EEWORLDEEWORLDEEWORLD

Part Number

Search

BUS-63136-460L

Description
Line Driver, 2 Driver, Hybrid, MDFP36
CategoryAnalog mixed-signal IC    Drivers and interfaces   
File Size124KB,16 Pages
ManufacturerData Device Corporation
Download Datasheet Parametric View All

BUS-63136-460L Overview

Line Driver, 2 Driver, Hybrid, MDFP36

BUS-63136-460L Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
MakerData Device Corporation
Reach Compliance Codecompli
ECCN codeEAR99
Differential outputYES
Number of drives2
Interface integrated circuit typeLINE DRIVER
JESD-30 codeR-MDFP-F36
JESD-609 codee0
Number of terminals36
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package body materialMETAL
encapsulated codeDFP
Encapsulate equivalent codeFL36,.8,100
Package shapeRECTANGULAR
Package formFLATPACK
Peak Reflow Temperature (Celsius)NOT SPECIFIED
power supply5,-15 V
Certification statusNot Qualified
Maximum receive delay
Filter level38535Q/M;38534H;883B
surface mountYES
technologyHYBRID
Temperature levelMILITARY
Terminal surfaceTin/Lead (Sn/Pb)
Terminal formFLAT
Terminal pitch2.54 mm
Terminal locationDUAL
Maximum time at peak reflow temperatureNOT SPECIFIED
Base Number Matches1
BUS-63100 SERIES
MIL-STD-1553 DATA BUS
SINGLE AND DUAL TRANSCEIVERS
BUS-63102
BUS-63105
BUS-63125
DESCRIPTION
The BUS-63100 transceivers are
complete transmitter and receiver
pairs conforming fully to MIL-STD-
1553A and 1553B. Features available
with selected models of this high reli-
ability series include: Smiths and
Harris interface type choices,
+12 V/+15 V power supply voltage
range, variable threshold levels, and
single (24-pin DDIP or square) and
completely independent dual redun-
dant (36-pin DDIP) packaging config-
urations. All models are also available
in flat packs.
The receiver section of the BUS-
63100 series accepts phase-modula-
ted bipolar data from a MIL-STD-1553
Data Bus and produces TTL signal
data at its outputs: RX Data Out and
RX Data Out. These outputs repre-
sent positive and negative variations
of the input data signals beyond an
internally fixed or externally set
threshold level. An external STROBE
input enables or disables the receiver
outputs.
The transmitter section accepts bipo-
lar TTL signal data at its TX Data and
TX Data input lines and produces
phase modulated bipolar data at the
TX Data and TX Data outputs. The
transmitters’ output voltage level is
typically 28 Vpp to 30 Vpp. An exter-
nal input, INHIBIT, takes priority over
the transmitter inputs and disables
the transmitter when activated with a
logic “1.”
The small size and different model
capabilities available with the
BUS-63100 series simplify engineer-
ing design, making it an excellent
choice for interfacing with any
MIL-STD-1553 system.
FEATURES
Conforms Fully to MIL-STD-1553A
and 1553B
Some Models Available to Military
(DESC) Drawings
Model Capabilities:
Single or Dual Redundant
Packaging
-12 V/-15 V Power Supply Voltage
Range Available
Harris or Smith’s I/O Compatibility
Small Size:
Single – 24-Pin DDIP or Square
Dual – 36-Pin DDIP Flat Packs
Low Power
High Reliability – LSI
±V
1553
DATA
BUS
+5 V
RECEIVER STROBE
BI PHASE
TTL DATA
PHASE MODULATED
BIPOLAR DATA
RX Data In
SHORT OR
LONG STUB
COUPLING
ISOLATION
TRANSFORMER
RX Data In
RECEIVER SECTION
COMPARATOR
RX Data
LIMITER
FILTER
RX Data
DECODER
COMPARATOR
TRANSMITTER SECTION
DRIVER
TX Data Out
SHAPING
NETWORK
DRIVER
TX Data Out
SHAPING
NETWORK
TX Data In
TX Data In
ENCODER
TX INHIBIT
FIGURE 1. BUS-63100 BLOCK DIAGRAM
M
DDC Custom Monolithics utilized in this product are copyright under the Semiconductor chip Protection Act.
A classic book on switching power supplies
This book explains in detail the design of forward and flyback switching power supplies, including inductance calculation and core selection, and is very suitable for engineers who are just getting st...
zengquan Power technology
I have a question about battery voltage sampling?
I need to design a battery voltage detection circuit. I only need to detect the current voltage and send the sampled voltage directly to the microcontroller through AD conversion. Do I need to add a v...
hunenghl Analog electronics
My understanding of 3G (transferred)
After communicating with all parties, my understanding is as follows: (1) China's principles in choosing 3G technology: practical, inexpensive, and waiting; (2) China is not deliberately waiting for T...
john_wang RF/Wirelessly
52 MCU interrupt priority problem
The microcontroller model is AT89LS52. The serial port interrupt has the highest priority, that is, the serial port position in the IP register is 1, and the other positions are 0. When the interrupt ...
mcd511786450 Embedded System
Introduction to DDR2 and FPGA-based controller design
Introduction to DDR2 and FPGA-based controller design...
iamxiaozhang FPGA/CPLD
Why does the msp430f149 program need to be reset before it can run?
I am a beginner in 149. Today I wrote a small program and burned it into 149 using a hardware emulator. I clicked "Run at full speed" in IAR software, but it didn't work. However, after manually press...
cgj00 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 852  1029  2898  832  399  18  21  59  17  9 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号