150W Single Output Switching Power Supply
HLG-150H
series
■
Features :
‧
Universal AC input / Full range (up to 305VAC)
‧
Built-in active PFC function
‧
High efficiency up to 94%
‧
Protections: Short circuit / Over current / Over voltage / Over temperature
‧
Cooling by free air convection
‧
OCP point adjustable through output cable or internal potentiometer
‧
IP67 / IP65 design for indoor or outdoor installations
‧
Type HL LED Driver for use in Class
Ⅰ
, Division 2 hazardous location luminaires
‧
Three in one dimming function (1~10Vdc or PWM signal or resistance)
‧
Suitable for LED lighting and street lighting applications
‧
Compliance to worldwide safety regulations for lighting
‧
Suitable for dry / damp / wet locations
‧
5 years warranty (Note.10)
F
110
M
M
SELV
IP65 IP67
HLG-150H-12 A
Blank : IP67 rated. Cable for I/O connection.
A : IP65 rated. Output voltage and constant current level can be adjusted through internal potentiometer.
B : IP67 rated. Constant current level adjustable through output cable with 1~10Vdc or 10V PWM signal or resistance.
D (option, safety pending) : IP67 rated. Timer dimming function, contact MEAN WELL for details.
SPECIFICATION
MODEL
DC VOLTAGE
CONSTANT CURRENT REGION
Note.4
RATED CURRENT
RATED POWER
RIPPLE & NOISE (max.)
Note.2
VOLTAGE ADJ. RANGE
Note.6
HLG-150H-12
12V
HLG-150H-15
15V
HLG-150H-20
20V
HLG-150H-24
24V
HLG-150H-30
30V
15 ~ 30V
5A
150W
200mVp-p
27 ~ 33V
3 ~ 5A
±1.0%
±0.5%
±0.5%
HLG-150H-36
36V
18 ~ 36V
4.2A
151.2W
200mVp-p
33 ~ 40V
2.5 ~ 4.2A
±1.0%
±0.5%
±0.5%
HLG-150H-42
42V
21 ~ 42V
3.6A
151.2W
200mVp-p
38 ~ 46V
2.16 ~ 3.6A
±1.0%
±0.5%
±0.5%
HLG-150H-48
48V
24 ~ 48V
3.2A
153.6W
200mVp-p
43 ~ 53V
1.92 ~ 3.2A
±1.0%
±0.5%
±0.5%
HLG-150H-54
54V
27 ~ 54V
2.8A
151.2W
200mVp-p
49 ~ 58V
1.68 ~ 2.8A
±1.0%
±0.5%
±0.5%
OUTPUT
6 ~12V
7.5 ~ 15V
10 ~ 20V
12 ~ 24V
12.5A
10A
7.5A
6.3A
150W
150W
150W
151.2W
150mVp-p
150mVp-p
150mVp-p
150mVp-p
10.8 ~ 13.5V 13.5 ~ 17V 17 ~ 22V
22 ~ 27V
Can be adjusted by internal potentiometer A type only
CURRENT ADJ. RANGE
7.5 ~ 12.5A 6 ~ 10A
4.5 ~ 7.5A
3.8 ~ 6.3A
VOLTAGE TOLERANCE
Note.3
±2.5%
±2.0%
±1.0%
±1.0%
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
HOLD UP TIME (Typ.)
±0.5%
±2.0%
±0.5%
±1.5%
±0.5%
±1.0%
±0.5%
±0.5%
Note.8
1000ms,50ms/115VAC
16ms at full load
500ms,50ms/230VAC at full load ; B type 1000ms,200ms/115VAC
230VAC / 115VAC
500ms,200ms/230VAC at 95% load
INPUT
Note.5
VOLTAGE RANGE
FREQUENCY RANGE
POWER FACTOR (Typ.)
TOTAL HARMONIC DISTORTION
90 ~ 305VAC
127 ~ 431VDC
47 ~ 63Hz
PF>0.98/115VAC, PF>0.95/230VAC, PF>0.92/277VAC at full load (Please refer to "Power Factor Characteristic" curve)
THD< 20% when output loading
≧
60% at 115VAC/230VAC input and output loading
≧
75% at 277VAC input
91.5%
92%
93%
93.5%
93%
1.7A / 115VAC
0.75A / 230VAC
0.7A / 277VAC
COLD START 65A(t
width
=425 s measured at 50% I
peak
) at 230VAC
μ
<0.75mA / 277VAC
95 ~ 108%
Protection type : Constant current limiting, recovers automatically after fault condition is removed
Constant current limiting, recovers automatically after fault condition is removed
47 ~ 53V
14 ~ 17V
18 ~ 21V
23 ~ 27V
28 ~ 34V
34 ~ 38V
41 ~ 46V
Protection type :
Shut down o/p voltage with auto-recovery or re-power on to recovery
Shut down o/p voltage, recovers automatically after temperature goes down
-40 ~ +70
℃
(Refer to "Derating Curve")
20 ~ 95% RH non-condensing
-40 ~ +80
℃
, 10 ~ 95% RH
±
0.03%/
℃
(0 ~ 50
℃
)
93.5%
94%
94%
94%
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
OVER CURRENT
PROTECTION
SHORT CIRCUIT
OVER VOLTAGE
OVER TEMPERATURE
WORKING TEMP.
