I would like to ask how do you program this capacitive touch button diagram? I am a beginner and hope you can take care of me! ! ! ! [[i] This post was last edited by weiyubian on 2011-7-23 18:05 [/i]...
I use MAX10 to configure Arria10. MAX10 has an external 512Mbit NorFlash. I use PFL IP to configure Arria10 in MAX10. There is also an ARM bus that can burn Arria10 configuration files into NorFlash. ...
Hello everyone, I have a battery charger at home with a maximum of 30A. The positive and negative poles are divided into red and blue lines. Sometimes, if the positive and negative poles are connected...
Abstract: This paper briefly introduces the XC9500 series CPLD devices and their in-system programming (ISP) performance, and then describes the implementation method of remote control programming of ...
I wrote a simple key driver (stream driver), added it to the project created by 2440 BSP, modified the interrupt settings in cfw.c and armint.c, and changed the registry (when adding dll to the bib fi...
[size=12px]Help needed: 230MHz wireless transmitter and receiver debugging! High reward! [size=13px][size=12px]I am in the process of making a 230MHz wireless transmitter and receiver (transmitter pow...
The Portable Digital Data Acquisition System (PDDAS) uses LabVIEW Real-Time and PXI to control the wind tunnel test and record air pressure data from 128 different channels.
"The LabVIEW Real-...[Details]
System design is a complex process. It is not enough to just use ICs. There are many details to consider. This article uses a high-fidelity music playback system as an example to introduce how to s...[Details]
Abstract: In order to generate a stable excitation signal, the design of a digital frequency synthesizer is implemented on FPGA using Verilog hardware language. The design includes accumulator, wav...[Details]
1. Introduction
With the gradual automation and modernization of industrial control systems, fieldbus control systems have received more and more attention and application. CAN bus is currentl...[Details]
From the PIC16F946 datasheet, we know that there are two ways to write values to the LCD for display:
1. Directly write the value to LCDDATA1~LCDDATA23
2. Use disconnect t...[Details]
Editor's note: In order to help technicians or engineers who have knowledge of PIC microcontroller assembly language quickly master the method of using C language to program PIC microcontrollers, t...[Details]
1 Introduction
The Third Steel Plant of Jigang Group is a key investment project of Jigang Group during the "15th Five-Year Plan". It has introduced first-class domestic and foreign advanced eq...[Details]
This controller uses PIC16C54 single-chip microcomputer as the controller, and it is very easy to use: just connect a telephone line to the loudspeaker through the controller, and you can rem...[Details]
Capacitors
are basic components in various electronic devices and are widely used for bypassing, coupling,
filtering
, tuning, etc. in electronic circuits. However, to use capacitors,...[Details]
introduction
MEMS is a high-tech that has flourished on the basis of integrated circuit production technology and dedicated micro-electromechanical processing methods. Pressure sensors develop...[Details]
With the rapid development of wireless
digital communication
, more challenges have been raised for integrated circuit design and testing. In the product design stage, in order to ensure
t...[Details]
In the "digital pressure measurement" experimental device of applied physics, the subject technical knowledge of analog circuits, digital circuits, sensors and single-chip microcomputers is used. In o...[Details]
The launch of Shenzhou IX is imminent, and Tiangong is welcoming visitors again. Yesterday, Professor Fu Qiang, Vice President of the Institute of Science and Industrial Technology of Harbin Instit...[Details]
1 Introduction to LED
With the development of science and technology, people have higher and higher requirements on automobile light sources. LED (Light Emitting Diode) has gradually attracted...[Details]
store
To prevent moisture, LEDs should be stored in a dry and ventilated environment with a storage temperature of -40°C to +100°C and a relative humidity below 85%.
The LED should be use...[Details]