The LP2950 and LP2951 are micropower voltage regulators ideally suited for use in battery-powered systems. These devices
feature very low quiescent current (typ.75µA), and very low dropout voltage (typ.45mV at light loads and 380mV at 100mA)
thus prolonging battery life. The quiescent current increases only slightly in dropout. The LP2950/LP2951 has positive
transient protection up to 60V and can survive unregulated input transient up to 20V below ground.
The LP2950 and LP2951 were designed to include a tight initial tolerance (typ. 0.5%), excellent load and line regulation (typ.
0.05%), and a very low output voltage temperature coefficient, making these devices useful as a low-power voltage reference.
The LP2950 is offered in the 3-pin TO-92 package. LP2951 is available in 8-pin plastic SOIC and DIP packages and offers
three major additional system features. An error flag output warns of a low output voltage, often due to failing batteries on
input. The LP2951 also features the logic-compatible shutdown input which enables the regulator to be switched on and off.
The LP2951 device may be pin-strapped for a 5V, 3.3V, or 3V output, or programmed from 1.24V to 29V with an external
pair of resistors.
ORDERING INFORMATION
PACKAGE TYPE
TO-92
8 LEAD PDIP 8 LEAD SOIC
LP2950ACN-X LP2951ACP-X LP2951ACS-X
LP2950CN-X
LP2951CP-X
LP2951CS-X
X = 3.3V, or 3V
OPERATING
TEMP. RANGE
IND.
IND
PIN CONNECTION
8L SOIC/ 8L PDIP
OUTPUT 1
SENSE 2
SHUTDOWN 3
GROUND 4
8 INPUT
7 FEEDBACK
6 V
TAP
5 ERROR
Top View
TO-92
OUTPUT
INPUT
GND
Bottom View
Advanced Monolithic Systems, Inc.
www.advanced-monolithic.com
Phone (925) 443-0722
Fax (925) 443-0723
LP2950/LP2951
ABSOLUTE MAXIMUM RATINGS
(Note 1)
Input Supply Voltage
SHUTDOWN Input Voltage,
Error Comparator Output
Voltage,(Note 9)
FEEDBACK Input Voltage
(Note 9) (Note 10)
Power Dissipation
Junction Temperature
Storage Temperature
Soldering Temperature (25 sec)
-0.3 to +30V
OPERATING RATINGS
(Note 1)
Max. Input Supply Voltage
Junction Temperature Range
(T
J
) (Note 8)
LP2950AC-XX, LP2950C-XX
LP2951AC-XX, LP2951C-XX
30V
-1.5 to +30V
Internally Limited
+150°C
-65°C to +150°C
260°C
-40°C to +125°C
ELECTRICAL CHARACTERISTICS
at Vs=Vout+1V, Ta=25°C, unless otherwise noted
.
Parameter
3 V Versions
(Note 16)
Output Voltage
TJ = 25°C
(Note 3)
-25°C
≤T
J
≤85°C
Full Operating Temperature
Range
100
µA ≤I
L
≤100
mA
TJ
≤T
JMAX
TJ = 25°C
(Note 3)
-25°C
≤T
J
≤85°C
Full Operating Temperature
Range
100
µA ≤I
L
≤100
mA
TJ
≤T
JMAX
TJ = 25°C
(Note 3)
-25°C
≤T
J
≤85°C
Full Operating Temperature
Range
100
µA ≤I
L
≤100
mA
TJ
≤T
JMAX
2.985
2.970
2.964
2.958
3.0
3.0
3.0
3.0
3.015
3.030
3.036
3.042
2.970
2.955
2.940
2.928
3.0
3.0
3.0
3.0
3.030
3.045
3.060
3.072
V
V
V
V
Conditions
(Note 2)
Min.
LP2950AC
LP2951AC
Typ.
Max.
Min.
LP2950C
LP2951C
Typ.
Max.
Units
Output Voltage
3.3 V Versions
(Note 16)
Output Voltage
3.284
3.267
3.260
3.254
3.3
3.3
3.3
3.3
3.317
3.333
3.340
3.346
3.267
3.251
3.234
3.221
3.3
3.3
3.3
3.3
3.333
3.350
3.366
3.379
V
V
V
V
Output Voltage
5 V Versions
(Note 16)
Output Voltage
4.975
4.95
4.94
4.925
5.0
5.0
5.0
5.0
5.025
5.050
5.06
5.075
4.95
4.925
4.90
4.88
5.0
5.0
5.0
5.0
5.05
5.075
5.10
5.12
V
V
V
V
Output Voltage
All Voltage Options
Output Voltage
Temperature Coefficient
Line Regulation (Note 14)
Load Regulation (Note 14)
Dropout Voltage
(Note 5)
Ground Current
(Note 12) (Note 4)
6V
≤V
in
≤30V
(Note 15)
100
µA ≤I
L
≤
100 mA
IL = 100µ A
IL = 100 mA
IL = 100
µA
IL = 100 mA
Vout = 0
(Note 13)
20
0.03
0.04
50
380
75
8
160
0.05
0.1
0.1
80
450
120
12
200
0.2
50
0.04
0.1
50
380
75
8
160
0.05
0.2
0.2
80
450
120
12
200
0.2
ppm/°C
%
%
mV
mV
µA
mA
mA
%/W
Current Limit
Thermal Regulation
Advanced Monolithic Systems, Inc.
