Moisture Sensitivity Level (MSL) – This product is Hermetically Sealed
and not Moisture Sensitive - MSL = N/A: Not Applicable
Pb
RoHS/RoHS II
11.5 x 5.0 x 2.5 mm
| | | | | | | | | | | | | | |
FEATURES:
• Reduced height at 2.5mm
• High reliability & Low Cost
• Tight stability & extended temperature
• Proven resistance welded metal package
STANDARD SPECIFICATIONS:
Parameters
Frequency Range
Minimum
3.579545
3.579545
Operation mode
24.01
24.01
Operating Temperature
Storage Temperature
Frequency Tolerance
Frequency Stability over the Operating
Temperature
(
ref. to +25°C)
Equivalent series resistance
(R1)
Shunt capacitance
(C0)
Load capacitance
(CL)
Drive Level
Aging @
25°C per year
Insulation
Resistance
Drive Level Dependency
(DLD,
Minimum
7 points tested:
from
1µW to
500µW)
0
-55
-50
-50
APPLICATIONS:
• Home electronics
• Computers, modems, and communications
• Automotive and industrial
• High-precision TCXO and clock applications
• Microprocessors
Typical
Maximum
70
24.0
70.00
50.00
+70
+125
+50
+50
See table 1 below
7
18
100
500
±10
25% of
Max
ESR
Max
ESR in
Table 1
1000
±5
ºC
ºC
ppm
ppm
Ω
pF
pF
µW
ppm
MΩ
ppm
Ω
Ω
MHz
Fundamental
AT-
cut
(Standard)
3
rd
OT
AT-cut
(Standard)
Fundamental
AT-
cut or
BT-cut (See
options)
See options
See options
See options
Units
Notes
See options
@
100Vdc
±
15V
Δfrequency
(Max –
Min)
ΔESR
(Max – Min)
Max
ESR over DLD
range
Table 1
Frequency (MHz)
3.579 - 4.999 (Fund.)
5.000
-
5.999
(Fund.)
6.000 -
7.999
(Fund.)
8.000
-
8.999
(Fund.)
9.000
-
9.999
(Fund.)
10.000
-
15.999
(Fund.)
16.000
-
50.000
(Fund.)
24.01
-
31.999
(3rd
O/T)
32.000 -
70.00
(3rd
O/T)
ABRACON IS
ISO 9001 / QS 9000
ISO 9001:2008
CERTIFIED
ESR(Ω) max.
180
120
100
80
60
50
40
100
80
Revised: 01.08.13
30332
Esperanza, Rancho Santa
Margarita,
California 92688
tel 949-546-8000
|
fax
949-546-8001
|
www.abracon.com
Visit www.abracon.com for Terms & Conditions of Sale
HC/49US (AT49) MICROPROCESSOR CRYSTAL
ABL2 Series
OPTIONS AND PART IDENTIFICATION:
Pb
RoHS/RoHS II
11.5 x 5.0 x 2.5 mm
| | | | | | | | | | | | | | |
ABL2 -
Frequency in MHz
Please specify the frequency
in xx.xxxxMHz.
e.g. 14.3181MHz
Load Capacitance (pF)
Please specify CL
(Minimum 10pF) in pF or
S for series
Custom ESR if other
than standard
R□
□:
Specify a value in
Ω
(e.g.: R40)
MHz-
-
-
-
-
-
Packaging
Blank: Bulk
T: Tape & Reel
TRAY: Tray
Value Added
I
Insulator Tab
L2
Middle 3rd lead
QXX
Trimmed leads
Q15
for 0.15" length
Oscillation Mode
F: Fund. AT>24MHz
FB: Fund. BT>24MHz
Operating Temp.
A: -10°C ~ +60°C
B: -20°C ~ +70°C
C: -30°C ~ +70°C
N: -30°C ~ +85°C
D: -40°C ~ +85°C
J*: -40°C ~ +105°C
K*: -40°C ~ +125°C
L*: -55°C ~ +125°C
Freq. Tolerance
H5: ± 5 ppm
1: ± 10 ppm
7: ± 15 ppm
2: ± 20 ppm
3: ± 25 ppm
4: ± 30 ppm
Freq. Stability
U**: ± 10 ppm
G: ± 15 ppm
X: ± 20 ppm
W: ± 25 ppm
Y: ± 30 ppm
H: ± 35 ppm
Q: ± 100 ppm
R: ± 150 ppm
NOTE:
* Frequency stability ±50ppm, ±100ppm, ±150ppm only. Contact ABRACON for tighter frequency stability.
