Resistor values are typically 120 to 240 ohms for 3.3V opera on and 82 to 120 ohms for 2.5V
opera on.
Figure 7 - Pull Up Pull Down Termina on
Resistor values are typically for 3.3V opera on
For 2.5V opera on, the resistor to ground is 62 ohms and the resistor to supply is 240 ohms
There are numerous applica on notes on termina ng and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 6,
and a pull-up/pull-down scheme as shown in Figure 7. An AC coupling capacitor is op onal, depending on the applica on and the input logic requirements of
the next stage.
One of the most important considera ons is termina ng the Output and Complementary Outputs equally. An unused output should not be le un-
terminated, and if one of the two outputs is le open it will result in excessive ji er on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to ji er related problems.
LVDS Applica on Diagrams
+3.3V
OE or NC
10nF
1nF
1
6
+3.3V
OE or NC
10nF
1nF
1
6
10nF
OE or NC
2
5
100
3
4
10nF
OE or NC
2
5
Receiver
100
Receiver
3
4
Figure 8 - LVDS to LVDS, internal 100Ω
Some LVDS structures have an internal 100 ohm resistor on the
input and do not need addi onal components.
Figure 9 - LVDS to LVDS, External 100Ω and AC block ing caps
One of the most important considera ons is termina ng the Output and Complementary Outputs equally. An unused output should not be le un-
terminated, and if one of the two outputs is le open it will result in excessive ji er on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to ji er related problems.
I have a question about S3C2440 SPI receiving. The program code is as follows. I can capture the correct waveforms of MISO and MOSI through an oscilloscope, indicating that the data transmission and r...
I tried to draw the board myself. The ceramic antenna I used was RFANT3216120A5T, and I drew it according to the data sheet. First, the balun outputted a 50Ω impedance, and then the antenna. But the r...
Hi everyone, I would like to ask you something:I have a Mitsubishi FR E740 inverter, which is used on a conveyor belt. A proximity switch is used to control the start and stop of the motor. The proxim...
EMC testing includes two aspects: testing the electromagnetic disturbance intensity sent to the outside world and testing its sensitivity under the electromagnetic environment conditions with specifie...
[b]Contents: [/b] Part I Analog Electronic Circuits Chapter 1 Semiconductor Components Chapter 2 Amplifier Basics Chapter 3 Feedback in Amplifiers Chapter 4 Frequency Characteristics of Amplifiers Cha...
Assume that data is read from 8-bit AD (if it is a higher-bit AD, the data type can be defined as int), the subroutine is get_ad();
1. Limited secondary filtering
/* A value can be adjust...[Details]
China's new energy vehicles are in a transition period from research and development to real industrial development. In 2012, with the intensive launch of new energy vehicle policy planning, the de...[Details]
Floating-point digital signal processing has become a constant requirement for precision technology, often in applications requiring high accuracy in areas such as aviation, industrial machinery, a...[Details]
Abstract: In order to generate a stable excitation signal, the design of a digital frequency synthesizer is implemented on FPGA using Verilog hardware language. The design includes accumulator, wav...[Details]
1 Introduction
Solar street lights are mainly composed of four parts: solar photovoltaic cell components, batteries, charge and discharge controllers, and lighting fixtures. The bo...[Details]
Editor's note: In order to help technicians or engineers who have knowledge of PIC microcontroller assembly language quickly master the method of using C language to program PIC microcontrollers, t...[Details]
This controller uses PIC16C54 single-chip microcomputer as the controller, and it is very easy to use: just connect a telephone line to the loudspeaker through the controller, and you can rem...[Details]
Overview
In spectral measurement, photomultiplier tubes (PMT) and charge-coupled devices (CCD) are often used as photoelectric converters. PMT is used in slow-changing, high-precision spectral...[Details]
The concept of state machine
State machine is an important concept in software programming. More important than this concept is its flexible application. In a clear and efficient program, ther...[Details]
LED lighting: Basic circuit design can be completed in as little as one day
Semiconductor manufacturers are also getting involved in the LED lighting business. The power circuit of LED req...[Details]
Since AC mains power may experience power outages, voltage sags and surges, continuous undervoltage and overvoltage, and frequency fluctuations during supply, these factors will affect the continuous ...[Details]
introduction
At present, measuring instruments are developing towards networking, and each individual embedded instrument will become a node on the Internet. This system realizes the network...[Details]
The ARINC429 bus is one of the most commonly used communication buses between various subsystems of avionics. As the "skeleton" of modern avionics systems, once the bus system or the attached airbo...[Details]
In recent years, with the increasing maturity of LED technology, LED light sources have been increasingly widely used due to their advantages of using low-voltage power supply, low energy consumpti...[Details]
There are many types and styles of digital voltmeters in design and development. Traditional digital voltmeters have their own characteristics. They are suitable for manual measurement on site. Tra...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
