C0603Y472M2RACTU datasheet, PDF

Datasheet> All Categories > Passive components> C0603Y472M2RACTU

C0603Y472M2RACTU: Descriptionmultilayer ceramic capacitors mlcc - smd/smt 200volts 4700pf 20% x7r; CategoryPassive components; File Size3MB，20 Pages; ManufacturerKEMET; Websitehttp://www.kemet.com; Environmental Compliance

Download Datasheet Parametric View All

C0603Y472M2RACTU Overview

multilayer ceramic capacitors mlcc - smd/smt 200volts 4700pf 20% x7r

C0603Y472M2RACTU Parametric

Parameter Name	Attribute value
Manufacture	Keme
Product Category	Multilayer Ceramic Capacitors MLCC - SMD/SMT
RoHS	Yes
Capacitance	4700 pF
Voltage Rating	200 V
Tolerance	20 %
Temperature Coefficient / Code	+/- 15 %
Case Code - i	0603
Case Code - mm	1608
Operating Temperature Range	- 55 C to + 125 C
Produc	Open Mode/Fail-Safe MLCC
Dielectric	X7R
Maximum Operating Temperature	+ 125 C
Minimum Operating Temperature	- 55 C
Package / Case	0603 (1608 metric)
Packaging	Reel
Factory Pack Quantity	4000
Termination Style	SMD/SMT
Type	Floating Electrode Design with Flexible Termination System FF-CAP, X7R Dielectric, Commercial
Voltage Rating DC	200 V

Preview

Download Datasheet

View All

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)

Floating Electrode Design with Flexible Termination System

(FF-CAP), X7R Dielectric, 6.3 – 250 VDC (Commercial & Automotive Grade)

Overview

KEMET’s Floating Electrode with Flexible Termination capacitor

(FF-CAP) combines two existing KEMET technologies–

Floating Electrode and Flexible Termination. The floating

electrode component utilizes a cascading internal electrode

design configured to form multiple capacitors in series within

a single monolithic structure. This unique configuration results

in enhanced voltage and ESD performance over standard

capacitor designs while allowing for a fail-open condition if

mechanically damaged (cracked). The flexible termination

component utilizes a conductive silver epoxy between the base

metal and nickel barrier layers of KEMET’s standard termination

system in order to establish pliability while maintaining terminal

strength, solderability and electrical performance. Both

technologies address the primary failure mode of MLCCs– flex

cracks, which are typically the result of excessive tensile and

shear stresses produced during board flexure and thermal

cycling.

Although neither technology can eliminate the potential for

mechanical damage that may propagate during extreme

environmental and/or handling conditions, the combination of

these two technologies provide the ultimate level of protection

against a low IR or short circuit condition. The FF-CAP

complements KEMET’s Open Mode, Floating Electrode (FE-CAP),

Flexible Termination (FT-CAP) and KEMET Power Solutions (KPS)

product lines by providing an ultimate fail-safe design optimized

for low to mid range capacitance values. These devices exhibit a

predictable change in capacitance with respect to time and voltage

and boast a minimal change in capacitance with reference to

ambient temperature. Capacitance change is limited to ±15% from

-55°C to +125°C.

In addition to Commercial Grade, Automotive Grade devices

are available which meet the demanding Automotive Electronics

Council's AEC–Q200 qualification requirements.

Click image above for interactive 3D content

Open PDF in Adobe Reader for full functionality

Ordering Information

Ceramic

0805

104

Capacitance

Code (pF)

2 Significant

Digits + Number

of Zeros

Capacitance

Tolerance

J = ±5%

K = ±10%

M = ±20%

Voltage

9 = 6.3 V

8 = 10 V

4 = 16 V

3 = 25 V

5 = 50 V

1 = 100 V

2 = 200 V

A = 250 V

Dielectric

R = X7R

Packaging/Grade

(C-Spec)

Blank = Bulk

TU = 7" Reel

Unmarked

TM = 7" Reel Marked

Case Size

Specification/

(L" x W")

Series

0603

0805

1206

1210

1812

Y = Floating

Electrode

with Flexible

Termination

Failure Rate/

Termination Finish

Design

A = N/A

C = 100% Matte Sn

L = SnPb (5%

minimum)

Additional termination finish options may be available. Contact KEMET for details.

