shrinkHOoP
Cable Clamp Heat Shrink Grommet Sizes 1 and 5
c
b
a
L
Table of Dimensions, inch (mm):
Part
Descriptio
n
URHR-1
URHR-5
Material:
Inside Diameter
Min. Exp. (a)
Max. Rec’d
(b)
1.00 (25)
2.00 (51)
0.08 (2.0)
0.20 (5.1)
Outside
Diameter
Recovered
(c), Ref
0.250 (6.3)
0.812 (20.5)
Overall
Length
Recovered
L, Ref
0.50 (13)
0.75 (19)
heat shrinkable, crosslinked polyolefin, meets MIL-I-81765/1 Type II with
Shore Hardness value 35+/- 5.
Black
Color:
shrinkHOoP
is a Trademark of Tyco Electronics
Tyco Electronics Corporation
300 Constitution Drive
Menlo Park, CA 94025 USA
Tyco Electronics reserves the right to amend this drawing at any time.
Users should evaluate the suitability of the product for their application.
UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES.
METRIC DIMENSIONS ARE SHOWN IN BRACKETS
DRAWN BY:
CAGE CODE:
Org. Date:
File name:
Specification Control Drawing
Title:
shrinkHOoP –Cable
Clamp Heat
Shrink Grommet
Document No.
URHR-1-and-5
Rev.:
Rev. Date:
F
SCALE:
SIZE:
December 9, 2004
SHEET:
U.NGUYEN
06090
10/03/2001
R040892
None
A
1 of 2
©2004
Tyco Electronics Corporation. All rights reserved
If this document is printed it becomes uncontrolled. Check for the latest revision.
Table 2: Properties
Physical
Property
Tensile strength
Ultimate elongation
Specific gravity
Water absorption
Hardness, Shore D
Flammability
Corrosion resistance
Low temperature flex
4 hours at –67 ± 2°F (-55 ±
1°C)
Heat resistance
168 hours at 347 ± 2°F
(175 ± 1°C)
Heat shock
4 hours at 437 ± 5°F (225 ±
2°C)
Elastic Memory
Requirements
1200 psi (8.3 Mpa) minimum
250% minimum
1.4 maximum
0.5% maximum
35 ± 5
Pass
Pass
Pass
Test method
ASTM D-412
ASTM D-412
ASTM D-792
ASTM D-570
ASTM D-2240
ASTM D-635
MIL-I-81765
MIL-I-81765
200% ultimate elongation,
minimum
1000 psi (6.9 Mpa) tensile
strength, minimum
No cracking, dripping or
flowing
MIL-I-81765
MIL-I-81765
Electrica
l
Dielectric strength
Volume resistivity
Chemical
Fluid Resistance
275% minimum expansion to 4 inch (10 cm) of
a fully recovered test specimen, and 93%
recovery of expanded specimen after oven
condition for 1 minute at 302 ± 4°F (150 ± 2° C)
200 v/mil (7880 v/mm)
minimum
ASTM D-149
12
10 ohm-cm minimum
ASTM D-257
MIL-I-81765
200% ultimate elongation,
minimum
750 psi (5.2 Mpa) tensile
strength, minimum
shrinkHOoP
is a Trademark of Tyco Electronics
Rev. Date:
Rev.:
Document No.
Specification Control Drawing
Sheet:
Dec. 9, 2004
F
URHR-1-and-5
2 of 2
If this document is printed it becomes uncontrolled. Check for the latest revision.
京公网安备 11010802033920号
EEWORLD
