The UT28F256 amorphous silicon anti-fuse PROM is a high
performance, asynchronous, radiation-hardened,
32K x 8 programmable memory device. The UT28F256 PROM
features fully asychronous operation requiring no external clocks
or timing strobes. An advanced radiation-hardened twin-well
CMOS process technology is used to implement the UT28F256.
The combination of radiation-hardness, fast access time, and low
power consumption make the UT28F256 ideal for high speed
systems designed for operation in radiation environments.
A(14:0)
DECODER
MEMORY
ARRAY
SENSE AMPLIFIER
CE
PE
OE
PROGRAMMING
CONTROL
LOGIC
DQ(7:0)
Figure 1. PROM Block Diagram
1
DEVICE OPERATION
The UT28F256 has three control inputs: Chip Enable (CE),
Program Enable (PE), and Output Enable (OE); fifteen address
inputs, A(14:0); and eight bidirectional data lines, DQ(7:0). CE
is the device enable input that controls chip selection, active, and
standby modes. AssertingCE causes I
DD
to rise to its active value
and decodes the fifteen address inputs to select one of 32,768
words in the memory. PE controls program and read operations.
During a read cycle, OE must be asserted to enable the outputs.
PIN CONFIGURATION
PIN NAMES
A(14:0)
CE
OE
PE
DQ(7:0)
Address
Chip Enable
Output Enable
Program Enable
Data Input/Data Output
Table 1. Device Operation Truth Table
1
A14
A12
A7
A6
A5
A4
A3
A2
A1
A0
DQ0
DQ1
DQ2
V
SS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
V
DD
PE
A13
A8
A9
A11
OE
A10
CE
DQ7
DQ6
DQ5
DQ4
DQ3
Notes:
1. “X” is defined as a “don’t care” condition.
2. Device active; outputs disabled.
OE
X
0
1
1
PE
1
1
0
1
CE
1
0
0
0
I/O MODE
Three-state
Data Out
Data In
Three-state
MODE
Standby
Read
Program
Read
2
ABSOLUTE MAXIMUM RATINGS
1
(Referenced to V
SS
)
SYMBOL
V
DD
V
I/O
T
STG
P
D
T
J
Θ
JC
I
I
PARAMETER
DC supply voltage
Voltage on any pin
Storage temperature
Maximum power dissipation
Maximum junction temperature
Thermal resistance, junction-to-case
2
DC input current
LIMITS
-0.3 to 7.0
-0.5 to (V
DD
+ 0.5)
-65 to +150
1.5
+175
3.3
UNITS
V
V
°C
W
°C
°C/W
mA
±
10
Notes:
1 . Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the
device at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
2 . Test per MIL-STD-883, Method 1012, infinite heat sink.
2
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
T
C
V
IN
PARAMETER
Positive supply voltage
Case temperature range
DC input voltage
LIMITS
4.5 to 5.5
-55 to +125
0 to V
DD
UNITS
V
°C
V
DC ELECTRICAL CHARACTERISTICS (Pre/Post-Radiation)*
(V
DD
= 5.0V
±
10%; -55°C < T
C
< +125°C)
SYMBOL
V
IH
V
IL
V
OL1
V
OL2
V
OH1
V
OH2
C
IN 1
C
IO 1, 4
I
IN
I
OZ
PARAMETER
High-level input voltage
Low-level input voltage
Low-level output voltage
Low-level output voltage
High-level output voltage
High-level output voltage
Input capacitance
(TTL)
(TTL)
I
OL
= 4.0mA, V
DD
= 4.5V (TTL)
I
OL
= 200µA, V
DD
= 4.5V (CMOS)
I
OH
= -200µA, V
DD
= 4.5V (CMOS)
I
OH
= -2.0mA, V
DD
= 4.5V (TTL)
ƒ
= 1MHz, V
DD
= 5.0V
V
IN
= 0V
ƒ
= 1MHz, V
DD
= 5.0V
V
OUT
= 0V
Input leakage current
Three-state output leakage
current
V
IN
= 0V to V
DD
V
O
= 0V to V
DD
V
DD
= 5.5V
OE = 5.5V
V
DD
= 5.5V, V
O
= V
DD
V
DD
= 5.5V, V
O
= 0V
TTL inputs levels (I
OUT
= 0), V
IL
=
0.2V
V
DD
, PE = 5.5V
CMOS input levels V
IL
= V
SS
+0.25V
CE = V
DD
- 0.25 V
IH
= V
DD
- 0.25V
-5
-10
5
10
µA
µA
V
DD
-0.1
2.4
15
CONDITION
MINIMUM
2.4
0.8
0.4
V
SS
+ 0.10
MAXIMUM
UNIT
V
V
V
V
V
V
pF
Bidirectional I/O capacitance
15
pF
I
OS 2,3
I
DD1
(OP)
5
Short-circuit output current
90
-90
mA
mA
Supply current operating
@25.0MHz (40ns product)
@22.2MHz (45ns product)
Supply current standby
125
117
2
mA
mA
mA
I
DD2
(SB)
post-rad
Notes:
* Post-radiation performance guaranteed at 25°C per MIL-STD-883 Method 1019 at 1E6 rad(Si).
1. Measured only for initial qualification, and after process or design changes that could affect input/output capacitance.
2. Supplied as a design limit but not guaranteed or tested.
3. Not more than one output may be shorted at a time for maximum duration of one second.
4. Functional test.
5. Derates at 3.0mA/MHz.
3
READ CYCLE
A combination of PE greater than V
IH
(min), and CE less than
V
IL
(max) defines a read cycle. Read access time is measured
from the latter of device enable, output enable, or valid address
to valid data output.
