FMXMB1318JEF-70.000000M-LF datasheet, PDF

Datasheet> All Categories > Passive components> Crystal/resonator> FMXMB1318JEF-70.000000M-LF

FMXMB1318JEF-70.000000M-LF: DescriptionQuartz Crystal,; CategoryPassive components Crystal/resonator; File Size260KB，1 Pages; ManufacturerFrequency Management International; Environmental Compliance

Download Datasheet Parametric View All

FMXMB1318JEF-70.000000M-LF Overview

Quartz Crystal,

FMXMB1318JEF-70.000000M-LF Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	145048879600
package instruction	HC-49/US, 2 PIN
Reach Compliance Code	compliant
Ageing	5 PPM/YEAR
Crystal/Resonator Type	PARALLEL - 3RD OVERTONE
Drive level	50 µW
frequency stability	0.0015%
frequency tolerance	50 ppm
load capacitance	18 pF
Installation features	THROUGH HOLE MOUNT
Nominal operating frequency	70 MHz
Maximum operating temperature	60 °C
Minimum operating temperature	-30 °C
physical size	L11.5XB4.65XH4.1 (mm)/L0.453XB0.183XH0.161 (inch)
Series resistance	120 Ω
surface mount	NO

Preview

Download Datasheet

View All

FMXMB

SERIES

Thru-hole Crystals

Low Profile

Thru-Hole Package

Multiple Package Heights

Low Cost

HC-49/US

SPECIFICATIONS

Issue 6 - 10182012

Parameter

Frequency Range

Operation Mode

Load Capacitance (CL)

Frequency Tolerance

Temperature Tolerance

Operating Temperature

Storage Temperature

Equivalent Series Resistance (ESR)

Shunt Capacitance (C0)

Drive Level

Aging @ 25°C

All specifications subject to change without notice.

Specification

3.2 - 90 MHz

See Operation Mode and ESR Table

18 pF Std., 8 - 60 pF and Series available

±30 ppm @ 25°C Std. (See Cal. Tol. for Options)

±50 ppm Std. (See Temp. Tol. for Options)

0 to +70°C Std. (See Temp. Range for Options)

-55 to +125°C

See Operation Mode and ESR Table

7 pF max.

50 uW typical, 1 mW max.

±5 ppm per year max.

HC-49/US

OPERATION MODE AND ESR TABLE

Frequency (MHz)

3.200 - 5.999

6.000 - 7.999

8.000 - 9.999

10.00 - 14.99

15.000 - 40.000

27.000 - 70.000

MODE

Fundamental

Overtone

MAX ESR (Ohms)

180

100

120

DIMENSION “H” TABLE

STANDARD MARKING

FMI XX.XXX

XX.XXX FREQUENCY in MHz

Package

Max. Height

0.161” (4.1mm)

0.126” (3.2mm)

0.118” (3.0mm)

NOTE: Standard Specifications for product indicated in

color

Dimensions:

Inches

(mm)

PART DESCRIPTION SYSTEM

MARKING: See Page 52, Format A

FMXM B1 1 18 H J A - XX.XXXXXXM - CM

Product Family

Crystal

Package

B1,

B2 or B3

Mode

1 - Fundamental

3 - 3rd Overtone

Load Cap. (CL)

18 - Standard (pF)

00 - Series

## - Custom (pF)

Cal.

Tol. @ 25°C

±10 ppm

±15 ppm

±20 ppm

±25 ppm

±30 ppm

±40 ppm

±50 ppm

Custom

*Temp. Tol.

D ±10 ppm

E ±15 ppm

F ±20 ppm

G ±25 ppm

H ±30 ppm

I ±40 ppm

J ± 50 ppm

X Custom

Frequency (MHz)

Temp. Range

A 0 to 70 °C

B -20 to 70 °C

C -40 to 85 °C

D -10 to 50 °C

E -10 to 60 °C

F -30 to 60 °C

J 0 to 50 °C

X Custom

Options

BI - Base Insulator

LT - Lead Trimming

LF - Lead Forming

PD - Parameter Data

TD - Temp. Data

CM - Custom Mark

BLANK - None Req’d.

**Check with us for availability.

-55°C TO +125°C Available, Limited Stability Options,

please consult the factory.

1-800-800-XTAL

[9825]

www.fmi-inc.com

Recommended Resources

What sensors does the phone have?

Guest arrival signal recognition circuit

AD524 pin and internal circuit function block diagram

Monochrome display CASPER 1489 power supply circuit diagram

Multipurpose power circuit

DC motor speed control board KJZ-1

I'm looking for some advice. I wrote a pulse generator using Verilog and a weird problem occurred. . .: I made a pulse generator with a pulse interval of 45.5ms and a pulse width of 1us. However, when tested with an oscilloscope, it always fluctuates between 45.4 and 45.6ms. But when I changed the inter...; qqichang FPGA/CPLD

《TMS320X281x DSP Principles and C Program Development》: [[i]This post was last edited by dontium on 2011-12-23 11:32[/i]]...; dontium Microcontroller MCU

About Jlink download AXD debugging problem: , I use mini2440, and the following problem occurs when configuring CodeWarrior. I can't solve it. Can an expert take a look: After I successfully connect with JLINK, why does the value of R0 register...; Learner_new ARM Technology

If you want to know whether the signal generated by the signal generator or function generator is ready or whether it is input according to the set value standard...: If I want to know whether the signal generated by a signal generator or function generator is ready or output according to the set value standard, what instrument can be used to verify it? Please help...; QWE4562009 Integrated technical exchanges

Continuous Development: txj, the purpose of open source is to make a better rtos, and the purpose of closed source is to develop continuously. The two are not in conflict. The problem now is cash flow, marketing, or RAWOS-ba...; yexiaoxin1992 Embedded System

I decided to open a thread, report in every morning and sign in every evening, to see how long I can last: Now on November 18, 2014, 17:01...; Sur Talking about work

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components