Resistor values are typically 120 to 240 ohms for 3.3V opera on and 82 to 120 ohms for 2.5V
opera on.
Figure 7 - Pull Up Pull Down Termina on
Resistor values are typically for 3.3V opera on
For 2.5V opera on, the resistor to ground is 62 ohms and the resistor to supply is 240 ohms
There are numerous applica on notes on termina ng and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 6,
and a pull-up/pull-down scheme as shown in Figure 7. An AC coupling capacitor is op onal, depending on the applica on and the input logic requirements of
the next stage.
One of the most important considera ons is termina ng the Output and Complementary Outputs equally. An unused output should not be le un-
terminated, and if one of the two outputs is le open it will result in excessive ji er on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to ji er related problems.
LVDS Applica on Diagrams
+3.3V
OE or NC
10nF
1nF
1
6
+3.3V
OE or NC
10nF
1nF
1
6
10nF
OE or NC
2
5
100
3
4
10nF
OE or NC
2
5
Receiver
100
Receiver
3
4
Figure 8 - LVDS to LVDS, internal 100Ω
Some LVDS structures have an internal 100 ohm resistor on the
input and do not need addi onal components.
Figure 9 - LVDS to LVDS, External 100Ω and AC block ing caps
One of the most important considera ons is termina ng the Output and Complementary Outputs equally. An unused output should not be le un-
terminated, and if one of the two outputs is le open it will result in excessive ji er on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to ji er related problems.
[size=4]I recently bought a GPS module online. I was just learning about MSP430 microcontrollers, so I decided to combine the GPS module with MSP430 and post the code. I found that many online materia...
IEEE 802.11af is a wireless networking standard designed for low-power, long-range wireless local area network (WLAN) operation for smart home and IoT devices. It operates in the TV White Space (TVWS)...
[i=s]This post was last edited by hmf1235789 on 2018-2-2 17:53[/i] [size=4]I would like to ask you a question, how to achieve PWM interlocking of the upper and lower tubes of the IGBT to prevent the u...
Problem: 1. Some DS18B20s are difficult to initialize, and the reading is always 85 degrees. 2. The temperature reading is not smooth, for example, the value of 2: 15 degrees 25 reading changes, while...
error: identifier "XXXX" is undefined
When we find such an error, we should first check whether you really have not defined it in the entire project; secondly, check whether your header files are plac...
Assume that data is read from 8-bit AD (if it is a higher-bit AD, the data type can be defined as int), the subroutine is get_ad();
1. Limited secondary filtering
/* A value can be adjust...[Details]
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
Remote keyless entry (RKE) systems have become popular with users, with more than 80% of new cars in North America and more than 70% in Europe equipped with RKE systems. In addition to the obvious ...[Details]
Floating-point digital signal processing has become a constant requirement for precision technology, often in applications requiring high accuracy in areas such as aviation, industrial machinery, a...[Details]
introduction
In the discharge process of tokamak plasma physics, the study of rupture and sawtooth is of great significance. Rupture and sawtooth exist in most tokamaks. Rupture is a notew...[Details]
No matter which processor you are learning, the first thing you need to understand is the registers and working mode of the processor.
ARM has 37 registers, including 31 general registers and ...[Details]
There are three types of mobile TV: one is based on analog TV broadcasting network, another is based on mobile communication network, and the other is based on digital broadcasting network. The f...[Details]
1 Introduction
Solar street lights are mainly composed of four parts: solar photovoltaic cell components, batteries, charge and discharge controllers, and lighting fixtures. The bo...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
A standard cell
is an electrochemical
cell
used as a voltage reference standard in many electrical standards laboratories
. If properly maintained, standard cells are very stable. The ...[Details]
1. System Structure
This system is a simulation system of indoor air-conditioning temperature/humidity control system. The data acquisition and control center collects temperature/humidity...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
On the afternoon of July 10, Beijing time, Taiwan's largest chip designer MediaTek expects its smartphone chip shipments to grow by double digits in the third quarter of this year, and the company is ...[Details]
Toyohashi University of Technology demonstrated electric field coupled wireless power supply technology using life-size car tires and roads at the wireless technology exhibition "Wireless Technolog...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
