Standard Frequencies – see Page 5 for developed frequencies.
* Check with factory for availability of frequencies not listed.
pplications
utomotive Electronics
Mobile Multimedia/Infotainment
Car Navigation Systems
Internet of Things [IoT, IIot]
Microcontrollers and FPG s
Wireless Communication
Ethernet/GbE/SyncE
Medical Electronics
Commercial Military & erospace
Description
CTS Model S 5 2 incorporates a low cost, high Q, small size quartz resonator specifically developed to operate
over extended temperature ranges for use in automotive electronics.
Ordering Information
Model
S 5 2
Frequency Code
[MHz]
X X X or X X X X
Mode of
Oscillation
F
Tolerance
@ +25°C
Temperature
Stability
5
Temperature
Range
G
Load
Capacitance
Packaging
T
Code
Frequency
Product Frequency Code
1
Code
1
X
2
5
Tolerance
±10ppm
±15ppm
±20ppm
± 0ppm
±50ppm
Code
I
G
H
N
P
M
Stability
±15ppm
±20ppm
± 0ppm
Code
5
6
7
Temp. Range
2
-40°C to +85°C
-40°C to +105°C
4
-40°C to +125°C
-40°C to +150°C
5
5
-55°C to +105°C
-55°C to +125°C
5
Packing
Code
1k pcs./reel
T
Code
F
T
Mode
Fundamental
rd Overtone
Code
X
2
Stability
±50ppm
±100ppm
±150ppm
Code Capacitance Code Capacitance
7pF
16pF
V
C
8pF
18pF
K
D
9pF
20pF
J
E
10pF
24pF
F
12pF
0pF
L
G
1 pF
Series
B
S
Notes:
1]
2]
]
4]
5]
Refer to document 016-1454-0, Frequency Code Tables. -digits for frequencies <100MHz, 4-digits for frequencies 100MHz or greater.
vailable with all stability codes.
vailable with stability codes , 5, 6 and 7.
vailable with stability codes 5, 6 and 7.
Stability codes 6 and 7. Contact factory for code 5 availability.
Not all performance combinations and frequencies may be available.
Contact your local CTS Representative or CTS Customer Service for availability.
This product is specified for use only in standard commercial applications. Supplier disclaims all express and implied warranties and liability in connection with any use of this
product in any non-commercial applications or in any application that may expose the product to conditions that are outside of the tolerances provided in its specification.
STMicroelectronics (ST) has decided to expand its ultra-small low-G linear acceleration sensor and launched the low-power, low-cost 3-axis acceleration sensor "LIS302ALK". This product is a small MEMS...
2015 Fall ## University Electronic Design Competition Topic: Digital DC Microampere Ampere Meter Design and make a digital display DC ammeter. The specific requirements are as follows: 1. Basic requir...
After much hardship, I changed my career from hardware to software, and finally found a job. It was a bad job, but I had no choice but to accept it. However, after finding the job, a serious problem e...
The results of the postgraduate entrance examination were announced in January. The results were neither good nor bad, which was worthy of myself. According to the previous admission scores of the Sch...
The rapid development of the Internet has realized high-speed information transmission and resource sharing, greatly facilitating people's lives. Embedded systems are widely used in various electr...[Details]
Traditional broadcasting systems generally need to be operated manually at a fixed time, and can only realize one-way broadcasting with few functions. Traditional bell ringing equipment has a singl...[Details]
In early 2002, I started to write a working program for an IC card prepaid electricity meter. The meter used Philips' 8-bit 51-expanded single-chip microcomputer
87LPC764
, and wa...[Details]
1. Circuit composition
The whole circuit consists of two parts:
1. Power saving control circuit
As shown in the figure below. Including delay circuit and drive circuit.
(1) Delay ci...[Details]
1. Introduction
With the growth of parking demand, the scale of parking lots is becoming larger and larger. A lot of research has been done on intelligent parking lots in China, but most of th...[Details]
Converged processors meet scalability requirements
In current embedded system design, solutions based on MCU, DSP, FPGA and ASIC account for more than 90% of the market share. These solutions ...[Details]
introduction
Solar cells and LED lighting are typical applications of new energy and energy-saving and efficient technologies. Solar LED lighting uses solar cells to convert solar energy...[Details]
In recent years, lighting has become an important area that countries around the world are targeting to promote energy conservation and environmental protection. According to statistics, about 20% ...[Details]
With the rapid development of urban economy, elevators are increasingly used as a vertical transportation tool. However, elevator fault detection and maintenance, especially the role of elevator remot...[Details]
A standard cell
is an electrochemical
cell
used as a voltage reference standard in many electrical standards laboratories
. If properly maintained, standard cells are very stable. The ...[Details]
1 Introduction
Intelligent control instruments are one of the most commonly used controllers in industrial control. They are mainly aimed at a specific parameter (such as pressure, tempera...[Details]
LED is the abbreviation of light emitting diode, which is an electric light source made of semiconductor technology. The core part of LED is a chip composed of P-type semiconductor and N-type semi...[Details]
The concept of state machine
State machine is an important concept in software programming. More important than this concept is its flexible application. In a clear and efficient program, ther...[Details]
With concerns about the growing energy crisis, motor efficiency has become an important and timely topic. This is because motors use 63% to 70% of the electricity produced in the United States and ...[Details]
It is well known to automotive suppliers that automakers are demanding more from their supply base. For connector suppliers, this means stricter requirements for product performance, stability and ...[Details]
Sensor
京公网安备 11010802033920号
EEWORLD
