1-24LDN: DescriptionInterconnection Device; CategoryThe connector The connector; File Size436KB，4 Pages; ManufacturerGlenair; Websitehttp://www.glenair.com/; Environmental Compliance

Download Datasheet Parametric View All

177-710-5-9CS4J1-24LDN Overview

Interconnection Device

177-710-5-9CS4J1-24LDN Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Reach Compliance Code	compliant
Connector type	INTERCONNECTION DEVICE
Base Number Matches	1

Preview

Download Datasheet

View All

MWDM Micro-D Shielded Cable Assemblies

Single-Ended or Double-Ended–These

easy-to-order cable

assemblies eliminate the need for expensive assembly

labor. 100% tested and ready for use.

Now With Twisted Pairs–No

need to create a procurement

speciﬁcation for Micro-D cables with twisted pairs. Glenair

177-740 cables are furnished with a full complement of

white/blue twisted pair wires.

Integral Shield Termination–The

connector shell has a

platform to accept Band-It shield termination bands. The

cable shield braid is attached directly to the connector.

Save Labor, Reduce Weight and Improve EMI Shielding with

Glenair’s Micro-D Shielded Cable Assemblies

Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s fully

shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-piece connector

shell and secured with a stainless steel

BAND-IT

® clamp. These pre-wired, 100% tested assemblies meet the

requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low shell-to-shell resistance.

Available with a variety of wire types and shields, Micro-D shielded assemblies can be ordered in any length, either

single-ended or “back-to-back”.

Ground Spring and EMI Shielding Effectiveness

– A gold-plated

stainless steel ground spring on the pin connector mating face offers

substantial improvement in EMI protection. The graphs compare

identical connectors tested with and without ground springs.

EMI Performance with Ground Spring

SHIELDING EFFECTIVENESS (DB)

100

1.00E+03

100

1.00E+03

EMI Performance without Ground Spring

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

FREQUENCY (Hz)

CAGE Code 06324/0CA77

Printed in U.S.A.

GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912

www.glenair.com

B-8

E-Mail: sales@glenair.com

Recommended Resources

Commonly used non-sinusoidal oscillator circuits, waveforms and frequency calculation formulas-square wave oscillator-self-excited multivibrator

Industrial four-way programmable controller power circuit

Typical application circuit diagram of MAX764,765,766a

Thermocouple alarm signal output circuit

M9082 (TV) infrared remote control transmitter microprocessor

MAXTl3 switch mode application circuit

Another question!: How to achieve 2.3Mbps data rate in uplink dedicated channel in WCDMA?...; manly RF/Wirelessly

consult: How to reduce the 12v switching power supply to 5v and 9v? It would be best to provide a circuit diagram. Thank you...; ap0505525 MCU

PT2262 decoding sharing: After reading the manual of pt2262, I understood the protocol. I used TCNT0 to measure the pulse width and LCD1602 to display it. After obtaining the code, I used the transmitting circuit to transmit ...; eeleader MCU

Component packaging: Is there any difference between the component packaging in the two standard systems of EIA and EIAJ ? Please give me some advice. . . ....; lyklyz PCB Design

Steps and precautions for converting DXP and Protel 99 SE via cover oil to GERBER: [align=left] [/align][align=left]Please note that before outputting GERBER, you must first consider whether the via (VIA) is open or covered with oil. The following introduces how each software handle...; szjlczhang PCB Design

Framebuffer switching issue on Android platform.: Android platform, need to switch between LCD output and DVI output, there are three fb in /dev/graphics, namely fb0, fb1, fb2. When I use LCD as the default output, I found that fb0 is used to process...; nibuhao123 Embedded System

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components