EEWORLDEEWORLDEEWORLD

Part Number

Search

XC6113D638

Description
CMOS Voltage Detector
File Size519KB,26 Pages
Manufacturer
Download Datasheet View All

XC6113D638 Overview

CMOS Voltage Detector

Preliminary
◆CMOS
Voltage Detector
◆Manual
Reset Input
◆Watchdog
Functions
◆Built-in
Delay Circuit
◆Detect
Voltage Range: 1.6~5.0V, ± 2%
◆Reset
Function is Selectable
V
DFL
(Low When Detected)
V
DFH
(High When Detected)
■APPLICATIONS
●Microprocessor
reset circuits
●Memory
battery backup circuits
●System
power-on reset circuits
●Power
failure detection
■GENERAL
DESCRIPTION
■FEATURES
Detect Voltage Range
Hysteresis Range
: 1.6V ~ 5.0V, +2%
(100mV increments)
: V
DF
x 5%, TYP.
(XC6101~XC6107)
V
DF
x 0.1%, TYP.
(XC6111~XC6117)
: 1.0V ~ 6.0V
The XC6101~XC6107, XC6111~XC6117 series are
groups of high-precision, low current consumption voltage
detectors with manual reset input function and watchdog
functions incorporating CMOS process technology. The
series consist of a reference voltage source, delay circuit,
comparator, and output driver.
With the built-in delay circuit, the XC6101 ~ XC6107,
XC6111 ~ XC6117 series’ ICs do not require any external
components to output signals with release delay time.
Moreover, with the manual reset function, reset can be
asserted at any time. The ICs produce two types of
output; V
DFL
(low when detected) and V
DFH
(high when
detected).
With the XC6101 ~ XC6105, XC6111 ~ XC6115 series’
ICs, the WD pin can be left open if the watchdog function
is not used.
Whenever the watchdog pin is opened, the internal
counter clears before the watchdog timeout occurs.
Since the manual reset pin is internally pulled up to the V
IN
pin voltage level, the ICs can be used with the manual
reset pin left unconnected if the pin is unused.
The detect voltages are internally fixed 1.6V ~ 5.0V in
increments of 100mV, using laser trimming technology.
Six watchdog timeout period settings are available in a
range from 6.25msec to 1.6sec.
Seven release delay time 1 are available in a range from
3.13msec to 1.6sec.
Operating Voltage Range
Detect Voltage Temperature
Characteristics
: +100ppm/
O
C (TYP.)
Output Configuration
: N-channel open drain,
CMOS
Watchdog Pin
: Watchdog input
If watchdog input maintains
‘H’ or ‘L’ within the watchdog
timeout period, a reset signal
is output to the RESET
output pin
Manual Reset Pin
: When driven ‘H’ to ‘L’ level
signal, the MRB pin voltage
asserts forced reset on the
output pin.
Release Delay Time
: 1.6sec, 400msec, 200msec,
100msec, 50msec, 25msec,
3.13msec (TYP.) can be
selectable.
Watchdog Timeout Period
: 1.6sec, 400msec, 200msec,
100msec, 50msec,
6.25msec (TYP.) can be
selectable.
■TYPICAL
APPLICATION CIRCUIT
■TYPICAL
PERFORMANCE
CHARACTERISTICS
●Supply
Current vs. Input Voltage
XC61X1~XC61X5 (2.7V)
30
Supply Current:
 
ISS (µA)
25
20
15
10
5
0
0
1
2
3
4
5
Input Voltage:
 
VIN (V)
6
Ta=-40
Ta=25
Ta=85
* Not necessary with CMOS output products.
* ‘x’ represents both ‘0’ and ‘1’. (ex. XC61x1⇒XC6101 and XC6111)
XC6101_07_XC6111_17 ETR0207_009
1/26
【KW41z】Access the Thread network terminal from the public network to turn on the lights
[i=s]This post was last edited by ljj3166 on 2017-7-5 11:26[/i] Using the external network to access the Thread network is a very important part of the original poster's idea. The terminals of the Thr...
ljj3166 NXP MCU
74 series IP packaging based on FPGA vivado 2017.2
74 Series IP Packaging Experiment Guide Based on FPGA Vivado 2017.2 1. Experimental Purpose Master two ways to package IP: GUI and Tcl 2. Experimental Content This experimental guide takes 74LS00 IP p...
大辉哥0614 FPGA/CPLD
09 National Competition E Question Advanced Discussion Group 9742194
[i=s] This post was last edited by paulhyde on 2014-9-15 09:04 [/i] 09 National Competition E Question Discussion Group 9742194 Charger [[i] This post was last edited by bailong39 on 2009-9-2 11:53 [/...
bailong39 Electronics Design Contest
How should the separated high-bit ADC acquisition board and sensor front-end board be connected?
As shown in the figure below, the distance between the left PCB and the right PCB is about 10cm. What method should be used to connect them? I thought about using the SMA interface and connecting them...
littleshrimp Analog electronics
Boring post: Can you guys see if it's worth consulting?
Still about the electric meter in the community. Those who have read the previous posts can skip the next paragraph. To put it simply, the reason is that the light switch of the garage I bought (later...
wangfuchong Talking
Let the software start the win ce 6.0 system automatic startup program
How to compile the registry to implement win ce 6.0 After the system starts up, the desktop is displayed. The program I want to run is displayed on the desktop. Now there is a registry under the HKEY_...
zhanggz02111 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2880  1560  2711  1755  1062  58  32  55  36  22 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号