Resistor values are typically 120 to 240 ohms for 3.3V operation and 82 to 120 ohms for 2.5V
operation.
Figure 7 - Pull Up Pull Down Termination
Resistor values are typically for 3.3V operation
For 2.5V operation, the resistor to ground is 62 ohms and the resistor to supply is 240 ohms
There are numerous application notes on terminating and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 6,
and a pull-up/pull-down scheme as shown in Figure 7. An AC coupling capacitor is optional, depending on the application and the input logic requirements of
the next stage.
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-
terminated, and if one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
LVDS Application Diagrams
+3.3V
OE or NC
10nF
1nF
1
6
Receiver
100
3
4
+3.3V
OE or NC
10nF
1nF
1
6
10nF
100
3
4
Receiver
OE or NC
2
5
OE or NC
2
5
10nF
Figure 8 - LVDS to LVDS, internal 100Ω
Some LVDS structures have an internal 100 ohm resistor on the
input and do not need additional components.
Figure 9 - LVDS to LVDS, External 100Ω and AC block ing caps
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-
terminated, and if one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
Hello everyone, I recently worked on a USB host project of LPC2378+ISP1161, and encountered a few problems to ask everyone: 1. When transferring data in batches, the following situation often occurs (...
[p=20, null, left][color=rgb(73, 73, 73)][font=Verdana, sans-serif][size=3][backcolor=white][b]Introduction[/b] In theory, the power supply rejection ratio (PSRR) measurement is relatively simple. A v...
This is the first time I write an interface that communicates with a PC through RAPI. I encountered the following problem. Could you please give me some advice? The lower computer continuously writes ...
A single-chip microcomputer is also called a single-chip microcontroller. It is not a chip that completes a certain logical function, but a computer system integrated into one chip. In general, a c...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guang...[Details]
Microcontrollers (MCUs), which are widely used in automotive electronics, are rapidly facing time and cost pressures. The main advantage of using MCUs has always been to create high-level system in...[Details]
With the continuous improvement of the requirements of intelligent building security systems and the continuous improvement of people's safety awareness, indoor anti-theft has gradually attracted peop...[Details]
1. Background:
The instrument system parameter detection and control of the chemical production workshop of Tangshan Coal Gas Coking Plant are all analog instruments, some of which are eve...[Details]
Motors are important products that convert electrical energy into mechanical energy to achieve automation, and they are widely used in industrial control, medical electronics, white a...[Details]
LED technology has made rapid progress, and improvements in chip design and materials have promoted the development of brighter and more durable light sources, and the scope of light source applica...[Details]
The emergence and development of street lamps are inseparable from the prosperity and progress of cities, which makes street lamps useful. Conversely, street lamps also make the night of the city n...[Details]
Dual Tone MultiFrequency (DTMF) signaling is gradually being used in push-button telephones around the world. It quickly replaced the dial pulse signaling used in traditional rotary phones because ...[Details]
introduction
Belt drive is a common transmission device used in industrial production. Its commonly used speed detection device is a photoelectric encoder installed at the rotating end of th...[Details]
0 Introduction
In the design and construction of communication systems,
communication power supply
is called the heart of the communication system. The power supply system will dire...[Details]
The biggest advantage of Profibus is that it is guaranteed by the stable international standard EN50170 and has been proven to be universal in practical applications. It has been widely used in man...[Details]
In the TV monitoring system, in order to complete the collection of information from various information points (video, audio, alarm signal) and the control of various front-end devices (PTZ, lens,...[Details]
The programmable controller directly controls the stepper motor, which can significantly reduce the cost of the control system of the modular machine tool automatic production line. The article int...[Details]
Voltage hysteresis is a characteristic of lithium-ion battery and the basis of its existence. The principle is as follows: the thionyl chloride electrolyte of the battery is a strong oxidizing chem...[Details]
Microchip MCU
京公网安备 11010802033920号
EEWORLD
