Custom Bumpon products may require a qualifying minimum quantity and/or a one time set-up charge. Call your local 3M sales
representative for more information.
(3)
3M
™
Bumpon
™
Protective Products
- Molded Shapes - Colored and Clear
Series SJ5000
•
SJ5300
•
SJ5400
•
SJ5500
•
SJ5700
•
SJ6100
Typical Physical Properties and Performance Characteristics
Note:
he following technical information and data should be considered representative or typical only and should
T
not be used for specification purposes.
Hardness, Shore M
Resilience, %
Kinetic Coefficient of Friction (Mk)
(Dependent on Test Surface)
1
3M Test Method
4
ASTM-D2240
ASTM-D2632,
0.125" sample
ASTM-D1894
Stainless Steel
Glass
Formica
®
laminate
Wood
ASTM-C501
3M™ Bumpon™ Protective Products
SJ5000
SJ5500
SJ5300
SJ5700
SJ5400
SJ6100
72
30
75
5
72
30
>1
>1
0.9-1.4
0.9-1.4
1.7-1.9
>1
>1
0.9-1.4
0.9-1.4
0.13
>1
>1
0.9-1.4
0.9-1.4
1.7-1.9
Abrasion Resistance
(Taber H18, 1kg)
g/1000 cycles
2
Tensile, lbs/in
2
(MPa)
2
Elongation,%
2
Dielectric Strength,
volts/mil
2
Stain Resistance
3
ASTM-D412, Die A
ASTM-D412, Die A
ASTM-D1000
3M-24 hours @ 158°F
against white paint
7 days exposed to UV.
UL-94HB
600 (4.1)
100
200
No
Staining
Pass;
UL Recognized
740 (5.1)
65
370
No
Staining
Not UL
Recognized
600 (4.1)
100
200
No
Staining
Pass;
UL Recognized
Flammability Listing
Application Temperature
Service Temperature
Solvent and Fuel Resistance
3
5°C (40°F) to 52°C (125°F)
Constant:
Intermittent:
24 hour immersion
5% Detergent in water
25% Ammonia in water
Bleach
Hydrochloric Acid
(1 Normal Solution)
Diesel Fuel
Auto Oil
Isopropyl Alcohol
Heptane
Toluene (Toluol)
Lacquer Thinner
-34°C (-30°F) to 66°C (150°F)
Up to 107°C (225°F)
No Apparent Effect
No Apparent Effect
No Apparent Effect
No Apparent Effect
No Apparent Effect
No Apparent Effect
Slight Swelling
Slight Swelling
Considerable Swelling
Considerable Swelling
Notes:
1
Two important laws of friction applicable to Bumpon products are: (1) Friction is independent of the area of contact between solids and (2) friction is
proportional to the load between solid surfaces. Thus, if the load (weight) is doubled the force required to cause sliding is also double. This is expressed
mathematically as follows: Sliding Force = Mk x weight.
2
These properties were run on sheet material from the same materials as the individual Bumpon products
3
Reference test for 24 hours. Results may vary for different product application conditions.
4
When ASTM method is listed, data was collected in accordance with ASTM test method.
(4)
3M
™
Bumpon
™
Protective Products
- Molded Shapes - Colored and Clear
Series SJ5000
•
SJ5300
•
SJ5400
•
SJ5500
•
SJ5700
•
SJ6100
Relative Adhesive Performance Characteristics
Note:
he following technical information and data should be considered representative or typical only and should
T
not be used for specification purposes.
Adhesive:
Initial Adhesion
Low Surface Energy:
High Surface Energy:
Adhesion (Peel)
Low Surface Energy:
High Surface Energy:
Static Shear
25°C (75°F):
49°C (120°F):
70°C (158°F):
Dynamic Shear:
Solvent Resistance:
SJ5000
SJ5500
SJ5700
Natural Rubber
R-30
Good
Good
Good
Good
Excellent
Good
Poor
Good
Good
3M™ Bumpon™ Protective Products
SJ5300
SJ5400
Acrylic
A-20
Poor
Fair
Poor
Good
Excellent
Excellent
Excellent
Excellent
Excellent
SJ6100
Synthetic Rubber
R-25
Excellent
Excellent
Excellent
Excellent
Excellent
Good
Fair
Good
Good
Adhesive Performance
Note:
he following technical information and data should be considered representative or typical only and should
T
not be used for specification purposes.
The following table on peel adhesion provide representative performance characteristics of the adhesive
systems used in the construction of 3M™ Bumpon™ Protective Products molded series products.
