Ultra-Small, Ultra-Low Power MEMS Oscillator with Spread Spectrum
Features
• Output Frequency: 1 MHz to 100 MHz LVCMOS
• Spread Spectrum Options:
- Center-Spread: ±0.25%, ±0.5%, ±1.0%,
±1.5%, ±2.0%, ±2.5%
- Down-Spread: –0.25%, –0.5%, –1.0%,
–1.5%, –2.0%, –3.0%
• Ultra-Low Power Consumption: 3 mA (Active),
1
A (Standby)
• Wide Supply Voltage Range: 1.71V ~ 3.63V V
DD
• Ultra-Small Package Sizes:
- 1.6 mm
1.2 mm
- 2.0 mm
1.6 mm
- 2.5 mm
2.0 mm
• Wide Temperature Range:
- Automotive: –40°C to +125°C
- Ext. Industrial: –40°C to +105°C
- Industrial: –40°C to +85°C
- Ext. Commercial: –20°C to +70°C
• Excellent Shock and Vibration Immunity
- Qualified to MIL-STD-883
• High Reliability
- 20x Better MTBF than Quartz Oscillators
• Lead Free and RoHS Compliant
• Automotive AEC-Q100 Option Available
General Description
The DSC63xxB family of devices is the industry’s
smallest and lowest-power spread-spectrum MEMS
oscillators. Available in three different package sizes
with operating current as low as 3 mA, the smallest
4-pin package is a mere 1.6 mm x 1.2 mm in size. The
devices support up to ±2.5% or –3% spread spectrum
that can achieve up to 15 dB electromagnetic
interference (EMI) reduction. Because of industry
standard package and pin options, customers can
solve last minute EMI problems simply by placing the
new DSC63xxB on their current board layout with no
redesign required.
The DSC63xxB family is available in 1.6 mm x 1.2 mm
and 2.0 mm x 1.6 mm, and 2.5 mm x 2.0 mm
packages. These packages are “drop-in” replacements
for standard 4-pin CMOS quartz crystal oscillators.
Package Types
DSC63
XX
B
2.5 mm x 2.0 mm VLGA
2.0 mm x 1.6 mm VFLGA
1.6 mm x 1.2 mm VFLGA
(Top View)
OE/STDBY/SSEN
1
4
VDD
Applications
•
•
•
•
Flat Panel Display/Monitor
Multi-Function Printer
Digital Signage
Consumer Electronics
GND
2
3
OUT
2019 Microchip Technology Inc.
DS20006154A-page 1
DSC63XXB
Block Diagram
DSC63
XX
B
DIGITAL
CONTROL
OE/STDBY/SSEN
PIN 1
SST
MEMS
RESONATOR
TEMP SENSOR
CONTROL &
COMPENSATION
PLL
VCO
SUPPLY
REGULATION
VDD
PIN 4
OUTPUT
DIVIDER
DRIVER
OUTPUT
PIN 3
GND
PIN 2
DS20006154A-page 2
2019 Microchip Technology Inc.
DSC63XXB
1.0
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings
Supply Voltage .......................................................................................................................................... –0.3V to +4.0V
Input Voltage (V
IN
) ..............................................................................................................................–0.3V to V
TI's official I2C program uses interrupt mode, and its actual operation has various problems. Is there any I2C program that can be used to read and write AT24C02?...
The title seems like writing an essay :). I opened the forum and saw that I could watch a movie, so I immediately bought two tickets and went to the movie with my girl. Sigh, I originally wanted to wa...
1. Set the pin multiplexing register PINMUX8 and select the function of pin 3 as timer output. Note that this pin coincides with the SCL of I2C0.
(User Manual P203)
2. Set up the timer setup_TIMER0();...
I have been working in asp.net for several years and have joined many technical exchange groups. In these groups, I see that the group leaders are always so enthusiastic in answering questions, but ma...
The circuit diagram and program are as follows; the original intention is to control the digital tube to display 0-a incrementally, and the timer controls the flashing of the LED. When the button is p...
1-2-3. Calculation of the energy storage filter inductor of the series switching power supply From the above analysis, it can be seen that the output voltage Uo of the series switching power supply is...
On April 20, the Photovoltaic Summit, guided by Jiangsu Renewable Energy Industry Association, hosted by Growatt, and supported by LONGi Solar Technology Co., Ltd. and Jiangsu Bigo New Energy Group...[Details]
1. Purpose Since the number of times the STM32 FLASH can be erased and written is limited, in order to protect our FLASH and extend the use time of the MCU, we can debug on the SRAM. SRAM is a ...[Details]
1. Usage scenarios In the first case, when using a common STM32 delay function, similar to HAL_Delay(time), since this function uses a loop to judge and delay, when executing this function, the ent...[Details]
0. Preparation First use st-link to connect the stm32 core board and PC for burning St-link Stm32 3.3V 3.3V GND GND SWDIO PART SWCLK DCLK Then connect with USB serial port board to v...[Details]
The last two blogs talked about a version problem of STM32CubeMX and the problem of hardware reset. When you solve these two problems, you will find that after the program is burned into the board, t...[Details]
Automotive LCD Instrument Clock EMI Solution As early as 2014, the market size of China's automotive full LCD instrument has reached 3.506 billion yuan, and it is expected that by 2020, this s...[Details]
China Energy Storage Network News:
On the 7th, Jurong Economic Development Zone signed a strategic cooperation framework agreement on comprehensive energy services with State Grid Jiangsu Int...[Details]
China Energy Storage Network News:
"As the world's first third-generation blockchain, Anda Chain, which has China's independent intellectual property rights, will be launched globally in the ...[Details]
1) Independent watchdog has no interrupt, window watchdog has interrupt 2) Independent watchdogs can be divided into hardware and software, while window watchdogs can only be controlled by software...[Details]
Google may have foreseen the spread of artificial intelligence (
AI
) technology across apps, devices, and services, such as recognizing friends' faces in photos and giving smart speakers h...[Details]
Example analysis: (using DMA mode) mian function: extern __IO u16 ADC_ConvertedValue; //The voltage value converted by ADC is defined in the context of ADC1_Init() float ADC_ConvertedValueLocal; ...[Details]
The key is the configuration of registers. The T1 timer (16 bits) of CC2530 needs to configure three registers: T1CTL, T1STAT, IRCON Here is just a brief introduction. For more details, please refer ...[Details]
MCS-51 single-chip microcomputer timer/counter experiment programming program Programming requirements: 1. Connect a light-emitting diode LED to the P1.0 pin, light up for two seconds, turn off for o...[Details]
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