An address access read is initiated by a change in address inputs
while the chip is enabled with OE asserted and PE deasserted.
Valid data appears on data output, DQ(7:0), after the specified
t
AVQV
is satisfied. Outputs remain active throughout the entire
cycle. As long as device enable and output enable are active, the
address inputs may change at a rate equal to the minimum read
cycle time.
AC CHARACTERISTICS READ CYCLE (Post-Radiation)*
(V
DD
= 5.0V
±
10%; -55°C < T
C
< +125°C)
SYMBOL
t
AVAV 1
t
AVQV
t
AXQX 2
t
GLQX 2
t
GLQV
t
GHQZ
t
ELQX2
t
ELQV
t
EHQZ
PARAMETER
Read cycle time
Read access time
Output hold time
OE-controlled output enable time
OE-controlled access time
OE-controlled output three-state time
CE-controlled output enable time
CE-controlled access time
CE-controlled output three-state time
The chip enable-controlled access is initiated by CE going active
while OE remains asserted, PE remains deasserted, and the
addresses remain stable for the entire cycle. After the specified
t
ELQV
is satisfied, the eight-bit word addressed by A(14:0)
appears at the data outputs DQ(7:0).
Output enable-controlled access is initiated by OE going active
while CE is asserted, PE is deasserted, and the addresses are
stable. Read access time is t
GLQV
unless t
AVQV
or t
ELQV
have
not been satisfied.
28F256-45
MIN
MAX
45
45
0
0
15
15
0
45
15
28F256-40
MIN
MAX
40
40
0
0
15
15
0
40
15
UNIT
ns
ns
ns
ns
ns
ns
ns
ns
ns
Notes:
* Post-radiation performance guaranteed at 25
°C
per MIL-STD-883 Method 1019 at 1E6 rads(Si).
1. Functional test.
2. Three-state is defined as a 400mV change from steady-state output voltage.
4
t
AVAV
A(14:0)
CE
t
ELQX
t
ELQV
OE
t
GLQV
DQ(7:0)
t
GLQX
t
AVQV
t
AXQX
t
GHQZ
t
AVQV
t
EHQZ
Figure 2. PROM Read Cycle
RADIATION HARDNESS
The UT28F256 PROM incorporates special design and layout
features which allow operation in high-level radiation
environments. UTMC has developed special low-temperature
processing techniques designed to enhance the total-dose
radiation hardness of both the gate oxide and the field oxide while
The Raspberry Pi family was recently expanded with the new Raspberry Pi Zero W1 (February 2017), a wireless personal computer that costs just $10. It’s a real treat for hobbyists, makers, tinkerers an...
I took some time these two days to read the touch screen routines, learned its working principles and driving methods, and would like to share them with you.The touch screen is different from the rela...
[i=s]This post was last edited by Plakatu on 2022-6-22 15:35[/i]"Some people may think that when the frequency is slightly higher than the resonant frequency, the capacitor becomes inductive and no lo...
In wince5, in the stream interface driver, how to determine the parameters of several interface functions? I have read several stream interface driver codes, and the parameters of the interface functi...
From being a global leader to losing the market, Korean battery manufacturers have always wanted to regain the lost market and dignity, but facing Chinese battery manufacturers represented by CAT...[Details]
To enable real-time monitoring of home security and automatically dial a number for voice prompts or send text messages when an alarm occurs, a GPRS-based embedded telephone alarm system was design...[Details]
Some time ago, I attended the 4th Energy Chemistry Forum of the Chinese Chemical Society and learned about high-energy-density and high-safety batteries. I would like to summarize and share this wi...[Details]
On August 25th, TSMC, the world's leading contract chip manufacturer, attracted significant attention for its decision to build a chip manufacturing facility in Arizona. TSMC primarily manufactures...[Details]
Recently, AstroBo Robot, a subsidiary of Chenxing Automation, launched a new mobile collaborative palletizing product. Leveraging an omnidirectional mobile chassis, an intelligent scheduling system...[Details]
On August 18th, Galaxis, a specialist in integrated intelligent intralogistics robotics, officially unveiled its next-generation, ultra-narrow aisle forklift mobile robot, the "VFR Ultra-Narrow Ser...[Details]
When discussing autonomous driving technology, there are often two extremes: on the one hand, there's the vision of "fully autonomous driving," while on the other, there's concern about potential s...[Details]
On August 22, the National Energy Administration released the latest data, showing that by the end of July 2025, China's total number of electric vehicle charging infrastructure will reach 16.696 m...[Details]
introduction
Sonar imaging is of great significance in marine resource development and defense. Its long range, intuitive display of the observed area, and target identification make it widely...[Details]
A half-bridge is an inverter topology for converting DC to AC. A typical half-bridge circuit consists of two controller switches, a three-wire DC power supply, two feedback diodes, and two capacito...[Details]
Teletrac Navman has launched the Multi IQ dashcam, a cloud-based solution designed for large commercial vehicle operators. It connects up to five cameras to cover the vehicle's interior, sides, and...[Details]
Plug-in hybrid vehicles (PHEVs) utilize two powertrains. Their pure electric range is typically inferior to that of pure electric vehicles, often reaching less than half that. Currently, mainstream...[Details]
introduction
Inverter air conditioners are a trend in the current era and have gradually become commonplace in countless households. Beyond their basic cooling and heating functions, air condi...[Details]
The evolution of high-speed networks remains guided by the same core objectives: increasing data rates, reducing latency, improving reliability, lowering power consumption, and maintaining or exten...[Details]
introduction
The widespread use of air conditioner communication circuits began with the rise of household inverter air conditioners. With China's energy conservation and emission reduction in...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
