SnPb end metallization option available upon request
(5% Pb minimum)
Applications
Typical applications include military, space quality and high reliability electronics.
Packaging C-Spec Ordering Options Table (100% Matte Sn and SnPb Terminations)
Packaging Type
1
Bulk Bag/Unmarked
7" Reel/Unmarked
13" Reel/Unmarked
7" Reel/Unmarked/2 mm pitch
2
13" Reel/Unmarked/2 mm pitch
2
1
1
Packaging/Grade
Ordering Code (C-Spec)
Not required (Blank)
TU
7411 (EIA 0603 and smaller case sizes)
7210 (EIA 0805 and larger case sizes)
7081
7082
Default packaging is “Bulk Bag”. An ordering code C-Spec is not required for “Bulk Bag” packaging.
The terms “Marked” and “Unmarked” pertain to laser marking option of capacitors. All packaging options labeled as “Unmarked” will contain
capacitors that have not been laser marked. The option to laser mark is not available on these devices. For more information see “Capacitor Marking”.
2
The 2 mm pitch option allows for double the packaging quantity of capacitors on a given reel size. This option is limited to EIA 0603 (1608 metric) case
size devices. For more information regarding 2 mm pitch option see “Tape & Reel Packaging Information”.
Default packaging is “Bulk Bag”. An ordering code C-Spec is not required for “Bulk Bag” packaging.
“Bulk Bag” packaging option is not available for Gold (Au) termination finish options and case sizes larger than 2225 (5664 Metric).
2
“Waffle Tray” packaging option is not available for case sizes larger than 2225 (5664 Metric).
3
The terms “Marked” and “Unmarked” pertain to laser marking option of components. All packaging options labeled as “Unmarked” will contain
capacitors that have not been laser marked. The option to laser mark is not available on these devices.
3
Reeling quantities are dependent upon chip size and thickness dimension. When ordering using the “T1K0” packaging option, 1812 through 2225 case
size devices with chip thickness of ≥ 1.9 mm (nominal) may be shipped on multiple 7” reels or a single 13” reel. Additional reeling or packaging options
may be available. Contact KEMET for details.
4
The 2 mm pitch option allows for double the packaging quantity of capacitors on a given reel size. This option is limited to EIA 0603 (1608 metric) case
size devices. For more information regarding 2 mm pitch option see “Tape & Reel Packaging Information”.
5
Additional reeling or packaging options may be available. Contact KEMET for details.
2015 TI Internet of Things Competition: Ball Explorer : https://training.eeworld.com.cn/course/2283[b][size=4]Work by the North University of China team: The spherical robot has a spherical shell, whi...
, Arial, sans-serif][size=12px][color=#000][url=https://bbs.eeworld.com.cn/thread-372231-1-1.html]EEWorld Group Buying Activity TMP006 Chip Small Test Resources[/url][/color][/size][/font][/color][col...
1 Design principle - meet the maximum impedance mismatch
Insertion loss should be increased as much as possible, that is, signal reflection should be increased as much as possible. Assume that the out...
Requirements: Convert AC power with a frequency of 50Hz and an effective voltage of 220V into a DC power supply with a stable amplitude and an output current of less than 500mA. Dear brothers and sist...
Traditional broadcasting systems generally need to be operated manually at a fixed time, and can only realize one-way broadcasting with few functions. Traditional bell ringing equipment has a singl...[Details]
1. Circuit composition
The whole circuit consists of two parts:
1. Power saving control circuit
As shown in the figure below. Including delay circuit and drive circuit.
(1) Delay ci...[Details]
1. Introduction
With the growth of parking demand, the scale of parking lots is becoming larger and larger. A lot of research has been done on intelligent parking lots in China, but most of th...[Details]
Converged processors meet scalability requirements
In current embedded system design, solutions based on MCU, DSP, FPGA and ASIC account for more than 90% of the market share. These solutions ...[Details]
Battery life is critical for portable applications. For applications such as smoke detectors, security devices, and thermostats, factory-installed batteries need to last for more than 10 years. The...[Details]
Product series: PB-B-RS232/485 interface (hereinafter sometimes referred to as "interface") is a product in the PROFIBUS bus bridge series.
The main purpose of the bridge series ...[Details]
0 Introduction
Ultrasonic waves
are mechanical waves with a frequency of more than 20KHz, and the propagation speed in the air is about 340 m/s (at 20°C). Ultrasonic waves can be gene...[Details]
UDN2916LB is a two-phase stepper motor bipolar driver integrated circuit launched by SANKEN. It can drive dual-winding bipolar stepper motors and is particularly suitable for controlling dual-step ...[Details]
Various electronic and electromagnetic interference inside and outside the car often puts automotive electronic equipment in dangerous working conditions, degrading the performance of electronic eq...[Details]
Button cells (also called button cells) are those batteries with equal or larger diameter and height. The current size range of alkaline button cells is specified as follows: diameter 4.8mm-11.4mm,...[Details]
As the automobile consumer market heats up, the safety performance of automobiles has attracted more attention from consumers. When driving at high speed, tire failure is the most worrying and diff...[Details]
1. Introduction
Industrial fieldbus technology is one of the technologies that has received the most attention in the automation industry in recent years, and it has brought a qualitative leap...[Details]
Typically, buck regulators are designed for continuous mode operation, which simplifies output voltage calculations and system design. However, if the system is non-synchronous and required to oper...[Details]
In recent years, information technology based on microelectronics and computer technology has developed rapidly, and ultrasonic non-destructive testing instruments have also gained unpreceden...[Details]
1. Architecture and operation of electronic toll collection system
The basic principle of the electronic toll collection system is to enable a special device (on-board unit) installed on t...[Details]
Robotics Development
京公网安备 11010802033920号
EEWORLD