www.advanced-monolithic.com
Phone (925) 443-0722
Fax (925) 443-0723
LP2950/LP2951
ELECTRICAL CHARACTERISTICS
(Note 2) (Continued)
PARAMETER
Output Noise,
10Hz to 100KHz
CONDITIONS
(Note 2)
CL = 1µF
CL = 200
µF
CL = 13.3
µF
(Bypass = 0.01
µF
pins 7 to
1(LP2951))
Min.
LP2950AC
LP2951AC
Typ.
430
160
100
LP2951AC
1.22
1.235
1.25
1.27
40
20
60
1.21
1.185
Max.
Min.
LP2950C
LP2951C
Typ.
430
160
100
LP2951C
1.235
1.26
1.285
40
60
50
Max.
Units
µV
rms
µV
rms
µV
rms
8-Pin Versions only
Reference Voltage
Reference Voltage
Feedback Pin Bias Current
Reference Voltage Temperature
Coefficient
Feedback Pin Bias Current
Temperature Coefficient
Error Comparator
Output Leakage Current
Output Low Voltage
Upper Threshold Voltage
Lower Threshold Voltage
Hysteresis
Shutdown Input
Input logic Voltage
Shutdown Pin Input Current
(Note 3)
Regulator Output Current in
Shutdown (Note 3)
V
OH
V
V
nA
ppm/°C
Over Temperature (Note 7)
1.19
( Note 12 )
0.1
0.1
nA/°C
= 30V
0.01
150
40
60
75
15
1
250
40
95
0.01
150
60
75
15
1
250
µA
mV
mV
Vin = 4.5V
IOL = 400µA
(Note 6)
(Note 6)
(Note 6)
Low (Regulator ON)
High (Regulator OFF)
Vs = 2.4V
Vs = 30V
(Note 11)
95
mV
mV
1.3
2
30
450
3
0.7
2
50
600
10
1.3
30
450
3
0.7
50
600
10
V
V
µA
µA
µA
Note 1:
Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which operation of the
device is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions, see the
Electrical Characteristics tables.
Note 2:
Unless otherwise specified all limits guaranteed for V
IN
= ( V
ONOM
+1)V, I
L
= 100
µA
and C
L
= 1
µF
for 5V versions and 2.2µF for 3V and 3.3V
versions. Limits appearing in
boldface
type apply over the entire junction temperature range for operation. Limits appearing in normal type apply for T
A
= T
J
=
25°C Additional conditions for the 8-pin versions are FEEDBACK tied to V
TAP
, OUTPUT tied to SENSE and V
SHUTDOWN
≤
0.8V.
Note 3:
Guaranteed and 100% production tested.
Note 4:
Guaranteed but not 100% production tested. These limits are not used to calculate outgoing AQL levels.
Note 5:
Dropout voltage is defined as the input to output differential at which the output voltage drops 100 mV below its nominal value measured at 1V
differential. At very low values of programmed output voltage, the minimum input supply voltage of 2V ( 2.3V over temperature) must be taken into account.
Note 6:
Comparator thresholds are expressed in terms of a voltage differential at the feedback terminal below the nominal reference voltage measured at
V
IN
= ( V
ONOM
+1)V. To express these thresholds in terms of output voltage change, multiply by the error amplifier gain = Vout/Vref = (R1 + R2)/R2. For
example, at a programmed output voltage of 5V, the error output is guaranteed to go low when the output drops by 95 mV x 5V/1.235 = 384 mV. Thresholds
remain constant as a percent of V
out
as V
out
is varied, with the dropout warning occurring at typically 5% below nominal, 7.5% guaranteed.
Note 7:
V
ref
≤V
out
≤
(V
in
- 1V), 2.3
≤V
in
≤30V,
100µA≤I
L
≤
100 mA, T
J
≤
T
JMAX
.
Note 8:
The junction-to-ambient thermal resistance are as follows:180°C/W and 160°C/W for the TO-92 (N) package with 0.40 inch and 0.25 inch leads to the
printed circuit board (PCB) respectively, 105°C/W for the molded plastic DIP (P) and 160°C/W for the molded plastic SO-8 (S). The above thermal resistances
for the N, S and P packages apply when the package is soldered directly to the PCB.
