EEWORLDEEWORLDEEWORLD

Part Number

Search

M55342M12B340DRT0

Description
Fixed Resistor, Thin Film, 0.1W, 340ohm, 50V, 1% +/-Tol, 300ppm/Cel, Surface Mount, 0603, CHIP
CategoryPassive components    The resistor   
File Size96KB,5 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

M55342M12B340DRT0 Overview

Fixed Resistor, Thin Film, 0.1W, 340ohm, 50V, 1% +/-Tol, 300ppm/Cel, Surface Mount, 0603, CHIP

M55342M12B340DRT0 Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid145084302161
package instructionSMT, 0603
Reach Compliance Codenot_compliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL8.05
Other featuresNON-INDUCTIVE
structureRectangular
JESD-609 codee0
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-65 °C
Package height0.8382 mm
Package length1.6256 mm
Package formSMT
Package width0.8128 mm
method of packingTR
Rated power dissipation(P)0.1 W
Rated temperature70 °C
GuidelineMIL-PRF-55342
resistance340 Ω
Resistor typeFIXED RESISTOR
size code0603
surface mountYES
technologyTHIN FILM
Temperature Coefficient300 ppm/°C
Terminal surfaceTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance1%
Operating Voltage50 V
E/H (Military M/D55342)
www.vishay.com
Vishay Dale Thin Film
QPL MIL-PRF-55342 Qualified
Thin Film Resistor, Surface-Mount Chip
FEATURES
• Established reliability, “S” and “V” failure rate level
(10 ppm), C = 2
• High purity alumina substrate
• Wraparound termination featuring a tenacious adhesion
layer covered with an electroplated nickel barrier layer for
+150 °C operating conditions
LINKS TO ADDITIONAL RESOURCES
• Very low noise and voltage coefficient
(< -25 dB, 0.5 ppm/V)
• Non-inductive
• Laser-trimmed tolerances ± 0.1 %
• Wraparound resistance less than 0.010
Ω
typical
• In-lot tracking less than 5 ppm/°C
• Complete MIL-testing available in-house
• Antistatic waffle pack or tape and reel packaging available
• Military / aerospace / QPL
D
D
3
3
3D Models
Thin Film Mil chip resistors feature all sputtered wraparound
termination for excellent adhesion and dimensional
uniformity. They are ideal in applications requiring stringent
performance requirements. Established reliability is assured
through 100 % screening and extensive environmental lot
testing.
CONSTRUCTION
Passivation
Resistor Film
Solder
Coating
Nickel Barrier
High Purity
Alumina Substrate
Adhesion Layer
TYPICAL PERFORMANCE
ABSOLUTE
TCR
TOL.
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Resistance Range
TCR: Absolute
Tolerance: Absolute
Stability: Absolute
Stability: Ratio
Voltage Coefficient
Working Voltage
Operating Temperature Range
Storage Temperature Range
Noise
Shelf Life Stability: Absolute
SPECIFICATIONS
Tamelox resistor film (passivated nichrome)
10
Ω
to 6.19 MΩ
± 25 ppm/°C to ± 300 ppm/°C
± 0.1 %, ± 0.25 %, ± 0.5 %, ± 1 %,
± 2 %, 5 %, ± 10 %
ΔR
± 0.02 %
-
0.1 ppm/V
30 V to 200 V
-65 °C to +150 °C
-65 °C to +150 °C
< - 25 dB
ΔR
± 0.01 %
CONDITIONS
-
-
-55 °C to +125 °C
+25 °C
2000 h at +70 °C
-
-
-
-
-
-
1 year at +25 °C
Revision: 15-Nov-2021
Document Number: 60018
1
For technical questions, contact:
thinfilm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Launchpad430--TIMER--Series 1 written for you
[b]Technical description[/b][color=#000][font=Arial][/font][/color] [color=#000][font=Arial][size=18px]As shown in the figure. . . Before using the timer, we should first know what we will use this ti...
qinkaiabc Microcontroller MCU
lm3s101 gpio port interconnection problem
The situation is like this, I use pa0 to send a square wave signal with a period of 100us, and use pa1 to receive it, with a 39k resistor connected in the middle. Why is the low level of the signal de...
sciencekn1 Microcontroller MCU
Showing the process of WEBENCH design + high brightness LED design 1
In this design software, after selecting LED ARCHITECT, you can enter the lumen brightness design interface. According to my design requirements, I set the initial input voltage to 12V between 10-14V ...
accboy Analogue and Mixed Signal
Newbie help... MSP430 MCU controls LCD display
How to control LCD with MCU? I am using MSP430f149 MCU, and now I need to code on this board to control the LCD to display something. Can you give me some ideas on how to do it? I don't know where to ...
fzuyoup Embedded System
How to measure the lower frequency in multisim
As the title says, the digital electronics experiment requires making a simple digital clock. After 555 oscillation, the frequency of 1khz is obtained. After 74ls90 division, three 90 strings divide i...
纠结者 Analog electronics
After setting the "owner" information in the wince control panel, the information disappears after restarting the phone
Where are these defaults stored? Where should I change them?...
qy7551693 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2051  493  106  576  555  42  10  3  12  19 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号