90° Peel Adhesion
Substrate:
Polypropylene
Polystyrene
ABS
Stainless Steel
Aluminum
SJ5000
SJ5500
SJ5700
Natural Rubber
R-30
25
25
25
22
22
*Peel Force, oz. Per 1/2 inch
3M™ Bumpon™ Protective Products
SJ5300
SJ5400
Acrylic
A-20
3
11
25
25
25
SJ6100
Synthetic Rubber
R-25
52
55
55
55
55
*
M Test Method TM-2011; 72 hour dwell, 1/2 inch wide samples pulled at 12 inches per minute. Testing completed using Bumpon Resilient Rollstock
3
products SJ5816, SJ6016, and SJ6216, which use the same adhesive system as the molded series products.
The target value is reduced to about -110V. Figure 1 shows the secondary winding RCD circuit parameters of the auxiliary power supply. The output is 12V, about 5A, the total output power is about 70W,...
Urgent...! Does anyone know the assembly language of a multifunctional electronic keyboard that can realize the eight-tone and music playback functions. It can also select songs and stop. Thanks!...
I wanted to design a -3V output circuit using LT1931A. Why is the -3V output of the out port unstable and fluctuates by about 1V? See the picture for details. Can any experts give me some advice? ! !...
I want to learn operating systems by myself, but people around me say that it is difficult to learn by myself and it is better to attend training. Friends, please give me some suggestions! How did you...
Is there any information about the thermistor on the Ferroelectric MSP-EXP430FR5739? For example, the B value or something? Has anyone used the thermistor mentioned above in detail? How accurate can t...
Limited vocabulary recognition
According to the number of characters, words or short sentences in the vocabulary, it can be roughly divided into: less than 100 is small vocabulary; 100-1000 is...[Details]
On August 25th, TSMC, the world's leading contract chip manufacturer, attracted significant attention for its decision to build a chip manufacturing facility in Arizona. TSMC primarily manufactures...[Details]
Definition of interactive projection system:
Interactive projection systems, also known as multimedia interactive projection, are available in floor, wall, and tabletop interactive projection....[Details]
On August 22nd, Lantu Motors unveiled a new technology called "Lanhai Intelligent Hybrid" during a live broadcast of CCTV News' "Top Laboratory." The name sounds like another new term, but a closer...[Details]
On August 21st, Zhiyuan Robotics revealed at its first partner conference that it expects shipments to reach thousands of units this year and tens of thousands next year. The company hopes to reach...[Details]
Electric vehicles' 12V batteries don't rely on a generator to power them. Only gasoline-powered vehicles rely on the engine to drive a generator to generate electricity while driving, which is used...[Details]
SMT placement machines are important equipment in surface mount technology (Surface Mount Technology). Their performance has a decisive impact on the quality and efficiency of electronic manufactur...[Details]
Reflow soldering, as an electronics assembly process, has become a vital component of the electronics manufacturing industry. Choosing reflow soldering equipment is crucial for improving production...[Details]
"We have successfully launched the first version of our dedicated chip for EMB brake-by-wire. Second-generation samples have also been successfully completed, and we are actively planning a third-g...[Details]
Recently, Joyson Electronics has made positive progress in the core technology research and development of the robot's "brain and brain" and key components, and launched the industry's first integr...[Details]
Lightweighting of automobiles is still a relatively unfamiliar term for automobiles. With the continuous improvement of environmental protection requirements, relevant regulations have also put for...[Details]
As the range of electric vehicles continues to increase, driving electric vehicles for long-distance travel has become a trend. For high-speed travel, how much impact will high-speed driving of ele...[Details]
Facial recognition, a biometric technology that uses facial features to authenticate identity, has rapidly become a global market hotspot in recent years as the technology has entered practical use...[Details]
On August 18th, China's largest expressway
charging station,
the G25 Changshen Expressway Tonglu Service Area (South Area), officially opened and launched its integrated solar-storage-charg...[Details]
The screen is the first thing you notice when evaluating a phone's quality. Its quality directly impacts both visual and operational performance. However, understanding mobile phone screens r...[Details]
_pdf/pg_0001.png)
Analog electronics
京公网安备 11010802033920号
EEWORLD_pdf/1.png)
_pdf/2.png)
_pdf/3.png)
_pdf/4.png)
_pdf/5.png)
_pdf/pg_0002.png)
_pdf/pg_0003.png)
_pdf/pg_0004.png)
_pdf/pg_0005.png)
