Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
HV-HT Series, High Voltage, High Temperature 200°C, C0G Dielectric, 500 – 2,000 VDC (Industrial Grade)
Packaging C-Spec Ordering Options Table
Termination Finish Options
Packaging Type/Options
Standard Packaging – Unmarked
3
Bulk Bag
Waffle Tray
2
7" Tape & Reel
C = 100% Matte Sn
L = SnPb (5% Pb min.)
F = Gold (Au) 30 – 50 µin
G = Gold (Au) 100 µin minimum
13" Reel
7” Tape & Reel/2 mm pitch
4
7" Tape & Reel – 50 pcs
7" Tape & Reel – 100 pcs
7" Tape & Reel – 250 pcs
7" Tape & Reel – 500 pcs
7" Tape & Reel – 1,000 pcs
Blank
1
7292
TU
7411 (EIA 0603 and smaller case sizes)
7210 (EIA 0805 and larger case sizes)
7081
T050
T100
T250
T500
T1K0
7282
7130
Packaging
Ordering Code (C-Spec)
Moisture Sensitive Packaging
5
– Unmarked
3
Waffle Tray
2
7" Tape & Reel
7" Tape & Reel – 50 pcs
7" Tape & Reel – 100 pcs
7" Tape & Reel – 250 pcs
7" Tape & Reel – 500 pcs
7" Tape & Reel – 1,000 pcs
E = Gold (Au) 1.97 – 11.8 µin
F = Gold (Au) 30 – 50 µin
G = Gold (Au) 100 µin minimum
Contact KEMET
6
Default packaging is “Bulk Bag”. An ordering code C-Spec is not required for “Bulk Bag” packaging.
“Bulk Bag” packaging option is not available for Gold (Au) termination finish options and case sizes larger than 2225 (5664 Metric).
2
“Waffle Tray” packaging option is not available for case sizes larger than 2225 (5664 Metric).
3
The terms “Marked” and “Unmarked” pertain to laser marking option of components. All packaging options labeled as “Unmarked” will contain
capacitors that have not been laser marked. The option to laser mark is not available on these devices.
3
Reeling quantities are dependent upon chip size and thickness dimension. When ordering using the “T1K0” packaging option, 1812 through 2225 case
size devices with chip thickness of ≥ 1.9mm (nominal) may be shipped on multiple 7” reels or a single 13” reel. Additional reeling or packaging options
may be available. Contact KEMET for details.
4
The 2 mm pitch option allows for double the packaging quantity of capacitors on a given reel size. This option is limited to EIA 0603 (1608 metric) case
size devices. For more information regarding 2 mm pitch option see “Tape & Reel Packaging Information”.
5
Moisture sensitive packaging is required for Gold (Au) termination option “E” (1.97 µin min / 11.8 µin max.). Not available for case sizes larger than
2225 (5664 Metric).
6
Additional reeling or packaging options may be available. Contact KEMET for details.
[i=s] This post was last edited by paulhyde on 2014-9-15 03:05 [/i] Does anyone have the driver for LDC1000F149? It's urgent. I have the F5526, but it's not realistic to modify it....
When using RAM IP core simulation, how should the input address be controlled? ? The result of Modelsim simulation is incorrect when using counter control. Please teach me how to control the address g...
In the default setting, there is no external crystal oscillator, MCLK=SMCLK=DCO=~800K. When a 32768 crystal oscillator is connected between XIN and XOUT, MCLK=SMCLK=DCO=32*32867=1Mis it like this?Than...
I had dinner with Mr. Shen from East China Normal University, and he talked about people's mentality. Many people are tired because they set too high a goal at the beginning. They always stare at the ...
I saw in the manual that the PWM signal has to pass through the control module before it is finally output from the pin. The control module is introduced as follows:PWM output enable;output polarity c...
I would like to ask how can I find information about all products on a company's website. For example, how can I find the HMC043 sensor on Honeywell's official website?...
Traditional broadcasting systems generally need to be operated manually at a fixed time, and can only realize one-way broadcasting with few functions. Traditional bell ringing equipment has a singl...[Details]
1. Circuit composition
The whole circuit consists of two parts:
1. Power saving control circuit
As shown in the figure below. Including delay circuit and drive circuit.
(1) Delay ci...[Details]
Microcontrollers (MCUs), which are widely used in automotive electronics, are rapidly facing time and cost pressures. The main advantage of using MCUs has always been to create high-level system in...[Details]
1. Introduction
With the growth of parking demand, the scale of parking lots is becoming larger and larger. A lot of research has been done on intelligent parking lots in China, but most of th...[Details]
Converged processors meet scalability requirements
In current embedded system design, solutions based on MCU, DSP, FPGA and ASIC account for more than 90% of the market share. These solutions ...[Details]
With the continuous improvement of the requirements of intelligent building security systems and the continuous improvement of people's safety awareness, indoor anti-theft has gradually attracted peop...[Details]
According to the Industrial Technology Research Institute of Taiwan, due to factors such as the oil crisis and global warming, the issues of energy conservation and environmental protection have at...[Details]
LED technology has made rapid progress, and improvements in chip design and materials have promoted the development of brighter and more durable light sources, and the scope of light source applica...[Details]
A few days ago, I bought an 8LED flashlight in the market (the flashlight uses No. 5 batteries). Because I had other things to do, I didn't pay attention when purchasing it. When I got home and use...[Details]
UDN2916LB is a two-phase stepper motor bipolar driver integrated circuit launched by SANKEN. It can drive dual-winding bipolar stepper motors and is particularly suitable for controlling dual-step ...[Details]
Button cells (also called button cells) are those batteries with equal or larger diameter and height. The current size range of alkaline button cells is specified as follows: diameter 4.8mm-11.4mm,...[Details]
At present, products in the field of monitoring generally focus on the field level, that is, the client/server (C/S) model is adopted, the purpose of which is to ensure the stability and reliability o...[Details]
3. Driving circuit design
The power driver uses a field effect tube, which is a field-controlled device with a capacitance effect between the gate and source, so it has high requirements for t...[Details]
O Introduction
Virtual instrument is a new type of instrument developed with
the development of
computer
technology, electronic measurement technology and communication technology. ...[Details]
1. Explanation of some common English abbreviations in ARM
MSB: most significant bit;
LSB: least significant bit;
AHB: Advanced High-Performance Bus;
VPB: VLSI peripheral bus th...[Details]
Electronics Design Contest
京公网安备 11010802033920号
EEWORLD
