EEWORLDEEWORLDEEWORLD

Part Number

Search

HC-1/S92

Description
general purpose relays relay, vacuum, spdt
CategoryTopical application    Mechanical and electrical/engineering/automation   
File Size488KB,2 Pages
ManufacturerAll Sensors
Download Datasheet Parametric Compare View All

HC-1/S92 Overview

general purpose relays relay, vacuum, spdt

HC-1/S92 Parametric

Parameter NameAttribute value
ManufactureTE Connectivity
Product CategoryGeneral Purpose Relays
Factory Pack Quantity5
KILOVAC High Voltage Relays
HC Series — 3.5 kV Relays
HC-1
No Load Switching
HC-3
Make & Break Load
Switching
Product Facts for HC-1
n
n
n
n
n
n
Widely used for RF
applications
Vacuum dielectric for low
leakage current applications
Copper contacts for high
current capability
Not designed for power
switching
Meets requirements of
MIL-R-83725
QPL version available,
M83725/5-001
Product Facts for HC-3
n
Tungsten contacts for
long life when power
switching
n
For factory-direct application assistance,
dial 800-253-4560, ext. 2055, or
805-220-2055.
Vacuum dielectric for power
switching low current loads
HC-5
Make Only Load Switching
Product Facts for HC-5
n
n
Gas-filled for “make only”
power switching
SF-6 gas-filled for
capacitive discharge
applications
n
Tungsten contacts for
long life when power
switching
Open Contacts to Ground —
HC-1 —2.5 pF
Contact Resistance, Max.
HC-1 — 0.01 ohm
HC-3 — 0.02 ohm
HC-5 — 0.50 ohm*
Operate Time, Max.
— 6 ms
Release Time, Max.
— 6 ms
Shock, 11ms, 1/2 Sine (Peak)
50 g
Vibration
Peak — 10 g (55 to 2000 Hz)
Operating Ambient Temperature
Range
— -55°C to +125°C
Mechanical Life
HC-1, HC-3 — 2 million cycles
HC-5 — 1 million cycles
Weight, Nominal
28.35 g (1.0 oz.)
Note:
*Contact resistance for gas-filled
relays is measured at 28 Vdc, 1
Amp
Product Specifications for
HC-1, HC-3 and HC-5
Contact Arrangement
— SPDT
Contact Form
— C
Test Voltage, DC or 60 Hz (Peak)
5 kV
Rated Operating Voltage (Peak)
DC or 60 Hz — 3.5 kV
2.5 MHz — 2.5 kV
16 MHz — 2 kV
32 MHz — 1.5 kV
Continuous Carry Current, Max.
DC or 60 Hz — HC-1 — 25 A
HC-3 — 18 A
HC-5 — 8 A
2.5 MHz — HC-1 — 14 A
16 MHz — HC-1 — 9 A
32 MHz — HC-1 — 7 A
Coil Hi-Pot (Vrms, 60 Hz) — 500 A
Contact Capacitance
Between Open Contacts —
HC-1 —2 pF
Coil Data
Nominal Volts DC
Pickup, Max.
Dropout
Coil Resistance (±10%)
12 Vdc
8 Vdc
.5-5 Vdc
80
26.5 Vdc
16 Vdc
1-10 Vdc
335
115 Vdc
80 Vdc
5-50 Vdc
6000
Ratings listed are for 25°C, sea level conditions
Ordering Information
Sample Part Number
HC- 1 /12Vdc
Series:
Model:
1
3
5
Coil Voltage:
Blank = 26.5 Vdc
/12Vdc = 12 Vdc
/115Vdc = 115 Vdc
USA: +1 800 522 6752
Asia Pacific: +86 0 400 820 6015
UK: +44 800 267 666
For additional support numbers
please visit www.te.com
7–58
Catalog 5-1773450-5
Revised 3-13
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in millimeters
unless otherwise specified.

HC-1/S92 Related Products

HC-1/S92 HC-1/S48
Description general purpose relays relay, vacuum, spdt general purpose relays relay, vacuum, spdt
Manufacture TE Connectivity TE Connectivity
Product Category General Purpose Relays General Purpose Relays
Factory Pack Quantity 5 40
Power chip static current
How to measure the quiescent current and shutdown current of the power chip?...
kunkunjiang TI Technology Forum
How to make a USB drive into an executable installer
Due to customer requirements, a USB driver needs to be packaged into an installer, as follows: My existing driver contains two files, one is a .ini file and the other is a .sys file. When the USB devi...
hustvic Embedded System
Big Giveaway
Only 1 coin. Cheap processing...
jiangbihao Analog electronics
Thanks to the forum
As soon as the AVR board exchanged for core coins arrived, I couldn't wait to solder it. I would like to thank tiankai001 for lending me the core coins and editor. Thank you for helping me solder well...
陈远明 Microchip MCU
IO port falling edge trigger problem
Can someone please give me some advice on how to configure IO to trigger an interrupt on a falling edge?...
拓磊 Microcontroller MCU
How to convert the data received by MMA7455 into angle? ? Urgent
I am measuring the angle using MMA7455. The data obtained from the measurement is between 0 and 66, except for the highest flag bit. However, I don't know how to convert the data into an angle. Can so...
hopoo Sensor

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1521  506  1649  38  2422  31  11  34  1  49 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号