EEWORLDEEWORLDEEWORLD

Part Number

Search

54121-115021050LF

Description
Board Connector, 2 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size101KB,1 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

54121-115021050LF Overview

Board Connector, 2 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle

54121-115021050LF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerAmphenol
Reach Compliance Codecompliant
Is SamacsysN
body width0.094 inch
subject depth0.413 inch
body length0.2 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact completed and terminatedMatte Tin (Sn) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialTHERMOPLASTIC
JESD-609 codee3
Manufacturer's serial number54121
Plug contact pitch0.1 inch
Installation option 1LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
Plating thickness30u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.095 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts2
Base Number Matches1
PDM: Rev:G
STATUS:
Released
Printed: Mar 10, 2011
.
Speaker? Piggy bank? ?
Is the little thing in the picture above a speaker or a piggy bank? If it is really that simple, wouldn't it be a waste of my typing so many words on the holiday? Without keeping you in suspense, I wi...
小丸子 DIY/Open Source Hardware
gw1n FPGA reads ADS8598H actual DC measurement
The experimental board has not been fully soldered yet. Use flying wires to connect to the FPGA to measure its 3.3V power supply. The multimeter measures 3.293V.At present, the FPGA side directly chec...
littleshrimp Domestic Chip Exchange
Shouldn't the charging curve of a capacitor be inversely proportional to its discharging curve?
Shouldn't the charging curve of a capacitor be inversely proportional to its discharging curve?...
QWE4562009 Integrated technical exchanges
Various topics for e-sports competitions
[i=s]This post was last edited by paulhyde on 2014-9-15 09:10[/i] These are reports on various topics, very useful, make good use of them...
zhixiongxue Electronics Design Contest
Isolation problem of ground wire of DC linear regulated power supply?
I plan to make a 220V AC to ±12V, ±5V, 3.3V DC linear voltage regulator power supply. Do the ground wires of different voltages need to be isolated? I use a series of voltage regulator chips such as L...
燕园技术宅 Power technology
IP core issues in ISE
Recently I downloaded a code about implementing UDP protocol with FPGA from CSDN. The board of the code is xc6slx45-2csg324, and my board model is xc3s500e-4pq208. When translating, an error message a...
Domipy FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1149  2258  1958  1462  542  24  46  40  30  11 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号