Note 9:
May exceed input supply voltage.
Note 10:
When used in dual-supply systems where the output terminal sees loads returned to a negative supply, the output voltage should be diode-clamped to
ground.
Note 11:
V
shutdown
≥
2V, V
in
≤
30V, V
out
=0, Feedback pin tied to 5V
TAP
.
Note 12:
Output or reference voltage temperature coefficients defined as the worst case voltage change divided by the total temperature range.
Advanced Monolithic Systems, Inc.
www.advanced-monolithic.com
Phone (925) 443-0722
Fax (925) 443-0723
LP2950/LP2951
Note 13:
Thermal regulation is defined as the change in output voltage at a time T after a change in power dissipation is applied, excluding load or line
regulation effects. Specifications are for a 50mA load pulse at V
IN
=30V (1.25W pulse) for T =10 ms.
Note 14:
Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output voltage due to heating effects
are covered under the specification for thermal regulation.
Note 15:
Line regulation for the LP2951 is tested at 150°C for I
L
= 1 mA. For I
L
= 100
µA
and T
J
= 125°C, line regulation is guaranteed by design to 0.2%. See
typical performance characteristics for line regulation versus temperature and load current.
Note 16:
All LP2950 devices have the nominal output voltage coded as the last two digits of the part number. In the LP2951 products, the 3.0V and 3.3V
versions are designated by the last two digits, but the 5V version is denoted with no code of the part number.
I made an integrated offline robot arm controller, which mainly controls a 3-axis robot arm, the Dobot structure. The program is still under development......
I just bought a sim300 module yesterday. I can send Chinese and English text messages, but I can't make calls. When I use my mobile phone to dial the number on the sim300, it prompts that it cannot be...
Many netizens who are new to 51 MCUs have this question: What is AT89S51? Books and online tutorials all mention 8051, 89C51, etc.! Have you ever heard of 89S51? ! Here, beginners need to clarify a ...
The actual measurement function of the sampleis used to detect the resistance of Rx (the resistance will change with temperature).The output voltage will change with the resistance of Rx.This circuit ...
1. Several nouns
ABI:
The specifications that an executable file must follow in order to run in a specific execution environment;
Separately generated relocatabl...[Details]
The problem of dynamic sealing of equipment always exists with the operation of the equipment. Today, we have specially sorted out the various commonly used sealing forms, usage scope and character...[Details]
EtherCAT (Ethernet for Control Automation Technology) is a real-time industrial fieldbus communication protocol based on an Ethernet-based development framework. EtherCAT is one of the fastest indu...[Details]
To enable real-time monitoring of home security and automatically dial a number for voice prompts or send text messages when an alarm occurs, a GPRS-based embedded telephone alarm system was design...[Details]
Electric motors and internal combustion engines of the same power have similar torque levels. High power requires high torque, and torque determines a vehicle's acceleration speed, commonly known a...[Details]
Whether it is an electric car or an ordinary fuel car, for the vast majority of car buyers, the final cost of use is what they care about most. For fuel cars, how to save fuel is what drivers care ...[Details]
Limited vocabulary recognition
According to the number of characters, words or short sentences in the vocabulary, it can be roughly divided into: less than 100 is small vocabulary; 100-1000 is...[Details]
On August 22, Lantu Motors officially launched its Lanhai Intelligent Hybrid technology via an online livestream. This intelligent hybrid technology, which integrates a full-range 800V high-voltage...[Details]
Core point: The automotive industry chain and the humanoid robot industry have collaborative advantages in hardware, software, and scenarios. Upstream and downstream companies in the automotive ind...[Details]
Recently, AstroBo Robot, a subsidiary of Chenxing Automation, launched a new mobile collaborative palletizing product. Leveraging an omnidirectional mobile chassis, an intelligent scheduling system...[Details]
Pure electric vehicles, structurally speaking, have components such as a power battery. In addition to the power battery, a small battery also powers some low-voltage electrical components and even...[Details]
With the advent of the electric car era, the number of pure electric vehicles has increased significantly, but many car owners do not know how to properly maintain pure electric vehicles. In additi...[Details]
Keysight Technologies is combining its electromagnetic simulator with Synopsys' AI-driven RF design migration flow to create an integrated design flow for migrating from TSMC's N6RF+ process techno...[Details]
Plessey Semiconductors has been acquired by Haylo Labs, which was established in March last year with a $100 million, five-year loan from Chinese technology company Goertek.
Haylo Labs w...[Details]
Magna's integrated in-cabin perception system fuses vision and millimeter-wave radar data to detect the presence of passengers, identify stranded children, monitor driver fatigue and vital signs, a...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
