All temperatures refer to topside of the package, measured on the package body surface.
260°C Reflow Profile
W
&
W &
3°C/seconds max.
150°C
200°C
60-180 seconds
3°C/seconds max.
217°C
60-150 seconds
max 260°C
Time within 5°C of actual
Peak Temperature (tp)
Ramp-down Rate
6°C/seconds max.
20-40 seconds max.
W
&
W &
8 minutes max.
Average ramp-up rate (TL to TP)
Preheat - Temperature min Tsmin
- Temperature min Tsmax
- Time (min to max) (ts)
Tsmax to TL -Ramp-up Rate
Time maintained above - Temperature (TL)
- Time (TL)
Peak Temperature (Tp)
E
Time 25°C to Peak Temperature
Time maintained above
- Temperature (TL)
- Time (tL)
217°C
60-150 seconds
All temperatures refer to topside of the package, measured on the package body surface.
4 of 5
Ordering Information
EX - 421 0 - D A P - 108 0 - 10M0000000
Frequency
Frequency Control
Configuration
Thru-hole
Stability Code
Supply Voltage
508: ±50ppb
758: ±75ppb
107: ±100ppb
6: Fixed Frequency (+5 dBm)
7: Electrical Tuning (+5 dBm)
d
d
^
Z
Z
^
&
&
d
^
d
108 (+/-10ppb)
208 (+/-20ppb)
308 (+/-30ppb)
508 (+/-50ppb)
758 (+/-75ppb)
107 (+/-100ppb)
A: -55°C to +85°C E: -40°C to +85°C J: -20°C to +70°C P: 0°C to +50°C
10-20MHz
10-20MHz
10-50MHz
10-80MHz
10-100MHz
10-20MHz
10-50MHz
10-100MHz
10-20MHz
10-20MHz
10-50MHz
10-100MHz
10-20MHz
10-20MHz
10-50MHz
10-100MHz
Aging Table
Notes:
(+/-10ppb)
1.
208 (+/-20ppb)
2.
308 (+/-30ppb)
4.
frequencies.
10-30MHz
10-30MHz
10-30MHz
Subject to technical modification.
Contact factory for availability.
For Additional Information, Please Contact
USA:
Vectron International
Europe:
Vectron International
Asia:
Vectron International
Disclaimer
Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application.
No rights under any patent accompany the sale of any such product(s) or information.
【My environment】: Friendly mini2440, using the 5.0 BSP provided by the manufacturer, XP SP3 + PB5 + Wince5, and made an i2c driver by myself. 1. Compiled successfully under the release version, confir...
[table][tr][td]The microcontroller used is STC12C5410AD. I set the baud rate to 9600bps, but the serial port debugging assistant requires it to be changed to 4800bps to barely receive most of the data...
Active balancing and passive balancing are hot issues in the electric vehicle BMS industry. It is just like the Qi Sect and the Sword Sect of Huashan Sword Sect. People in the industry are arguing abo...
There are computers, soldering irons, switching power supplies and other electrical appliances on the same socket. I use a switching power supply (24V) to power the circuit board. I found that when th...
Microchip's PIC18F46J50 is a low-power, high-performance 8-bit USB microcontroller (MCU) using nanoWatt XLP technology. The current in deep sleep mode can be as low as 13nA, the operating voltage i...[Details]
As a wireless broadband metropolitan area network standard, WiMAX technology has greater advantages than previous 3.5GHz MMDS products in terms of non-line-of-sight transmission and spectrum utiliz...[Details]
All electronic design engineers and scientists have performed electrical signal analysis, or signal analysis for short. Through this basic measurement, they can gain insight into signal details and...[Details]
I. Introduction
In the field of power conversion, isolated converters (forward, flyback, and double-ended) with low output DC voltage all use MOSFET as the rectifier device. Since these devi...[Details]
Two simple circuits are implemented to drive two LEDs from a battery powered microprocessor.
This design is based on a circuit that uses three resistors and a microprocessor I/O pin as an input h...[Details]
1. Introduction
At present, most lighting equipment still uses traditional energy for lighting. Making full use of solar energy as the energy supply for lighting equipment is of great si...[Details]
Microcalorimetry
is used to determine energy relationships. Microcalorimetry techniques are often required when performing calorimetric experiments with small sample sizes or slow heating rat...[Details]
Overview:
This paper introduces a method of connecting a CAN-bus network with Ethernet to form a medium-sized remote monitoring/data transmission network.
CAN (Controller Area Network) is ...[Details]
Many battery-powered systems require a visual indicator to show when the battery needs to be replaced. LEDs are commonly used for this purpose, but they consume at least 10mA of current. This con...[Details]
Problems such as the depletion of natural resources, air pollution, traffic congestion, and rising fossil fuel prices have forced societies and individuals to seek alternative means of transportati...[Details]
In today's body control module (BCM) designs, savvy engineers are moving away from electromechanical relays whenever possible. Their next step is to eliminate fuses. But is eliminating fuses a nece...[Details]
Motors, especially those with brushes, generate a lot of noise. This noise must be dealt with if the appliance is to meet the requirements of EMC standards. The means to solve EMC are nothing more ...[Details]
Abstract: With the development and construction of BeiDou II system, China will shift from the situation dominated by GPS to the situation dominated by BeiDou II global navigation system independen...[Details]
LED is the abbreviation of the English word. Its main meanings are: LED = Light Emitting Diode, a solid-state semiconductor device that can convert electrical energy into visible light. It can dire...[Details]
Nowadays, more and more people have digital cameras. The convenience and speed of digital cameras have gradually replaced film cameras and become the main tool for people's daily photography. The n...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
