EEWORLDEEWORLDEEWORLD

Part Number

Search

SM2512K2343CZTR

Description
Fixed Resistor, Metal Glaze/thick Film, 2W, 234000ohm, 350V, 0.25% +/-Tol, -100,100ppm/Cel, 2512,
CategoryPassive components    The resistor   
File Size2MB,2 Pages
ManufacturerOhmcraft
Environmental Compliance
Download Datasheet Parametric View All

SM2512K2343CZTR Overview

Fixed Resistor, Metal Glaze/thick Film, 2W, 234000ohm, 350V, 0.25% +/-Tol, -100,100ppm/Cel, 2512,

SM2512K2343CZTR Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid740892972
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
JESD-609 codee3
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package height0.76 mm
Package length6.35 mm
Package formSMT
Package width3.18 mm
method of packingTR
Rated power dissipation(P)2 W
resistance234000 Ω
Resistor typeFIXED RESISTOR
seriesSM
size code2512
technologyMETAL GLAZE/THICK FILM
Temperature Coefficient100 ppm/°C
Terminal surfaceTin (Sn) - with Nickel (Ni) barrier
Tolerance0.25%
Operating Voltage350 V

Recommended Resources

[GD32L233C] + 1. Unboxing & Development Environment Setup
[i=s]This post was last edited by chrisrh on 2022-1-4 17:59[/i]1. Unboxing I communicated and placed an order on TMALL on the afternoon of December 31, 2021 and applied for the board. It was delivered...
chrisrh GD32 MCU
PB customized wince problem?
When I customize wince5 with PB, do I have to use the eboot generated at the same time? Is it OK to use someone else's eboot? Why does it stop at "Starting eboot ..." after I customize wince and use t...
bookworm Embedded System
Can the STM32 chip external clock use an active crystal oscillator? Thank you
I am currently working on a board that uses the AD652 chip and also requires an external clock input. I am very confused about the clock and hope you can give me some advice. My thoughts are: 1. STM32...
eeleader stm32/stm8
Why can't I use the view in keil Debug?
I am a novice. Now I am outputting hello. The textbook says that the VIEW of Debug Management can view the output results, but why can't I use it?...
anzx23 Embedded System
What is it like to run high-speed lines on the signal layer of ultra-thick copper?
Author: Huang Gang, member of Yibo Technology Expressway MediaAccording to normal thinking logic, the routing layer of high-speed signals is generally 0.5oz or 1oz. If you see a high-speed signal on t...
yvonneGan PCB Design
The Mistake in the Making of the MCU
In the setting parameters of BCSCTL1 on page 26, XT2OFF and XTS are both 0. I haven't read much of the following content. If there are other errors, I hope readers will point them out and communicate ...
shanshi9du Microcontroller MCU

Popular Articles

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1176  1811  1775  2885  1757  24  37  36  59  49 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号