Ratings at 25°C ambient temperature unless otherwise specified.
JEDEC
Type
Number
General
Semiconductor
Part
Number
Stand-Off
Voltage
V
WM
(V)
Minimum
(3)
Breakdown
Voltage
at 1.0mA
V(
BR
)
(V)
Maximum
Reverse
Leakage
at V
WM
I
D
(µA)
Maximum
Clamping
Voltage
at l
PP
= 1.0A
Vc
(V)
Maximum
Clamping
Voltage
at l
PP
= 10A
Vc
(V)
Maximum
Peak
Pulse
Current
I
PP
(A)
1N6382
1N6383
1N6384
1N6385
1N6386
ICTE-8C
ICTE-10C
ICTE-12C
ICTE-15C
ICTE-18C
8.0
10.0
12.0
15.0
18.0
9.4
11.7
14.1
17.6
21.2
50.0
2.0
2.0
2.0
2.0
11.4
14.1
16.7
20.8
24.8
11.6
14.5
17.1
21.4
25.5
100
90
70
60
50
Notes:
(1) “ C “ Suffix indicates bi-directional
(2) ICTE-5 and 1N6373 are not available as bi-directional
(3) The minimum breakdown voltage as shown takes into consideration the ±1 Volt tolerance normally specified for power supply regulation on most integrated
circuit manufacturers data sheets. Please consult factory for devices that require reduced clamping voltages where tighter regulated power supply voltages
are employed.
(4) Clamping Factor: 1.33 at full rated power; 1.20 at 50% rated power; Clamping Factor: the ratio of the actual Vc (Clamping Voltage) to the V
As traditional cars are developing rapidly towards green environmental protection, intelligent driving, and interconnection, a large number of electronic components with various functions are widely u...
I want to access the image data of a camera on my laptop, such as RGB values, to do some research on image processing. But I don't know how to access this data, nor do I know where there is a related ...
Power carrier remote control is particularly suitable for home use because it does not require additional wiring or occupy radio frequencies. Here is a simple and easy-to-make power carrier remote con...
What do I need to know to participate in the competition?What do ABCDE questions mean?In addition to professional technical discussions, for you who are preparing for the competition for the first tim...
The picture shows the circuit and programming pins I used, and the programming information provided by the chip manufacturer is attached. I really checked it many times and don't know where the proble...
Hello everyone, today I used LPCXpresso, I first built a project, then I put some C files and H files in the root directory, I wanted to add them to the project, but there was no such option, I had no...
The rapid development of the Internet has realized high-speed information transmission and resource sharing, greatly facilitating people's lives. Embedded systems are widely used in various electr...[Details]
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
Microchip's PIC18F46J50 is a low-power, high-performance 8-bit USB microcontroller (MCU) using nanoWatt XLP technology. The current in deep sleep mode can be as low as 13nA, the operating voltage i...[Details]
introduction
Solar cells and LED lighting are typical applications of new energy and energy-saving and efficient technologies. Solar LED lighting uses solar cells to convert solar energy...[Details]
This paper designs a dot matrix LED text display screen that is easy to update, expandable, and low-cost. The way to reduce costs is
① Use the Bluetooth data transmission function of mobile ph...[Details]
Two simple circuits are implemented to drive two LEDs from a battery powered microprocessor.
This design is based on a circuit that uses three resistors and a microprocessor I/O pin as an input h...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
introduction
The emergence of high-performance, low-power embedded CPUs and high-reliability network operating systems has made it possible to implement applications with large amounts of comp...[Details]
Microcalorimetry
is used to determine energy relationships. Microcalorimetry techniques are often required when performing calorimetric experiments with small sample sizes or slow heating rat...[Details]
1 Introduction
Water resources are the basic conditions for human survival and the lifeline of economic development. The reality shows that due to the global shortage of water resources and th...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
PV inverter manufacturer SMA has launched its first DC arc fault circuit interrupter (AFCI) PV inverter and has received UL certification.
The new SunnyBoy AFCI inverter models include 3000-US...[Details]
1 Introduction
There have been many studies on the detection and protection of power grid short circuit and line fault. The short circuit, overload and overvoltage protectors on the market have ...[Details]
Among the many members of the single-chip microcomputer family, the MCS-51 series of single-chip microcomputers has occupied the main market of industrial measurement and control and automation eng...[Details]
From the previous section, we have learned that the timer/counter in the microcontroller can have multiple uses, so how can I make them work for the purpose I need? This requires setting the timer/...[Details]
Integrated technical exchanges
京公网安备 11010802033920号
EEWORLD