SnPb termination finish option is not available on automotive grade product.

Additional reeling or packaging options may be available. Contact KEMET for details.

1,2

One world. One KEMET

C1015_X7R_FF-CAP_SMD • 6/6/2014

Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)

Floating Electrode Design with Flexible Termination System (FF-CAP), X7R Dielectric, (Commercial & Automotive Grade)

Qualification/Certification

Commercial Grade products are subject to internal qualification. Details regarding test methods and conditions are referenced in

Table 4, Performance & Reliability.

Automotive Grade products meet or exceed the requirements outlined by the Automotive Electronics Council. Details regarding test

methods and conditions are referenced in document AEC–Q200, Stress Test Qualification for Passive Components. For additional

information regarding the Automotive Electronics Council and AEC–Q200, please visit their website at www.aecouncil.com.

Environmental Compliance

Lead (Pb)-Free, RoHS, and REACH compliant without exemptions (excluding SnPb termination finish option).

Electrical Parameters/Characteristics

Item

Operating Temperature Range

Capacitance Change with Reference to +25°C and 0 VDC Applied (TCC)

Aging Rate (Maximum % Capacitance Loss/Decade Hour)

Dielectric Withstanding Voltage

Dissipation Factor (DF) Maximum Limit @ 25ºC

Insulation Resistance (IR) Limit @ 25°C

-55°C to +125°C

±15%

3.0%

250% of rated voltage

(5 ±1 seconds and charge/discharge not exceeding 50 mA)

5% (6.3 and 10 V), 3.5% (16 and 25 V) and 2.5% (50 to 250 V)

See Insulation Resistance Limit Table

(Rated voltage applied for 120 ±5 seconds @ 25°C)

Parameters/Characteristics

Regarding aging rate: Capacitance measurements (including tolerance) are indexed to a referee time of 1,000 hours.

To obtain IR limit, divide MΩ-µF value by the capacitance and compare to GΩ limit. Select the lower of the two limits.

Capacitance and dissipation factor (DF) measured under the following conditions:

1 kHz ±50 Hz and 1.0 ±0.2 Vrms if capacitance ≤ 10 µF

120 Hz ±10 Hz and 0.5 ±0.1 Vrms if capacitance > 10 µF

Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 and Agilent E4980 have a feature known as

Automatic Level Control (ALC). The ALC feature should be switched to "ON."

C1015_X7R_FF-CAP_SMD • 6/6/2014

Recommended Resources

LA5511 principle block diagram and typical application circuit

Digital-to-time conversion circuit

Simulating natural wind circuit (2)

watchdog circuit

Inductive feedback oscillation circuit

875p computer motherboard circuit diagram_099

EEWORLD University ---- 2018 PSDS Seminar Series - (5) Common Errors and Solutions of DC-DC Converters: 2018 PSDS Seminar Series - (5) Common DC-DC Converter Errors and Solutions : https://training.eeworld.com.cn/course/4474...; hi5 Power technology

How to balance active and passive filters?: We often use filters. I would like to ask the experts, when to use active and passive filters? What is the difference between the two in application?...; 零下12度半 Analog electronics

485 Practical Problems and Solutions in Fieldbus Construction (2): 2. Terminal resistance method: Connect a 120 ohm terminal resistor to the 485+ and 485- of the last 485 device to improve the communication quality. 3. Intermediate segment disconnection method: Check...; 绿草 Industrial Control Electronics

[Help] How to embed the routing protocol into the CE protocol stack: rt Please provide me with a solution to embed the routing protocol into CE. I have just received such a job. I have never been involved in it. I would like to ask you what I need to learn and what pre...; weiyingwu Embedded System

[Old post ups and downs 3] Customize u8, uint8_t?: Surprisingly, after browsing the content of the last post, I found that the content it expressed was too much and too messy, and it had little to do with what I remembered from the last post. However,...; 辛昕 Programming Basics

Raw os's first anniversary: [align=left][font=宋体][size=12.0pt]On January 15, 2012, I finally mustered up the courage to write a real-time operating system. I had an impulse to do so when I first came into contact with RTOS 10 ye...; jorya_txj Embedded System

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components