EEWORLDEEWORLDEEWORLD

Part Number

Search

51720-10202006AB

Description
Board Connector, Female, Right Angle, Solder Terminal, Locking, Receptacle
CategoryThe connector    The connector   
File Size272KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

51720-10202006AB Overview

Board Connector, Female, Right Angle, Solder Terminal, Locking, Receptacle

51720-10202006AB Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid309052224
Reach Compliance Codecompliant
ECCN codeEAR99
body width0.574 inch
subject depth0.93 inch
body length3.15 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact completed and terminatedTin/Lead (Sn/Pb)
Contact point genderFEMALE
Contact materialCOPPER ALLOY
Contact resistance2 mΩ
Contact styleHYBRID
Dielectric withstand voltage2500VDC V
Durability200 Cycles
maximum insertion force.973 N
Insulation resistance10000000000 Ω
insulator materialGLASS FILLED THERMOPLASTIC
JESD-609 codee0
Manufacturer's serial number51720
Mixed contactsYES
Installation option 1LOCKING
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
Maximum operating temperature105 °C
Minimum operating temperature-20 °C
Plating thickness30u inch
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.135 inch
Termination typeSOLDER
Evacuation force-minimum value.17792 N
PDM: Rev:P
STATUS:
Released
Printed: Dec 20, 2010
.
Electronic blood pressure monitor
I recently designed a wrist-type electronic blood pressure monitor! [/color] I think the size is too big. Can you introduce a smaller micro air pump? The performance requirement is 3V and the maximum ...
houyaojun2008 Medical Electronics
Altera FPGA's SDRAM clock processing problem
After reading so much information , I still don't know how to configure the clock output from FPGA to external SDRAM. Most of them should use one clk for the internal SDRAM controller of FPGA and anot...
eeleader-mcu FPGA/CPLD
Looking for a program to light up an LED
[i=s] This post was last edited by dontium on 2015-1-23 13:22 [/i] The F2812 board is ready, and it can be connected normally using the XDSUSB510 emulation. I burned a LED lighting program, and the bu...
loveitboy Analogue and Mixed Signal
Based on embedded linux operating system!!
How to connect the driver, qt, and dsp based on the embedded linux operating system and burn them into the board? ? Specific steps, thank you all! ! !...
renmingcan Linux and Android
How to transfer Q, I, and M registers to V register in PLC program?
[size=3]Please give me some advice on how to transfer Q, I, M registers to V register in PLC program[/size]...
eeleader Industrial Control Electronics
CCS3.3 Chinese Learning Manual
I have uploaded two Chinese learning manuals for CCS3.3, I hope they will be helpful to everyone!...
kooking DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1583  1125  234  1542  1214  32  23  5  25  11 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号