** -10 to +60C only.
ABRACON IS
ISO 9001 / QS 9000
ISO 9001:2008
CERTIFIED
Revised: 01.08.13
30332 Esperanza, Rancho Santa Margarita, California 92688
tel 949-546-8000
|
fax 949-546-8001
| www.abracon.com
Visit www.abracon.com for Terms & Conditions of Sale
HC/49US (AT49) MICROPROCESSOR CRYSTAL
ABL2 Series
OUTLINE DIMENSIONS:
Pb
RoHS/RoHS II
11.5 x 5.0 x 2.5 mm
| | | | | | | | | | | | | | |
ABL2 SERIES HC49/US (AT49)
MICROPROCESSOR CRYSTAL
Date of Issue: Jan. 2
nd
, 2013
Page (8) of (10)
8.0
Packaging:
L
5.5mm Min
20.0 ± 0.5mm
Packaging
Bulk
Tape & Reel
11.5 x 5.0 x 2.5 mm
Abracon Drawing # 450715
Revision #: K
T= Tape and reel (1,000pcs/reel)
Dimensions: inch (mm)
TAPE & REEL:
T= Tape and reel (1,000pcs/reel)
Dimensions: mm
ATTENTION:
Abracon Corporation’s products are COTS – Commercial-Off-The-Shelf products; suitable for Commercial, Industrial and, where designated, Automotive Applica-
tions. Abracon’s products are not specifically designed for Military, Aviation, Aerospace, Life-dependant Medical applications or any application requiring high reliability where
component failure could result in loss of life and/or property. For applications requiring high reliability and/or presenting an extreme operating environment, written consent and
authorization from Abracon Corporation is required. Please contact Abracon Corporation for more information.
ABRACON IS
ISO 9001 / QS 9000
ISO 9001:2008
CERTIFIED
Revised: 01.08.13
30332 Esperanza, Rancho Santa Margarita, California 92688
tel 949-546-8000
|
fax 949-546-8001
| www.abracon.com
Visit www.abracon.com for Terms & Conditions of Sale
Center Introduction: Guangdong Embedded Software Public Technology Center (GEC) is the embedded product R&D center of Guangdong Midea Group. It was originally a project that the Guangdong Provincial G...
{:1_112:} How to display an animation on the stc51 MCU tft? Is it to display an image and refresh the screen? Can someone provide a C program and explain it to me? Thank you!!!...
The melting of ice often means the arrival of spring. However, what does the reduction of Beijing Mobile's tariffs, which has been frozen for ten years, mean? " The real purpose of the operator's ta...
Why is it that the BUS in my schematic is connected, and the ERC check is correct, but it is not connected when imported into the PCB? Part of the schematic is as follows. Thanks for your guidance! [[...
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
1. Introduction
Since the 1980s, with the continuous development of automotive electronic technology, there are more and more electronic control units in automobiles, such as electronic fuel i...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
1 Introduction
Building Automation System (BAS) is a distributed monitoring system (DCS) designed according to distributed information and control theory. It is the result of the mutual de...[Details]
1 Introduction
With the development of control, computer, communication, network technology, etc., a new control technology, namely fieldbus, has emerged in the field of industrial control...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
Introduction
In industrial control, speed measurement is often required. Generally, a contact tachometer is used. This tachometer must be placed against the center of the shaft to measure. It...[Details]
1. Proposal of
reconfigurable
measurement and control system
The measurement and control system generally refers to a system based on
computers
to realize data acquisition a...[Details]
Traditional
virtual instruments
consist of a data acquisition
board
based on PCI bus and
corresponding software. However, with
the rapid development of
computer
network techno...[Details]
A stepper motor is an electromagnetic mechanical device that converts an electrical pulse signal into an angular displacement or a linear displacement. The stability and reliability of a stepper mo...[Details]
0 Introduction
There are many types of sensors, and the working principles, measurement targets and measurement environments of different types of sensors vary greatly. The corresponding detection s...[Details]
1 Development of LED Film and Television Lighting
1.1 The significance of developing film and television lighting
Lighting power consumption accounts for a large proportion of the total p...[Details]
The demand for improved healthcare environments is endless, so medical imaging equipment with higher resolution is needed to better observe the human body. High resolution brings problems with sign...[Details]
Battery clamps, commonly known as battery connectors, come in two sizes depending on the thickness of the battery terminals. One is the battery clamp used on thick terminals, with a positive termin...[Details]
Electrostatic coupling and interference occur when a charged object is close to the input of the circuit being measured. At low impedance, the effects of interference are not noticeable because th...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
