Ultra-Small, Ultra-Low Power MEMS Oscillator with Spread Spectrum
Features
• Output Frequency: 1 MHz to 100 MHz LVCMOS
• Spread Spectrum Options:
- Center-Spread: ±0.25%, ±0.5%, ±1.0%,
±1.5%, ±2.0%, ±2.5%
- Down-Spread: –0.25%, –0.5%, –1.0%,
–1.5%, –2.0%, –3.0%
• Ultra-Low Power Consumption: 3 mA (Active),
1
A (Standby)
• Wide Supply Voltage Range: 1.71V ~ 3.63V V
DD
• Ultra-Small Package Sizes:
- 1.6 mm
1.2 mm
- 2.0 mm
1.6 mm
- 2.5 mm
2.0 mm
• Wide Temperature Range:
- Automotive: –40°C to +125°C
- Ext. Industrial: –40°C to +105°C
- Industrial: –40°C to +85°C
- Ext. Commercial: –20°C to +70°C
• Excellent Shock and Vibration Immunity
- Qualified to MIL-STD-883
• High Reliability
- 20x Better MTBF than Quartz Oscillators
• Lead Free and RoHS Compliant
• Automotive AEC-Q100 Option Available
General Description
The DSC63xxB family of devices is the industry’s
smallest and lowest-power spread-spectrum MEMS
oscillators. Available in three different package sizes
with operating current as low as 3 mA, the smallest
4-pin package is a mere 1.6 mm x 1.2 mm in size. The
devices support up to ±2.5% or –3% spread spectrum
that can achieve up to 15 dB electromagnetic
interference (EMI) reduction. Because of industry
standard package and pin options, customers can
solve last minute EMI problems simply by placing the
new DSC63xxB on their current board layout with no
redesign required.
The DSC63xxB family is available in 1.6 mm x 1.2 mm
and 2.0 mm x 1.6 mm, and 2.5 mm x 2.0 mm
packages. These packages are “drop-in” replacements
for standard 4-pin CMOS quartz crystal oscillators.
Package Types
DSC63
XX
B
2.5 mm x 2.0 mm VLGA
2.0 mm x 1.6 mm VFLGA
1.6 mm x 1.2 mm VFLGA
(Top View)
OE/STDBY/SSEN
1
4
VDD
Applications
•
•
•
•
Flat Panel Display/Monitor
Multi-Function Printer
Digital Signage
Consumer Electronics
GND
2
3
OUT
2019 Microchip Technology Inc.
DS20006154A-page 1
DSC63XXB
Block Diagram
DSC63
XX
B
DIGITAL
CONTROL
OE/STDBY/SSEN
PIN 1
SST
MEMS
RESONATOR
TEMP SENSOR
CONTROL &
COMPENSATION
PLL
VCO
SUPPLY
REGULATION
VDD
PIN 4
OUTPUT
DIVIDER
DRIVER
OUTPUT
PIN 3
GND
PIN 2
DS20006154A-page 2
2019 Microchip Technology Inc.
DSC63XXB
1.0
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings
Supply Voltage .......................................................................................................................................... –0.3V to +4.0V
Input Voltage (V
IN
) ..............................................................................................................................–0.3V to V
I'm using LM3S811 recently, but I obviously feel that the pins are not enough. If I make a 4*4 button with only 32 pins GPIOA, BCD, and add a 12864, there is basically nothing left... (I'm using the o...
I asked Keil, and he said that the simulator takes into account the different pulses of instruction execution for different MCUs. And I found that when I used different configurations for my MCU, the ...
After graduation, the first job I found was to work in an electronics factory as a researcher. But I didn't know anything at the time. I learned C51 in school and wrote it in assembly language. I real...
Hi guys, I have a question.There is a pulse waveform, some have 9 pulses, some have 5 pulses, and some have 2 pulses. How can I distinguish them? The 9 pulses are output as a synchronization signal. W...
This example uses the MSP430F425 microcontroller and the AT-MR500 module with an integrated MG2450 chip to realize the detection of three harmful substances, H2S, CO and CH4, and the data communicatio...
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
The Mobile Industry Processor Interface (MIPI) Alliance is an organization responsible for promoting the standardization of software and hardware in mobile devices. It has released the D-PHY specif...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
1 Introduction
Ultrasonic waves have strong directivity, slow energy consumption, and can propagate over long distances in a medium, so they are used for distance measurement. Ultrasonic detec...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
Printed circuit boards ( PCBs
)
are used in most electrical products
. If a PCB has low
insulation resistance
(IR), the performance of the circuits on the PCB will be greatly reduced...[Details]
Capacitors
are basic components in various electronic devices and are widely used for bypassing, coupling,
filtering
, tuning, etc. in electronic circuits. However, to use capacitors,...[Details]
Introduction
Nowadays, people pay more and more attention to the security alarm system, and people have higher and higher requirements for the functions and performance of the alarm. This paper prop...[Details]
introduction
At present, measuring instruments are developing towards networking, and each individual embedded instrument will become a node on the Internet. This system realizes the network...[Details]
With the rapid development of cities and the improvement of citizens' living standards, the number of various vehicles in cities is growing, and the demand for parking spaces in major commercial an...[Details]
1 Introduction
Ultrasound refers to elastic vibration with a frequency higher than the audible frequency limit (i.e., in the frequency band above 20 kHz). The propagation process of this vib...[Details]
Electric bicycles have long been a means of transportation for lower-income groups due to their affordability. The largest concentrated expense in the use of electric vehicles is the cost of replac...[Details]
Multimedia processors are often the most power-hungry devices in portable electronic devices. Common ways to reduce CPU power requirements are to reduce clock frequency or operating voltage, but th...[Details]
Power supply is often the most easily overlooked link in the circuit design process. In fact, as an excellent design, power supply design should be very important, which greatly affects the perfor...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