54 ~ 63V
59 ~ 65V
WORKING HUMIDITY
ENVIRONMENT STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
UL8750, CSA C22.2 No. 250.0-08, EN61347-1, EN61347-2-13 independent IP65 or IP67, J61347-1, J61347-2-13 approved ;
SAFETY STANDARDS
Note.7
design refer to UL60950-1, TUV EN60950-1
SAFETY & WITHSTAND VOLTAGE
EMC
ISOLATION RESISTANCE
EMC EMISSION
EMC IMMUNITY
MTBF
OTHERS
DIMENSION
PACKING
NOTE
I/P-O/P:3.75KVAC
I/P-FG:2KVAC
O/P-FG:1.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25
℃
/ 70% RH
Compliance to EN55015, EN55022 (CISPR22) Class B, EN61000-3-2 Class C (
≧
60% load) ; EN61000-3-3
Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, EN55024, light industry level (surge 4KV), criteria A
192.2K hrs min. MIL-HDBK-217F (25
℃
)
228*68*38.8mm
1.15Kg; 12pcs/14.8Kg/0.8CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25
℃
of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Please refer to "DRIVING METHODS OF LED MODULE".
5. Derating may be needed under low input voltages. Please check the static characteristics for more details.
6. A type only.
7. Safety and EMC design refer to EN60598-1, subject 8750(UL), CNS15233, GB7000.1, FCC part18.
8. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time.
9. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
10. Refer to warranty statement.
11. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently
connected to the mains.
150W Single Output Switching Power Supply
Power Factor Characteristic
Constant Current Mode
1 .0 0
0 .9 8
0 .9 6
0 .9 4
0 .9 2
0 .9 0
0 .8 8
0 .8 6
0 .8 4
0 .8 2
0 .8 0
0 .7 8
50%
60%
70%
80%
90%
100%
(150W)
HLG-150H
series
2 7 7 V ac
2 3 0 V ac
1 1 5 V ac
LOAD
EFFICIENCY vs LOAD (48V Model)
HLG-150H series possess superior working eff ic iency t hat up to 94% can be reached in f ield applications.
94
90
86
277Vac
82
78
74
70
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
LOAD
230Vac
115Vac
DRIVING METHODS OF LED MODULE
There are two major kinds of LED drive method "direct drive" and "with LED driver".
A typical LED power supply may either work in "const ant voltage mode (CV) or constant current mode (CC )" to drive the LEDs.
Mean Well's LED power supply with CV+ CC characteristic can be operated at both CV mode (with LED driver, at area (A) and CC mode (direct drive, at area (B).
In t he constant current region, the highest voltage at the output of the driver
depends on t he configuration of the end sys tems.
Should there be any compat ibility issues, please contact MEAN WELL.
(A) Constant
Voltage area
(B)
Constant
Current region
100
50
100
Io (%)
Typical LED power supply I-V curve
File Name:HLG-150H-SPEC 2014-05-30
150W Single Output Switching Power Supply
DIMMING OPERATION (for B-type only)
HLG-150H
series
FG ( Green/Yell ow )
AC/L(Brown)
AC/N(Blue)
HLG-150H
DIM+(B lue )
DIM-(W hi te )
-V(B la ck)
+V(Red)
※
Built-in 3 in 1 dimming funct ion, IP67 rated. Out put constant current level can be adjusted t hrough out put cable by connect ing a resistance or
1 ~ 10Vdc or 10V PWM signal bet ween DIM+ and DIM-.
※
Please DO NOT connect "DIM-" t o "-V".
※
Reference resistance value for output current adjustment (Typical)
Single driver
10KΩ 20KΩ 30KΩ 40KΩ 50KΩ 60KΩ 70KΩ 80KΩ 90KΩ 100KΩ
Resistance
Multiple drivers
value
(N =drive r qua ntity for syn ch ronize d
10K
Ω
/N 20K
Ω
/N 30K
Ω
/N 40K
Ω
/N 50K
Ω
/N 60K
Ω
/N 70K
Ω
/N 80K
Ω
/N 90K
Ω
/N 100K
Ω
/N
d im mi n g op e ra ti on )
OPEN
-----
95%~108%
Percentage of rated current
10%
20%
30%
40%
50%
60%
70%
80%
90%
100%
※
1 ~ 10V dimming function for output current adjustment (Typical)
Dimming value
Percentage of rated current
1V
10%
2V
20%
3V
30%
4V
40%
5V
50%
6V
60%
7V
70%
8V
80%
9V
90%
10V
100%
OPEN
95%~108%
※
10V PWM signal for out put current adjustment (Typical): Frequency range : 100Hz ~ 3KHz
Duty value
Percentage of rated current
10%
10%
20%
20%
30%
30%
40%
40%
50%
50%
60%
60%
70%
70%
80%
80%
90%
90%
100%
100%
OPEN
95%~108%
※Using
the built-in dimming function on B-type model can't turn the lighting fixture tot ally dark. Please refer t o the connection met hod below to
achieve 0% brightness of t he lighting fixt ure connecting t o the LED power s upply unit.
※Direct
connect ing t o LEDs is suggested, but is not suitable for using additional drivers.
Dimming connection diagram f or t urning the lighting fixture ON/OFF :
N
FG
L
Relay
Switch
Adjust er
10K~100K Ohms resistance
1~10V DC Voltage
10V PWM Signal
Green/
Yellow
Brown
Blue
AC/L
AC/N
HLG-150H
B Type
DIM+
DIM-
V(-)
V(+)
Blue
Whi te
Blac k
Red
LED Li ghting Fixture
Using a switch and relay can turn ON/OFF t he lighting fixture.
1.Output constant current level can be adjusted through output cable by connecting a
resistance
or 1~10Vdc or 10V PWM signal bet ween DI M+ and DIM-.
2.The LED lighting fixture can be turned ON/OFF by the switch.
File Name:HLG-150H-SPEC 2014-05-30
NXP MCU
京公网安备 11010802033920号
EEWORLD
