EEWORLDEEWORLDEEWORLD

Part Number

Search

3068-614-2102

Description
Board Connector, 14 Contact(s), 1 Row(s), Male, Straight, 0.156 inch Pitch, Solder Terminal, Natural Insulator, Receptacle
CategoryThe connector    The connector   
File Size153KB,1 Pages
ManufacturerMethode Electronics Inc.
Download Datasheet Parametric View All

3068-614-2102 Overview

Board Connector, 14 Contact(s), 1 Row(s), Male, Straight, 0.156 inch Pitch, Solder Terminal, Natural Insulator, Receptacle

3068-614-2102 Parametric

Parameter NameAttribute value
MakerMethode Electronics Inc.
Reach Compliance Codeunknow
ECCN codeEAR99
Other featuresWITH LOCKING RAMP
subject depth0.45 inch
body length2.178 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact completed and terminatedTIN OVER NICKEL
Contact point genderFEMALE
Contact materialBRASS
contact modeRECTANGULAR
Contact resistance5 mΩ
Contact styleSQ PIN-SKT
DIN complianceNO
Dielectric withstand voltage1500VAC V
Filter functionNO
IEC complianceNO
maximum insertion force8.896 N
Insulation resistance500000000000 Ω
Insulator colorNATURAL
insulator materialNYLON
JESD-609 codee3
MIL complianceNO
Plug contact pitch0.156 inch
Plug informationMULTIPLE MATING PARTS AVAILABLE
Mixed contactsNO
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
OptionsGENERAL PURPOSE
PCB contact patternRECTANGULAR
Plating thickness20u inch
polarization keyPOLARIZED HOUSING
Rated current (signal)7 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.165 inch
Terminal pitch3.96 mm
Termination typeSOLDER
Total number of contacts14
UL Flammability Code94V-0
Evacuation force-minimum value.556 N
Base Number Matches1
.156” (3.96mm)
Through Hole Vertical Mount Connector
3000 SERIES “TERMACON”
PART NUMBER LEGEND
30XX-XXX-XXXX
CONTACT TAIL DIMS (SEE TABLE 2)
CONTACT MATERIAL (SEE NOTE 1)
OPTIONS
2 - HIGH INSERTION FORCE CONTACT
3 - LOW INSERTION FORCE CONTACT
NO. OF POSITONS (SEE TABLE 1)
OPTIONS
0-
1-
3-
6-
7-
8-
WITH LEGS
WITH HOOKS
WITH HOOKS AND LOCKING RAMP
WITH LOCKING RAMP
WITH HOOKS, LOCKING RAMP AND POLARIZING KEY
WITHOUT HOOKS, W/ LOCKING RAMP AND POLARIZING KEY
CONTACT FINISH (SEE NOTE 2)
INSULATOR MATERIAL (SEE NOTE 1)
MATING HEADERS: 3100 SERIES
HOLE
LEG
LOCKING
RAMP
POLARIZING KEY &
LOCKING RAMP
Connector Products
1700 Hicks Road • Rolling Meadows, IL 60008 USA
Telephone: 847.392.3500 • Fax: 847.392.9404
email: mcpsales@methode.com • Web Page: www.methode.com
Featured sharing: Example of single-chip microcomputer controlled stepper motor system (schematic diagram + source program)
The original program was written in C. The schematic diagram was drawn in PROTEL. The circuit schematic diagram of the system is divided into two parts: 1 is the circuit schematic diagram of the micro...
cooljewel Embedded System
S3C2440 unused pin processing problem
S3C2440 has many unused pins, which are GPIO pins by default. There is a register PORT PULL-UP REGISTER (GPBUP-GPJUP). The port pull-up register controls the pull-up resister enable/disable of each po...
xyxzh Embedded System
Enterprises have new ways to deal with RoHS environmental protection directive
At the end of June, the Technical Committee for Environmental Standardization of Electrical and Electronic Products and Systems (TC111) of the International Electrotechnical Union (IEC), the internati...
fighting Analog electronics
Zuo Youding, Jiang Zelin, Lu Jianzhao: Wireless Charging System
[b]Wireless Charging System[/b][b] [/b][b]May 21, 2017[/b][b]Abstract[/b][b]The basic principle of the wireless charging system is to set a coil at both the transmitting end and the receiving end. The...
丁哥 Creative Market
How can I tell if a program is already running or has exited? There is only one exe file for this program.
How can I tell if a program is already running or has exited? There is only one exe file for this program....
panshiowen Embedded System
Add C66x CSL library and header files to the project in CCS
Add C66x CSL library and header files to the project in CCS Download the CSL header files and libraries. After downloading, unzip and install. I installed it in: C:\ti\C6xCSL. After installation, the ...
Aguilera DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2374  59  1883  917  2450  48  2  38  19  50 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号