501P51N241JK3H datasheet, PDF - EEWORLD Datasheet

501P51N241JK3H: DescriptionCeramic Capacitor, Ceramic, 500V, 5% +Tol, 5% -Tol, NP0, -/+30ppm/Cel TC, 0.00024uF,; CategoryPassive components capacitor; File Size836KB，6 Pages; ManufacturerJohanson Dielectrics

Download Datasheet Parametric View All

501P51N241JK3H Overview

Ceramic Capacitor, Ceramic, 500V, 5% +Tol, 5% -Tol, NP0, -/+30ppm/Cel TC, 0.00024uF,

Parameter Name	Attribute value
Objectid	865680903
package instruction	,
Reach Compliance Code	compliant
ECCN code	EAR99
YTEOL	6.7
capacitance	0.00024 µF
Capacitor type	CERAMIC CAPACITOR
dielectric materials	CERAMIC
high	19.304 mm
JESD-609 code	e0
length	51.118 mm
negative tolerance	5%
Number of terminals	2
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package form	SMT
positive tolerance	5%
Rated (DC) voltage (URdc)	500 V
series	P(SMT)
Temperature characteristic code	NP0
Temperature Coefficient	30ppm/Cel ppm/°C
Terminal surface	Tin/Lead (Sn60Pb40)
width	12.7 mm

Friendly Arm MINI2440 User Manual: [b]Contents[/b] Chapter 1 Introduction to MINI2440 Development Board...................................................................................- 11 - 1.1 Introduction to MINI2440 Development B...; clark Embedded System

LPC2368 xmodem bootloader program problem: I have made a bootloader program for LPC2368 xmodem. The design idea is to store two independent projects in the LPC2368's on-chip FLASH. After powering on, the first program is run, which is stored i...; eeleader MCU

Environmental online monitoring products based on Hercules TMS570: [table=500] [/table]...; dzc2001 Microcontroller MCU

Please advise on the short-circuit protection of DA output (urgent): I have designed a signal source with an amplitude of +-5V using FPGA and DAC8734. The short-circuit current of DAC8734 is 10mA, but I cannot find a thermistor with such a small current. Is there any s...; guolei1019 Analogue and Mixed Signal

ST7565 Serial Driver: /* In the serial drive mode, the only thing to note is that although the WR and RD pins are not used, they must be grounded, otherwise the display will not be normal; /**************************Prepro...; eeleader NXP MCU

How to re-program the program with STVisualProgrammer after STM8 is protected: After STM8 is protected, how can I use ST Visual Programmer to re-program the program? Please give me some advice, I will be very grateful!...; chifeng0823 stm32/stm8

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components