EEWORLDEEWORLDEEWORLD

Part Number

Search

2-147097-2

Description
HEADER CONNECTOR,PCB MNT,PLUG,44 CONTACTS,SKT,0.1 PITCH,PC TAIL TERMINAL,BLACK
CategoryThe connector    The connector   
File Size502KB,13 Pages
ManufacturerTE Connectivity
Websitehttp://www.te.com
Download Datasheet Parametric View All

2-147097-2 Overview

HEADER CONNECTOR,PCB MNT,PLUG,44 CONTACTS,SKT,0.1 PITCH,PC TAIL TERMINAL,BLACK

2-147097-2 Parametric

Parameter NameAttribute value
MakerTE Connectivity
Reach Compliance Codeunknown
Is SamacsysN
Other featuresWITH STANDOFF, BOTTOM ENTRY
subject depth0.265 inch
Body/casing typePLUG
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact completed and terminatedTIN/LEAD OVER NICKEL
Contact point genderFEMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact resistance12 mΩ
Contact styleSQ PIN-SKT
Dielectric withstand voltage750VAC V
Durability100 Cycles
maximum insertion force2.502 N
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialTHERMOPLASTIC
Manufacturer's serial number147097
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation methodSTRAIGHT BOTTOM MOUNT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature105 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thickness15u inch
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.105 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts44
Evacuation force-minimum value.417 N
Base Number Matches1
AMPMODU*
Mod II and Mod IV Printed
Circuit Board Connectors
Application Specification
114-25018
19 MAY 08
Rev E
NOTE
i
All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters. Unless
otherwise specified, dimensions have a tolerance of +0.13 and angles have a tolerance of +2 . Figures and
illustrations are for identification only and are not drawn to scale.
_
1. INTRODUCTION
This specification covers the requirements for application of AMPMODU Mod II and Mod IV Printed Circuit
(PC) Board Connectors for through hole and Surface Mount Technology (SMT). The connectors are available
with double beam receptacle contacts designed to accept 0.64 mm square posts. There are connectors in 2
through 80 positions for top and bottom entry applications as well as pass through applications with 2.54 mm
contact centerline spacing. All side entry connectors are available in 4 through 130 positions for double rows
and 2 through 65 positions for single row. The double beam contact connectors are available with single and
double rows of contacts. There are various solder lead configurations to meet a variety of system
requirements.
There are surface mount connectors available with and without hold–downs. The hold–downs help position the
connector on the pc board and hold it in place during soldering. Through hole connectors are available with and
without retentive contact leads. The retentive contact leads help stabilize and hold the connector in place
during soldering. Connectors without hold–down or retentive contact lead stabilizing features are available to
accommodate alternate system requirements.
When corresponding with Tyco Electronics Personnel, use the terminology provided on this specification to
help facilitate your inquiry for information. Basic terms and features of components are provided in Figure 1.
Double Beam Contact
Connectors (Typ)
Double Row
Connector
Single Row
Dual Entry
Connector
Mating
Face
Double Row
Connector
Dual
Entry
Right-Angle
Horizontal
Top Entry
Contact
Cavity
Connector
Dual Entry
Right-Angle Surface
Mount (Horizontal)
Single Row
Connector
Figure 1
E
2008 Tyco Electronics Corporation, Harrisburg, PA
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at
www.tycoelectronics.com
1
of 13
LOC B
All International Rights Reserved
TE logo and Tyco Electronics are trademarks.
*Trademark. Other products, logos, and company names used are the property of their respective owners.
Absolutely good information---Preliminary exploration of embedded menu design based on LCD12864 (based on AVR microcontroller)
[b][size=5]A Preliminary Study on Embedded Menu Design Based on LCD12864[/size][/b][size=4] [/size] [size=4] [/size] [size=4]This article introduces in great detail how to develop an embedded menu on ...
tiankai001 Download Centre
A novice wants to learn DSP, but doesn't know where to start
Do you have any recommended books, videos, or which DSP should I start learning from? (Try not to be too expensive, and you don't need something too advanced at the beginning). Thank you everyone....
mengyu139 DSP and ARM Processors
Common problems in using filter masks
Question 1: Is it true that the smaller the dust, the harder it is to filter out with a mask? Answer: Generally speaking, we would think that the smaller the dust, the harder it is to filter out, but ...
shcpz Industrial Control Electronics
Help voice chip ISD25120P
I need help with the peripheral application circuit of ISD25120P. Is there any way to read the data stored in it? ? ?...
wzjhuohua Analog electronics
Ask a question about the clock generator
Hello everyone: I'm a novice in clock generators. I'm looking at ADI's AD9517. The document says that the clock generator can use an external VCO input. I want to ask if this external VCO input is inp...
418478935 FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1766  1016  1758  885  917  36  21  18  19  22 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号