EEWORLDEEWORLDEEWORLD

Part Number

Search

WCTN26114002C

Description
RES NET,THIN FILM,140K OHMS,100WV,.2% +/-TOL,-100,100PPM TC,0303 CASE
CategoryPassive components    The resistor   
File Size118KB,3 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

WCTN26114002C Overview

RES NET,THIN FILM,140K OHMS,100WV,.2% +/-TOL,-100,100PPM TC,0303 CASE

WCTN26114002C Parametric

Parameter NameAttribute value
Objectid1171449122
package instructionSMT, 0303
Reach Compliance Codeunknown
ECCN codeEAR99
structureChip
Manufacturer's serial numberCTN
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height0.254 mm
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingTray
Rated power dissipation(P)0.25 W
GuidelineMIL-STD-883
resistance140000 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesCTN
size code0303
Temperature Coefficient100 ppm/°C
Tolerance0.2%
Operating Voltage100 V
CTN
Vishay Electro-Films
Nichrome Thin Film, Center Tapped Resistors
CHIP
RESISTORS
FEATURES
Wire bondable
Product may not
be to scale
Center tap feature
Chip size: 0.030 inches square
Resistance range total: 10
Ω
to 1 MΩ
Ratio tolerances to: 0.1 %
Resistor material: Nichrome
Oxidized silicon substrate for good power dissipation
The CTN series is a center tapped nichrome resistor chip
providing excellent stability at 250 mW power levels. The
CTN offers the designer flexibility in use as either a single
value resistor or as two resistors with a center tap feature.
The CTNs six bonding pads allows the user increased layout
flexibility.
The CTNs are manufactured using Vishay Electro-Films
(EFI) sophisticated thin film equipment and manufacturing
technology. The CTNs are 100 % electrically tested and
visually inspected to MIL-STD-883.
APPLICATIONS
The CTN center-tapped resistor chips are used mainly in feedback circuits of amplifiers where ratio matching, high power and
tracking between two resistors is critical.
Recommended for Hermetic environment where die is not exposed to moisture.
For low values, the resistance of the six bonding-pad configurations can vary, depending on the method of measurement used.
Vishay EFI measures low-value resistors by the four wire Kelvin technique.
TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES AND TOLERANCES
Tightest Standard Tolerance Available
0.5 %
0.1 %
± 10 ppm/°C
± 25 ppm/°C
± 50 ppm/°C
± 100 ppm/°C
PROCESS CODE
CLASS H*
203
202
200
201
*MIL-PRF-38534 inspection criteria
1 MΩ
CLASS K*
263
262
260
261
10
Ω
100
Ω
200
Ω
1 kΩ
STANDARD ELECTRICAL SPECIFICATIONS
PARAMETER
TCR Tracking Between Halves (R
A
/R
B
)
Center Tap Ratio,
R
A
/R
B
Tolerance
Noise, MIL-STD-202, Method 308, 100
Ω
- 250 kΩ
Stability, 1000 h, + 125 °C, 125 mW
Operating Temperature Range
Dielectric Voltage Breakdown
Insulation Resistance
Operating Voltage
DC Power Rating at + 70 °C (Derated to Zero at + 175 °C)
* 20 ppm/°C for
R
< 20
www.vishay.com
76
For technical questions, contact: efi@vishay.com
Document Number: 61024
Revision: 12-Mar-08
± 2 ppm/°C *
1 ± 1 % standard
- 35 dB typ.
± 0.1 %
ΔR/R
- 55 °C to + 125 °C
200 V
10
12
min.
100 V max.
250 mW
Errors 1033 and 1041 occurred during Win CE6.0 customization
1\cepcstrings.pbcxml"). D:\WINCE600\platform\ICOP_eBox4300_60DS\catalog\1041\cepcstrings.pbcxml 0 0 Error 2 Catalog Id "StringTable:MS:Cepc:1041" duplicated in files "D:\WINCE600\platform\CEPC\catalog...
jiuzhouliujun Embedded System
Let's discuss a topic that has not been mentioned in this forum - oscilloscope batteries
I used an oscilloscope to observe a small signal these days and found that there was power frequency interference. After analysis, I found that it can only be eliminated by using a battery. I asked ab...
xcuresme Test/Measurement
MSP430F149 Circuit Connection
I have two input control signals and want to send them to msp430f149 as output control signals through UART. How should I connect the circuit? Thank you very much......
yanyaqi88 Microcontroller MCU
The latest development of electronic devices (IGBT modules)
[color=#1919f8]1. High-power Trench Gate IGBT Module[/color] The IGBT cells in today's high-power IGBT modules usually use trench gate IGBTs. Compared with the planar gate structure, the trench gate s...
guangqiji PCB Design
About max1534 power chip
I used a max1534 power chip with three fixed outputs: 5V, 3V3, and 1.8. However, after loading, the 5V was pulled down to about 2V. Is there something wrong? The circuit is the recommended circuit in ...
xiaoqzq Power technology
Some questions about stm32 receiving GPS module data
[i][i][i][i][i][i][i][i][i][i][i][i][i][i][i][i][i][i][i][i][i][i][i][i][i][i][i][i][i]I have been debugging the GPS module for the past two days, but it has not been able to display on the LCD. I hav...
冷板凳 stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2546  1819  2308  184  2065  52  37  47  4  42 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号