0.5A Positive Low Dropout Fixed-Mode Regulator With EN Function
Features
•
•
•
•
•
•
•
General Description
AP1119 is a low dropout positive adjustable or
fixed-mode regulator with minimum of 0.5A output
current capability. The product is specifically
designed to provide well-regulated supply for low
voltage IC applications such as high-speed bus
termination and low current 3.3V logic supply.
AP1119 is also well suited for other applications
such as VGA cards. AP1119 is guaranteed to have
<1.3V dropout at full load current making it ideal to
provide well regulated fixed outputs of 1.5 to 12V
with up to 18V input supply. The AP1119 offers a
TTL – Logic compatible enable pin.
1.3V maximum dropout at full load current
Fast transient response
Output current limiting
Built-in thermal shutdown
Packages: SOT89-5L
Good noise rejection
5-Terminal device with fixed 1.5V, 1.8V, 2.5V,
3.3V, 5.0V, 9.0V, 12V output.
Applications
•
•
•
PC peripheral
Communication
CDROM..
Ordering Information
AP 1119 X XX X X
Low Dropout Regulator
Package
Y : SOT89-5L
Vout
15 : 1.5V
18 : 1.8V
25 : 2.5V
33 : 3.3V
50 : 5.0V
90 : 9.0V
12 : 12V
Lead Free
Blank : Normal
L : Lead Free Package
Packing
Blank : Tube
A : Taping
Typical Circuit
5V
C1
100uF
NC
Tab is Vout
ON OFF
EN
4
3
2
Vin
3.3V/0.5A
Vout
GND
5
1
C2
100uF
( 5V/3.3V fixed output )
This datasheet contains new product information. Anachip Corp. reserves the rights to modify the product specification without notice. No liability is assumed as a result of the use of
this product. No rights under any patent accompany the sale of the product.
Rev. 1.0 Aug 20, 2004
1/5
Not Recommended for New Design
AP1119
0.5A Positive Low Dropout Fixed-Mode Regulator With EN
Function
Connection Diagram
5 PIN SOT89
NC
Tab is Vout
EN
4
3
2
Vin
Vout
GND
5
1
Pin Descriptions
NAME
GND
Vout
Ground
The output of the regulator. A minimum of 10uF capacitor must be connected from this pin
to ground to insure stability.
The input pin of regulator. Typically a large storage capacitor is connected from this pin to
ground to insure that the input voltage does not sag below the minimum dropout voltage
during the load transient response. This pin must always be 1.3V higher than Vout in order
for the device to regulate properly.
The input pin of regulator. TTL/CMOS compatible input Logic high = disable output, Logic
Low or open =Enable output. (internal Pull-down resistor ~ l00K).
FUNCTION
Vin
EN
Absolute Maximum Ratings
Characteristics
DC Supply Voltage
Power Dissipation
Storage Temperature
Operating Junction Temperature Range
Symbol
Vin
P
D
T
ST
T
OP.
Values
-0.3 to 18
Internally Limited
-65 to +150
0 to +150
oC
oC
Unit
V
Anachip Corp.
www.anachip.com.tw
2/5
Rev. 1.0 Aug 20, 2004
Not Recommended for New Design
AP1119
0.5A Positive Low Dropout Fixed-Mode Regulator With EN Function
Philips introduces new high-speed register for DDR2 memory modulesDesigned to optimize storage performance, including the industry's fastest registers2009-01-19 As memory module solutions evolve fr...
As the title says: How to close the window instead of hiding it when clicking the OK button in the upper right corner of the window? It is equivalent to executing the this.Dispose() method in the curr...
Introduction: TMS320C64x+ Network Course 6 - EDMA3.0, related information includes: the basic architecture of EDMA3.0, two controllers (transmission controller and channel controller), the parameters ...
The world's ten greatest formulas. How many great minds have spent their entire lives to finally write an equal sign. Salute! The British scientific journal "Physical World" once asked readers to vote...
Altera Cyclone V Soc development board appreciation, a Terasic Sockit, a Cytech Helio Soc. Anyone interested in research can share their experience....
[i=s]This post was last edited by zzw_rst on 2022-1-17 00:42[/i]For example, there are 11 information bits and 4 check bits. When building the check rule, I don't understand how many information bits ...
This program is written to simulate the serial port hardware mechanism. When used, a timed interrupt can be set with a time interval of 1/4 baud rate. The receiving function is called once for ea...[Details]
DSP (digital signal processor) is used more and more frequently in today's engineering applications. There are three main reasons for this: first, it has powerful computing power and is capable of ...[Details]
1. What is temperature?
Heat is a type of molecular motion. The hotter an object is, the faster its molecules move. Absolute zero is defined as the temperature at which all molecular motion ...[Details]
1 Introduction
Building Automation System (BAS) is a distributed monitoring system (DCS) designed according to distributed information and control theory. It is the result of the mutual de...[Details]
1 Introduction
With the development of control, computer, communication, network technology, etc., a new control technology, namely fieldbus, has emerged in the field of industrial control...[Details]
Nippon Electric Works and Volvo Technology Japan have developed a wireless power supply system for electric vehicles (EVs). Using this system, the two companies have successfully conducted an exper...[Details]
Capacitors
are basic components in various electronic devices and are widely used for bypassing, coupling,
filtering
, tuning, etc. in electronic circuits. However, to use capacitors,...[Details]
Introduction
In industrial control, speed measurement is often required. Generally, a contact tachometer is used. This tachometer must be placed against the center of the shaft to measure. It...[Details]
Traditional
virtual instruments
consist of a data acquisition
board
based on PCI bus and
corresponding software. However, with
the rapid development of
computer
network techno...[Details]
1 Introduction
Ultrasound refers to elastic vibration with a frequency higher than the audible frequency limit (i.e., in the frequency band above 20 kHz). The propagation process of this vib...[Details]
At present, a large number of cooling tower fans, speed fans and special fans are in use in petroleum, chemical, pharmaceutical, metallurgical and other enterprises. Some fans have no monitoring in...[Details]
0 Introduction
Wireless Sensor Network (WSN) monitors the target by deploying a large number of sensor nodes in the target area. WSN realizes the positioning and tracking of the target, determi...[Details]
The production process of lithium batteries does not mention the previous processes such as material preparation, winding, liquid injection, and packaging, but only talks about the final formation ...[Details]
The power consumption of a switching power supply includes fixed losses caused by parasitic resistances such as semiconductor switches, magnetic components, and wiring, as well as switching losses ...[Details]
Today's automotive application developers face numerous design challenges as modern cars add more electronic functionality, while the need for lower power consumption and smaller printed circuit bo...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
