FMXMB3318EHE-70.000000M datasheet, PDF

Datasheet> All Categories > Passive components> Crystal/resonator> FMXMB3318EHE-70.000000M

FMXMB3318EHE-70.000000M: DescriptionQuartz Crystal,; CategoryPassive components Crystal/resonator; File Size260KB，1 Pages; ManufacturerFrequency Management International; Environmental Compliance

Download Datasheet Parametric View All

FMXMB3318EHE-70.000000M Overview

Quartz Crystal,

FMXMB3318EHE-70.000000M Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	145049088596
package instruction	HC-49/US, 2 PIN
Reach Compliance Code	compliant
Ageing	5 PPM/YEAR
Crystal/Resonator Type	PARALLEL - 3RD OVERTONE
Drive level	50 µW
frequency stability	0.003%
frequency tolerance	15 ppm
load capacitance	18 pF
Installation features	THROUGH HOLE MOUNT
Nominal operating frequency	70 MHz
Maximum operating temperature	60 °C
Minimum operating temperature	-10 °C
physical size	L11.5XB4.65XH3.0 (mm)/L0.453XB0.183XH0.118 (inch)
Series resistance	120 Ω
surface mount	NO

Preview

Download Datasheet

View All

FMXMB

SERIES

Thru-hole Crystals

Low Profile

Thru-Hole Package

Multiple Package Heights

Low Cost

HC-49/US

SPECIFICATIONS

Issue 6 - 10182012

Parameter

Frequency Range

Operation Mode

Load Capacitance (CL)

Frequency Tolerance

Temperature Tolerance

Operating Temperature

Storage Temperature

Equivalent Series Resistance (ESR)

Shunt Capacitance (C0)

Drive Level

Aging @ 25°C

All specifications subject to change without notice.

Specification

3.2 - 90 MHz

See Operation Mode and ESR Table

18 pF Std., 8 - 60 pF and Series available

±30 ppm @ 25°C Std. (See Cal. Tol. for Options)

±50 ppm Std. (See Temp. Tol. for Options)

0 to +70°C Std. (See Temp. Range for Options)

-55 to +125°C

See Operation Mode and ESR Table

7 pF max.

50 uW typical, 1 mW max.

±5 ppm per year max.

HC-49/US

OPERATION MODE AND ESR TABLE

Frequency (MHz)

3.200 - 5.999

6.000 - 7.999

8.000 - 9.999

10.00 - 14.99

15.000 - 40.000

27.000 - 70.000

MODE

Fundamental

Overtone

MAX ESR (Ohms)

180

100

120

DIMENSION “H” TABLE

STANDARD MARKING

FMI XX.XXX

XX.XXX FREQUENCY in MHz

Package

Max. Height

0.161” (4.1mm)

0.126” (3.2mm)

0.118” (3.0mm)

NOTE: Standard Specifications for product indicated in

color

Dimensions:

Inches

(mm)

PART DESCRIPTION SYSTEM

MARKING: See Page 52, Format A

FMXM B1 1 18 H J A - XX.XXXXXXM - CM

Product Family

Crystal

Package

B1,

B2 or B3

Mode

1 - Fundamental

3 - 3rd Overtone

Load Cap. (CL)

18 - Standard (pF)

00 - Series

## - Custom (pF)

Cal.

Tol. @ 25°C

±10 ppm

±15 ppm

±20 ppm

±25 ppm

±30 ppm

±40 ppm

±50 ppm

Custom

*Temp. Tol.

D ±10 ppm

E ±15 ppm

F ±20 ppm

G ±25 ppm

H ±30 ppm

I ±40 ppm

J ± 50 ppm

X Custom

Frequency (MHz)

Temp. Range

A 0 to 70 °C

B -20 to 70 °C

C -40 to 85 °C

D -10 to 50 °C

E -10 to 60 °C

F -30 to 60 °C

J 0 to 50 °C

X Custom

Options

BI - Base Insulator

LT - Lead Trimming

LF - Lead Forming

PD - Parameter Data

TD - Temp. Data

CM - Custom Mark

BLANK - None Req’d.

**Check with us for availability.

-55°C TO +125°C Available, Limited Stability Options,

please consult the factory.

1-800-800-XTAL

[9825]

www.fmi-inc.com

Recommended Resources

CX23040 (TV and VCR) infrared remote control transmitter circuit

Fully automatic AC voltage stabilizer principle circuit diagram

Output voltage fine adjustment DC-DC converter circuit diagram (b)

Xipu soft starter dual use and one backup control circuit

Active high power factor correction pre-regulator circuit diagram using UC3852

Digital isolation circuit

How to modify the default value of protel99sePCB toolbar?: I am a beginner. When I draw a PCB board, the default values of the tools on the toolbar are all large. How can I make them smaller? Please help!...; Hxon PCB Design

Address bus programming problem: I am now going to write a program for the address bus of arm9 (YC2440) to achieve the function of transmitting data to another board. I wonder if anyone has done it before? Or is there any information...; nankeey Embedded System

XMC4800 Relax ECAT Kit Review 3 - Testing the EtherCAT Slave: [i=s]This post was last edited by tdatd on 2019-1-8 08:23[/i] After setting up the environment and lighting up the LED, we will go straight to our goal - ethercat communication. We will start the test...; tdatd Industrial Control Electronics

If I plan to use the STM32 series of microcontrollers, what tools should I prepare?: I'd like to ask the moderator and all the teachers, if I plan to use the STM32 series of microcontrollers, what tools should I prepare? As for software, I see some people use REALVIEW MDK, but I can't...; zxq180 stm32/stm8

How does EVC implement the GetBitmapBits function?: Dear experts, when I was writing EVC recently, I found that there is a function in EVC that does not have GetBitmapBits. Does anyone have any alternative method?...; wwwapple Embedded System

JZ2440 Development Board: Weidongshan JZ2440 development board, fully functional, with CD information, please contact us if you need it!...; 清心如水 Buy&Sell

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components