Notes: (Ref) – Dimensions provided for reference only. No dimensions are provided for B, P or R because low profile cases do not have a bevel or a notch.
* MIL–PRF–55365/8 specified dimensions
Table 1 – Ratings & Part Number Reference
Rated
Voltage
VDC
4
4
4
6.3
6.3
6.3
10
16
16
16
20
25
25
35
35
35
VDC
Rated
Cap
µF
680
1000
1000
470
680
680
330
100
150
220
100
68
100
15
33
47
µF
Case Code/
Case Size
KEMET/EIA
X/7343-43
X/7343-43
E/7360-38
X/7343-43
X/7343-43
E/7360-38
X/7343-43
D/7343-31
X/7343-43
X/7343-43
X/7343-43
X/7343-43
E/7360-38
D/7343-31
X/7343-43
X/7343-43
KEMET/EIA
KEMET Part
Number
(See below for
part options)
T513X687(1)004(2)(3)(4)(5)
T513X108(1)004(2)(3)(4)(5)
T513E108(1)004(2)(3)(4)(5)
T513X477(1)006(2)(3)(4)(5)
T513X687(1)006(2)(3)(4)(5)
T513E687(1)006(2)(3)(4)(5)
T513X337(1)010(2)(3)(4)(5)
T513D107(1)016(2)(3)(4)(5)
T513X157(1)016(2)(3)(4)(5)
T513X227(1)016(2)(3)(4)(5)
T513X107(1)020(2)(3)(4)(5)
T513X686(1)025(2)(3)(4)(5)
T513E107(1)025(2)(3)(4)(5)
T513D156(1)035(2)(3)(4)(5)
T513X336(1)035(2)(3)(4)(5)
T513X476(1)035(2)(3)(4)(5)
(See below for
part options)
DC
Leakage
μA @ +20ºC
Max/5 Min
27.2
40.0
40.0
29.6
42.8
42.8
33.0
16.0
24.0
35.2
20.0
17.0
25.0
5.3
11.6
16.5
μA @ +20ºC
Max/5 Min
DF
% @ +20ºC
120 Hz Max
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
10.0
8.0
8.0
8.0
6.0
6.0
8.0
% @ +20ºC
120 Hz Max
Standard
ESR
mΩ @ +20ºC
100 kHz Max
30
23
18
30
45
23
35
75
40
40
45
45
50
100
65
65
mΩ @ +20ºC
100 kHz Max
Low ESR
mΩ @ +20ºC
100 kHz Max
N/A
18
10
N/A
23
12
N/A
N/A
30
25
40
N/A
N/A
N/A
55
55
mΩ @ +20ºC
100 kHz Max
Ultra-low
ESR
mΩ @ +20ºC
100 kHz Max
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
35
N/A
N/A
N/A
N/A
N/A
mΩ @ +20ºC
100 kHz Max
Rated Voltage
Rated
Cap
Case Code/
Case Size
KEMET Part Number
DC
Leakage
DF
Standard ESR
Low ESR
Ultra-low ESR
(1) To complete KEMET part number, insert M for ±20%, K for ±10%. Designates Capacitance tolerance.
(2) To complete KEMET part number, insert B (0.1%/1,000 hours), or A = N/A. Designates Reliability Level.
(3) To complete KEMET part number, insert B = Gold Plated, C = Hot solder dipped, H = Solder Plated, K = Solder Fused or T = 100% Tin (Sn). Designates
Termination Finish.
(4) To complete KEMET part number, insert 61 = None, 62 = 10 cycles +25°C, 63 = 10 cycles -55°C +85°C after Weibull or 64 = 10 cycles -55°C +85°C before
Weibull. Designates Surge current option.
(5) To complete KEMET part number, insert 10 = Standard ESR, 20 = Low ESR or 30 = Ultra Low ESR. Designates ESR option.
Refer to Ordering Information for additional detail.
When I use the capture mode of msp430f1611 to measure the frequency of a square wave, I find that the highest frequency that can be measured correctly does not exceed 200k. I use an 8M crystal oscilla...
I am currently using a spartan6 development board, and I have configured a microblaze soft core on this FPGA. In addition to the soft core, I also have other logics, such as a large module organized b...
[i=s]This post was last edited by zhanghuichun on 2015-11-11 21:05[/i] The collected YUY2 data is converted into RGB565 format and the displayed effect is unexpectedly like this.YUY2 to RGB565 code: [...
Can the memory of YLP2440 core board be expanded to 256M? YLP2440 core board has 64M RAM. Since the project needs to expand it to 256M, is this easy to implement? Is it enough to just add two address ...
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
